|
Tender For Provision Of Deficient Married Accommodation At Fazilka Mil Stn (Job No: - Mwp/Swc-02/2024-25); 1 Lump sum price worked out by the tenderer for“BUILDING /STRUCTURE WORKS as listed in Schedule ‘A’ Section - I 2 Sch A Section- II, INTERNAL ELECTRIFICATION WORKS AND FLAME PROOF FITTINGS 3 Material and labour for concealed Point wiring for one light point/fan point controlled by one switch (using red, black and green colour wires as colour coding) complete with 2.5 Sqmm (nominal cross section area)single core FRLSH PVC insulatedunsheathed and multi strand copper conductor cable 1100 volt (ISI marked)drawn through andincludingPVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc., including Pressed steel powder coated sunken terminal box suitable for modular switch socket (Min 50mm deep and 1.6mm thick sheet, suitable size) concealed in wall, including inner and outer plates (cover plate) suitable for fixing the modular switches/ socket / regulator etc, including provn of 2.5 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3)including fixing ofswitch/socket/regulator etc complete all as specified and as directed. (switch, socket, regulator shall be measured and paid separately under appropriate item of BOQ as supply only but cost of labour for fixing the same shall deemed to be included in the unit rate. ). 4 -do- all as per srl No. 3 above but one three pin switch socket outlet 5 Amps on the same borad 5 -do- all as per srl No. 3 above but one call bell controlled by one bell switch 6 -do- all as per srl No. 3 above but wiring with 2.5 sqmm multistranded cable and earth wire with copper conductor of size 2,5 sqmm for 5 Amps point (on independent board) 7 Material and labour for concealed Point wiring for one socket outlet 15/20 Amps point controlled by one switch (on independant board) (using red, black and green colour wires as colour coding) complete with 4 Sqmm (nominal cross section area)single core FRLSH PVC insulatedunsheathed and multi strand copper conductor cable 1100 volt (ISI marked)drawn through andincludingPVC conduit 25mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc., including Pressed steel powder coated sunken terminal box suitable for modular switch socket (Min 50mm deep and 1.6mm thick sheet, suitable size ) concealed in wall, including inner and outer plates (cover plate) suitable for fixing the modular switches / socket, including provn of 4 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM(1:3), including fixing ofswitch, socket complete all as specified and as directed. (switch, socket shall be measured and paid separately under appropriate item of BOQ as supply only but cost of moudlar cover plate with frame and labour for fixing the same shall deemed to be included in the unit rate). 8 Supply only modular switch 6Amps, piano flush type, single pole, one way (1 module) complete all as specified and as directed by Engineer-in-charge (laminated sheet top cover is included in point wiring). 9 Supply only modular switch 16Amps,piano flush type, single pole, one way (1 module) complete all as specified and as directed by Engineer-in-charge (laminated sheet top cover is included in point wiring). 10 Supply only modularsocket outlet 2 in 1, 6Amps,flush type fixed on laminated sheet top cover complete all as specified and as directed by Engineer-in-charge (laminated sheet top cover is included in point wiring). 11 Supply only modularsocket outlet 5 in 1, 16Amps,flush type fixed on laminated sheet top cover complete all as specified and as directed by Engineer-in-charge (laminated sheet top cover is included in point wiring). 12 Supply and fixing Ceiling Rose, polycarbonate, isolated body, surface bakelite 2 to 3 terminal, 240 volts, 5/6 Amp, ISI Marked complete all as specified and as directed by Engineer-in-charge. 13 Supply and fixingelectric calling Bell Ding Dong type, AC 230 Volts single pole including making elctric connection complete all as specified and as directed by Engr-in-charge. 14 Supply only modular Bell Push switch, piano flush type, 6Amps, single pole, one way (1 module) fixed on laminated sheet top cover (laminated sheet top cover is included in point wiring) complete all as specified and as directed by Engineer-in-charge. 15 Supply and hanging /fixing ceiling fan 1200 mm sweep AC Supply (Input Voltage Range ; 120 to280V), BLDC type, 5 star rated, BEE and ISI Marked super enamelled, copper winding of B class insulation, single phase, maximum 30W (± 10%), Temperature rise 40 degree maximum without remote with and including capacitive regulator, 03 No blades, down rod including accessories, white colour, total harmonic less than 10%, 5 speed, hanging in position including making connection with flexible cord three core twisted copper conductor of suitable sizefrom ceiling rose to fan complete all as specified and as directed by Engr-in-charge.Note :- (i) Serial Number as issued by Engr-In-Charge of celing fan and GE Office name shall also be written on fan with red colour permanent marker and fixing of regulator on switch board, cost for the same shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account 16 Supply and fixing exhaust fan (heavy duty) steel body, AC single Phase 230V, 50Hz, 900RPM, size 300mm sweep with blades and frame including new mosquito stainless steel wire mesh of guage 0.36mm with suitable wooden frame protection against birds etc mounted in suitable opening arrangement in wall and electric connection with and including three core PVC Insulated PVC Sheathed copper conductor flexible cable 24/0.2mm drawn in flexible PVC conduit and hanging on wall with 4 Nos steel fastners 12mm dia 200mm long and making good the disturbed surface complete all as specified and as directed by Engineer-in-charge.Note :- (i) Serial Number as issued by Engr-In-Charge of fan and GE Office name shall also be written on fan with red colour permanent marker, cost for the same shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account (ii) Cost for making suitable cutting/opening in wall for fixing of exhaust fan including making good disturbed surface and masonary work shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. 17 Supply and fixed for SPN 8 way, 240 volt distribution board door made out of CRCA mild steel sheet surface with insulated material like polyester or with powder coating surface mounting with Bus bar rating 200 Amps, dust and vermin proof, IP-43 protected, suitable for incorporation of MCBs and isolators etc complete all as specified and as directed by Engineer-in-charge. 18 Supply and fixed for SPN 6 way, 240 volt distribution board door made out of CRCA mild steel sheet surface with insulated material like polyester or with powder coating surface mounting with Bus bar rating 200 Amps, dust and vermin proof, IP-43 protected, suitable for incorporation of MCBs and isolators etc complete all as specified and as directed by Engineer-in-charge. 19 Supply and fixed for SPN 4 way, 240 volt distribution board door made out of CRCA mild steel sheet surface with insulated material like polyester or with powder coating surface mounting with Bus bar rating 200 Amps, dust and vermin proof, IP-43 protected, suitable for incorporation of MCBs and isolators etc complete all as specified and as directed by Engineer-in-charge. 20 Supply and fixed for TPN distribution board 4 way vertical type double door made out of CRCA mild steel sheet surface with insulated material like polyester or with powder coating flush/surface mounting with copper Bus bar suitable rating with neutral bar and earth bar and cable tie for cable management, IP-54 protection and provision and including MCCB 4 pole 160 Amp, 16 KA as incomer and MCBs as outgoing, dust and vermin proof complete all as specified and as directed by Engineer-in-charge. 21 Supply and fixed of MCB suitable for 240 volts AC Supply, SPN with over load and short circuit protection and rupturing capacity not less than 10 KA, C Curve as 6 to 32 Amps complete all as specified and as directed by Engineer-in-charge. 22 Supply and fixed of MCB suitable for 240 volts AC Supply, SPN with over load and short circuit protection and rupturing capacity not less than 10 KA, B Curve as 40 Amps complete all as specified and as directed by Engineer-in-charge. 23 Supply and fixed of MCB suitable for 240 volts AC Supply, SPN with over load and short circuit protection and rupturing capacity not less than 10 KA, B Curve as 6 to 32 Amps complete all as specified and as directed by Engineer-in-charge. 24 Supply and fixing blanking plate of plastic suitable for any type of DB complete all as specified and as directed by Engineer-in-charge. 25 Material and labour for submain wiring comprising single core, 2 Runs of 4.0 sqmm nominal cross sectional area multi stranded FRLS copper conductor cable, PVC insulated unsheathed 1100 volts grade drawing in and including PVC conduit of size min 20mm dia ISI marked and its fittings concealed in floor/roof / wall complete including provision of 01x4.0 sqmm nominal cross sectional area multi stranded FRLS copper conductor cable, PVC insulated unsheathed 1100 volts grade as earth wire and using color code as per IS complete all as specified and as directed by Engineer-in-Charge. Note : Meter of pipe including fitting and 3 runs of single core cable shall be measured as unit Runing meter. Additional wire/cable required for connecting to MCB shall be included in overall cost quoted. 26 Material and labour for submain wiring comprising single core, 2 Runs of 6.0 sqmm nominal cross sectional area multi stranded FRLS copper conductor cable, PVC insulated unsheathed 1100 volts grade drawing in and including PVC conduit of size min 25mm dia ISI marked and its fittings concealed in floor/roof / wall complete including provision of 01x6.0 sqmm nominal cross sectional area multi stranded FRLS copper conductor cable, PVC insulated unsheathed 1100 volts grade as earth wire and using color code as per IS complete all as specified and as directed by Engineer-in-Charge. Note : Meter of pipe including fitting and 3 runs of single core cable shall be measured as unit Runing meter. Additional wire/cable required for connecting to MCB shall be included in overall cost quoted. 27 Material and labour for submain wiring comprising single core, 2 Runs of 10.0 sqmm nominal cross sectional area multi stranded FRLS copper conductor cable, PVC insulated unsheathed 1100 volts grade drawing in and including PVC conduit of size min 25mm dia ISI marked and its fittings concealed in floor/roof / wall complete including provision of 01x6.0 sqmm nominal cross sectional area multi stranded FRLS copper conductor cable, PVC insulated unsheathed 1100 volts grade as earth wire and using color code as per IS complete all as specified and as directed by Engineer-in-Charge. Note : Meter of pipe including fitting and 3 runs of single core cable shall be measured as unit Runing meter. Additional wire/cable required for connecting to MCB shall be included in overall cost quoted. 28 Material and labour for Earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GIearthing wire of size 4 mm dia by means of GI bolts/nuts/washers and protected by 15 mm bore GI light grade pipe upto test point or upto main switch board, HT/LT equipments, fixing with 02 Nos nuts and bolts and protection pipe fixed with and including flat iron clamps, bolts, nuts and washers. Earth plate shall be surrounded by alternate packed layer 15 cm thick of charcoal or coke and common saltall around bottom and top. 20 mmbore GI medium grade pipe for watering and including funnel, wire mesh, PCC chamber pit made with PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) including necessary form work, excavation and earth work in any type ofsoil, returning filling and disposal of surplus soil to a distance not exceeding 50m,Pit cover 40mm thick made with RCC (1:2:4) type B1 (using 20 mm graded stone aggregate) including TMT reinforcement 8mm dia @ 75mm c/c both way, MS handle 12mm dia, cover rest on MS angle iron frame 40x40x6mm embeded in concrete duly painted with two coats of synthetic enamel paint over a coat ofred oxide primer, complete all as specified & shown in electrical plate No. 3 ofSSR 2009 (Part-I) complete all as specified and as directed by Engineer-in-charge.Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) Protection pipe and GI earthing wire upto test point or upto electric equipment from top of earth plate shall be included in the unit rate of this item. (iii) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge. 29 Supply and fixing LED tube light fitting polycarbonate housing 1 x 18/20Watt, appx 4 feet long, with decorative box linear, housing environment friendly, including electric connection with using 2 core flexible copper conductor cable of size 01 sqmm from ceiling rose to tube fitting, complete fitting with all accessories and following specifications, complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt.(b) Input Voltage range : 140 to 270 volts.(c) Temp operating range : Minus 10°C to Plus 45°C(d) Power factor : Minimum 0.95 (e) THD : Current THD Max10% and voltage THD max 5%(f) IP rating : IP-20.(g) Aluminium housing & Integrated Electronic driver(h)LED Driver of the same make as of the luminaire.(j) LED driver should be complete with all protections vizopen/short circuit protection, over voltage protection, all as per standard design of manufacturer.(k) Surge protection minimum 2.5 kV. (l) CCT : Minimum 6500K(m) CRI : more than 80 (n) Rated life time : 50000 burning hrs @L70 (Average 10 to 12 hrs daily) 30 Supply and fixing LED tube light fitting polycarbonate housing 1 x 10Watt, appx 2 feet long, with decorative box linear, housing environment friendly, including electric connection with using 2 core flexible copper conductor cable of size 01 sqmm from ceiling rose to tube fitting, complete fitting with all accessories and following specifications, complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt.(b) Input Voltage range : 140 to 270 volts.(c) Temp operating range : Minus 10°C to Plus 45°C(d) Power factor : Minimum 0.95 (e) THD : Current THD Max10% and voltage THD max 5%(f) IP rating : IP-20.(g)LED Driver of the same make as of the luminaire.(h) LED driver should be complete with all protections vizopen/short circuit protection, over voltage protection, all as per standard design of manufacturer.(j) Surge protection minimum 2.5 kV. (k) CCT : Minimum 6500K(l) CRI : more than 80 (m) Rated life time : 50000 burning hrs @L70 (Average 10 to 12 hrs daily) 31 Supply and fixing LED lamp 1x9 watt including PVC holder with complete suitable for fixation on wall/roof with body robust corrosion resistant, superior flnish and without any cracks of through holes complete all as specified and directed by Engineer-in-Charge 32 Supply and fixing energy efficient LED security light fitting of 35W pressure die cast aluminium housing/body, heat resistant clear toughened glass,better optics for uniform distribution street/roadway luminaire, with driver, including electric connection with using 3 core flexible copper conductor cable 1.5Sqmm from ceiling rose to light fitting, fixing the light fitting with new bracket made out of GI tubing medium grade 32mm dia, 1.2 metre long bent to shape at 32 degree angle at half metre from bottom, including two Nos clamps made out of MS Flat iron size 25x3 mm with suitable nuts and bolts for fixing of bracket including painting to MS clamp and nut bolts with two coats of aluminium paint over a coat of red oxide primer, complete fitting with all accessories and following specifications, complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt.(b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95(e) THD : Max10%.(f) IP rating : IP66. (g) IK rating:Minimum IK07 (h) Built in potted LED Driver of the make as of the luminaire.(j) LED driver should be complete with all protections vizopen/short circuit protection, over voltage protection, all as per standard design of manufacturer.(k) Surge protection 10 kV (inbuilt + extended) (l) CCT : 5700 K. (m) CRI: More than 80 (n) Lens - High Efficiency wide angle lens. (o) BIS Approved fixtures and driver (p) Rated life time : 50000 burning hrs @L70 (Average 10 to 12 hrs daily) 33 Rigid non metallic PVC Conduit 20mm dia (external) for sub main/telephone wiring inclusive of all fittings such as tees, bends, elbow, reducers, junction boxes bell mouth tube ends and all fixing accessories such as couples, bolts, nuts, saddles, pipe hooks etc complete all as specified and as directed by Engineer-in-charge. 34 Material and labour for Mild steel boxflush mounted of size 100mm x100mmx100mm having holes for 20 mm conduit entry including 02 pin TV socket outlet flush type marked with symbol of TV and 03 mm thick plastic laminated sheeet cover and making good disturbed surfaces of walls by using CM (1:3)complete all as specified and as directed by Engineer-in-Charge 35 Supply, installing, commissioning and testing of electric water heater (Geyser) storage type ABS body of capacity 25 litres, BEE approved 5 Star rating, 230 V , single Phase, AC supply, inner tank made out of heavy duty stainless steel sheet (Designed with single weld line, factory tested with hydraulic pressure as per latest IS code) with glass lined coating complete with all accessories such as safety valve, thermostate, NRV, connection piece PVC connection 600mm long heavy duty suitable for Hot and cold water, three core PVC insulated PVC Sheathed copper conductor flexible cable, 04 Nos suitable size mild steel L-Hook fastener with washer for hanging the geyser and making good the disturbed surface complete all as specified and directed by Engr-in-Charge. 36 Supply and fixing for LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. 37 Supply and fixing Earth continuity conductor or main earthing lead 32x6mm galvanised iron strip including nuts bolts and washer fixed to wall with saddles and fixing screws or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required including making good disturbed surface complete all as specified and as directed.Note :- (i) Conduit/pipe as required, same shall be measured & paid separately under respective item of this Sch/BOQ. 38 Subtotal 39 Lump sum price worked out by the tenderer for“INTERNAL WATER SUPPLY WORKS as listed in Schedule ‘A’ Section - III (Part-I) 40 Sch A Sec - III (Part-II), INTERNAL WATER SUPPLY WORKS 41 Supply and fixing two way Bib cock/Angle stop valve with flange, cast copper alloy chromium plated, screwed down high pressure with on/off handle screwed ends suitable for 15 mm bore pipe iron pipe or for brass ferrule/unions and fixed complete all as specified and as directed. 42 Supply and fixing chlorinated polyvinyl chloride (CPVC) pipe heavy duty outer dia 16 mm having thermal stability for hot and cold water supply including all new CPVC fittings plain & brass threaded like elbow, tee, union, socket, reducer etc. including CPVC solvent cement for jointing and fixed complete to walls, ceiling or laid in floor including complete all as specified and as directed by Engineer-in- charge. Note :- Cutting chases if required same shall be measured and paid separately under appropriate item of BOQ. 43 Supply and fixing chlorinated polyvinyl chloride (CPVC) pipe heavy duty outer dia 20 mm having thermal stability for hot and cold water supply including all new CPVC fittings plain & brass threaded like elbow, tee, union, socket, reducer etc. including CPVC solvent cement for jointing and fixed complete to walls, ceiling or laid in floor including complete all as specified and as directed by Engineer-in- charge. Note :- Cutting chases if required same shall be measured and paid separately under appropriate item of BOQ. 44 Supply and fixing chlorinated polyvinyl chloride (CPVC) pipe heavy duty outer dia 25 mm having thermal stability for hot and cold water supply including all new CPVC fittings plain & brass threaded like elbow, tee, union, socket, reducer etc. including CPVC solvent cement for jointing and fixed complete to walls, ceiling or laid in floor including complete all as specified and as directed by Engineer-in- charge. Note :- Cutting chases if required same shall be measured and paid separately under appropriate item of BOQ.Note for CPVC pipes : pipes inside the building shall be fixed concealed and outside the buildings shall be fixed on the surface with wall hooks as directed by Engr-in-charge. 45 Supply and fixing chlorinated polyvinyl chloride (CPVC) pipe heavy duty outer dia 40 mm having thermal stability for hot and cold water supply including all new CPVC fittings plain & brass threaded like elbow, tee, union, socket, reducer etc. including CPVC solvent cement for jointing and fixed complete to walls, ceiling or laid in floor including complete all as specified and as directed by Engineer-in- charge. Note :- Cutting chases if required same shall be measured and paid separately under appropriate item of BOQ.Note for CPVC pipes : pipes inside the building shall be fixed concealed and outside the buildings shall be fixed on the surface with wall hooks as directed by Engr-in-charge. 46 Supply and fixing single lever concealed diverter incl bath spout & Shower complete all as specified and as directed by Engineer-in-charge. 47 Supply and fixing for brass chromium plated Aquaguard/RO inlet valve or diverted valve with nozzle compatible for all type of water purifier fixing to steel pipe of socket of 15mm bore complete all as specified and as directed by Engineer-in-charge. 48 Supply and fixing for 40mm bore CPVC long handle vavle complete all as specified and as directed by Engineer-in-charge. 49 Supply and fixing health faucet fancy type, CP including 1.25 meter long 8mm dia flexible tube and including wall hook and fixing material complete all as specified and as directed by Engineer-in-charge. 50 Subtotal 51 Lump sum price worked out by the tenderer for“ROAD, PCC TILES ANDHUME PIPE CULVERT WORKS) as listed in Schedule ‘A’ Section -IV (Part-I) 52 Sch A Sec - IV (Part-II), ROAD, PCC TILES ANDHUME PIPE CULVERT WORKS 53 Material and labour for premix bituminous concrete 40mm consolidated thicknesswith min 5.4 % binder content (bitumen of grade VG-30)by weight of total mix using sensor paver electronic sensing device for automatic leveling and profile control withi the specified toleranceand internal heating arrangement for the screed all as specified in Table 500-17 of MoRTH specification for road and bridge works 2013, rolled and compacted to required camber and gradient with tandem vibratory roller 8 to 12 tonne power roller to a uniform smooth surface complete all as specified and as directed by Engineer-in-Charge. 54 Material and labour for Thermo plastic paint road marking 2mm thick painting (lines, dashes, arrows, letters etc) with road safety spikeries glass beads @ 8% by weight including preparation of new or previously treated road surfaces and applying paint by using special applicator machine with heating arrangement complete all as specified and as directed by Engineer-in-Charge 55 Supply and laying/fixing 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & lick compacted bed farce dory meinod using fu mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand;complete all as specified and as directed by Engineer-in-ChargeNote:- Tiles shall be approved by GE before incorporation in the work. 56 Material and labour for sand cushioning, with dry and clean tibba sand (for under ground cable) 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cablecomplete all as specified and as directed.Note:- (i) Punned thickness shall be considered for payment purpose (ii) Approved sand free from vegetations, grass and other deleterious substances shall be used. 57 Material and labour for concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed. 58 Subtotal 59 Lump sum price worked out by the tenderer for“(AREA DRAINAGEWORKS) as listed in Schedule ‘A’ Section -V 60 Lump sum price worked out by the tenderer for“SEWAGE DISPOSAL WORKS as listed in Schedule ‘A’ Section - VI (Part-I) 61 Sch A Sec - VI (Part-II), SEWAGE DISPOSAL WORKS 62 Supply and laying DWCPE (SN8) drain pipes 180 (OD)/163(ID) mm dia pipe as per IS-16098 (Part-II), laid in trenches on and including bed 100mm thick beding comprising of well compacted clean poorly graded gravel, gravel/sand mixture with little or no fines to required slope, including all accessories/fittings/jointing ring, jointing and testing complete all as specified and as directed by Engineer-in-Charge.Note : Excavation, earth work and pedestal /anchorage if required shall be measured & paid separately under respective item of Sch 63 Supply and laying DWCPE (SN8) drain pipes 200 (OD)/175(ID) mm dia pipe as per IS-16098 (Part-II), laid in trenches on and including bed 100mm thick beding comprising of well compacted clean poorly graded gravel, gravel/sand mixture with little or no fines to required slope, including all accessories/fittings/jointing ring, jointing and testing complete all as specified and as directed by Engineer-in-Charge.Note : Excavation, earth work and pedestal /anchorage if required shall be measured & paid separately under respective item of Sch. 64 Subtotal 65 Lump sum price worked out by the tenderer for“SECURITY FENCING AND GATE WORKS as listed in Schedule ‘A’ Section - VII 66 Lump sum price worked out by the tenderer for “EXTERNAL WATER SUPPLY WORKS as listed in Schedule ‘A’ Section-VIII (Part-I) 67 Sch A Sec - VIII (Part-II),EXTERNAL WATER SUPPLY WORKS 68 Supplying, laying, jointing and testing Ductileiron pipe (ISI marked) class K-7, bore 150mm, confirming to IS : 8329-2K, spigot & socketed ends centrifugally cast, with cement mortar lining inside and metallic zinc coating with finishing layer of bituminous paint on outside the pipe, suitable for and including rubber tyton joints (Push-on joint) complete all as specified and as directed by Engineer-in-Charge.Note : (i)Earth work, DI specials/ fittings shall be measured and paid separetly however cost of joining is included in overall cost quoted by the contractor. (ii) Test Certificate for pipes from manufacturer shall be produced. No payment shall be entertained without Test Certificate. 69 Supply and fixing cast iron sluice valve 150 mm dia with flanged ends class PN 1.6(heavy duty ISI marked) confirming to IS:14846-2000, drilled type, complete with stainless steel spindle, CI gate with brass ring, iron wheel handle, complete including jointing material such as nuts, bolts, washers and rubber sheet insertion 3.0mm thick at both ends etc complete all as specified and as directed by Engineer-in-Charge. 70 Material and labour for Construction of brick masonary valve pit chamber size 90 X90 X90 cm (internal dimension) using sub class B bricks complete including excavation & earth work, returning fillig and disposal of surplus soil to distance not exceeding 50m and deposited where directed, PCC (1:3:6) type C-2 using 40 mm graded stone aggregate in foundation, coping on top in PCC (1:2:4) type B-1 using 20 mm graded stone aggregate, brick work in cement mortar (1:4), inner plaster 12 mm thick in cm (1:3) finished even and smooth and pionting flush externally as the work proceeds in the same mortar, MS sheet cover 3.15mm thick mounted on angle iron frame of size 40 x 40 x 6mm with handle and locking arrangement duly painted with two coats of synthetic enamel paint over a coat ofred oxide primer and embeded portion of MS work duly applying black bitumenous paint before embeded complete all as specified and as directed by Engineer-in-Charge. 71 Subtotal 72 Lump sum price worked out by the tenderer for“EXTERNAL ELECTRIFICATION AND LIGHTNING PROTECTION WORKS as listed in Schedule ‘A’ Section - IX (Part-I) 73 Sch A Sec - IX (Part-II), EXTERNAL ELECTRIFICATION AND LIGHTNING PROTECTION WORKS 74 Supply and fixing lightning arresters HT 11000 V non linear expulsion type complete with all fittings, transmission class, discharge capacity 65 kilo amp, confirming to IS 3070 (Part-I) 1985 complete all as specified and as directed by Engineer-in-Charge. 75 Supply, installing, commissioning & testing energy efficient transformer suitable for 315 KVA (Level-2) step down floor mounted outdoor type 11/0.433kv, 3 phase, 50 Hz AC, double wound core type copper wound, oil immersed, air naturally cooled with external cooling tubes, transformer delta connection on HV side and star connected on LV side in accordance with vector symbol Dyn-11 (vector group 4) with neutral brought out on LV side with for earthing and having tapping on HV side for constant output so as to alter/vary secondary voltage (Tapping range + 5 %to - 10% in equal step of 2.5 % ) changed by means of manually operated off load taps changing gear. The voltage regulation shall be as per IS including first fill of transformer oil as per IS-335 and including all fittings/accessories. The limit of temperature rise after continuous full load run as specified in IS-1180 (Part-I) 2014 and BEE Certified shall be suitably adjusted to suit the maximum ambient temperature of 55 degree centigrade as prevalent complete all as specified and as directed and shall be comprised with the following fittings and accessories :- 76 (a) Oil conservator tank with fillings holes and cap filter type drain valve and oil level gauge. (b) Silica gel breather with connecting pipe, first fill of dehydrating agent. (c) Explosion relief mounted on tank with double diaphram and equalizer pipe connected to conservator air tank (pressure release valve) (d) Air release valve plug (e) One cable box on LV side (Secondary) consisting of 04 Nos porcelain bushing with nuts, washers & bushing rods with 01 cable gland suitable for reception of taking out suitable size cable, including gland joints complete all as specified (f) Explosive vent (g) 01 No 100 mm dial type thermometer vapor pressure type having range 0-120 degree centigrade with max temp indicator and resetting device incl max reading pointer washer etc. (h) Thermometer pocket on tank cover (j) 04 Nos plain solid CI detachable rollers (k) Two Nos Earthing terminals marking plate. (l) Rating plate and terminal marking plate(m) Extra bushing for neutral outside the cable box brought out on LV side. (n) First filling of oil conforming to IS and tested upto 60 KV dielectric strength (o) Lifting lugs (p) Oil drain valve with plug (q) One cable box on HV side (Primary) consisting of 01 cable gland suitable for reception of taking in HT cable including gland joints complete all as specified (r) Hand hole of sufficient size to assess interior of tank (s) Dehydrating breather with first filling of Dehydrating agent (t) Two earthing terminal on tank body to facilitate fixing of 32x6mm GI strip. (u) Rating plate with terminal marking plate (v) Inspection cover. 77 Supply, installation, commissioning and testing of factory made (CPRI approved) LT panel Board of suitable size, outdoor type (double door both side openable including locking arrangements) 415 Volts, dust proof, vermin proof made out of CRCA sheet 3.15 mm thick powder coated and fully compartmentalized inner panel with 2 mm thick CRCA sheet powder coated, to accommodate the incoming and outgoing each switch gear shall have be independent opening and having provision for front and rear side opening with double door with hinges including provision of rubber beading and brass cable glands for each cable to make it weather and vermin proof, provision of air fins for ventilation, complete with separate bus bar chamber, panel shall be mounted on angle iron frame and 04 Nos legs made from angle of size 50x50x6mm, legs shall be 750 mm long, 300 mm grouted in blocks of PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) with 450 mm ground clearance, frame and legs duly spray painted with seven tank process internally and externally with two coats of synthetic enamel over a coat of red oxide primer, internal wiring of panel board with solid conductor copper cable single core of suitable size, danger notice plate for LT with conventional skull and bones duly rivited/ pasted to the panel board door, complete including all connection incoming/ outgoing all as directed by Engr-in-charge and comprising of following accessories:- 78 (a) Copper bus bar of 800 Amp capacity, 4 strip mounted on porcelain insulators. (b) MCCB 4 pole with thermal magnetic release adjustable type with breaking capacity 36 KA, 500 Amp (Incomming).(c) MCCB 4 pole with thermal magnetic release adjustable type with breaking capacity 25 KA, 125 Amp - 07 (for 07 blocks).(d)MCB TPN 32 Amps -01 Nos (for street lights).(e) Digital Voltmeter 96x96mm flush secure panel mounting type 0-500V with selector switch -01.(f) Digital Amp meter 96x96mm flush secure panel mounting type 0-400Amp with selector switch with CT -01. (g) RYB LED indicating lamp set of three -01. 79 Supply, installation, commissioning and testing of factory made (CPRI approved) LT panel Board of suitable size, outdoor type (double door both side openable including locking arrangements) 415 Volts, dust proof, vermin proof made out of CRCA sheet 3.15 mm thick powder coated and fully compartmentalized inner panel with 2 mm thick CRCA sheet powder coated, to accommodate the incoming and outgoing each switch gear shall have be independent opening and having provision for front and rear side opening with double door with hinges including provision of rubber beading and brass cable glands for each cable to make it weather and vermin proof, provision of air fins for ventilation, complete with separate bus bar chamber, panel shall be mounted on angle iron frame and 04 Nos legs made from angle of size 50x50x6mm, legs shall be 750 mm long, 300 mm grouted in blocks of PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) with 450 mm ground clearance, frame and legs duly spray painted with seven tank process internally and externally with two coats of synthetic enamel over a coat of red oxide primer, internal wiring of panel board with solid conductor copper cable single core of suitable size, danger notice plate for LT with conventional skull and bones duly rivited/ pasted to the panel board door, complete including all connection incoming/ outgoing all as directed by Engr-in-charge and comprising of following accessories:- 80 (a)Aluminium bus bar Cap 150 Amp capacity with heat shrinkable PVC Colour sleeves - 04 Nos.(b) MCCB 4 pole with thermal magnetic release adjustable type with breaking capacity 36 KA, 100 Amp (Incomming).(c) MCB SPN with thermal magnetic release adjustable type with breaking capacity 16 KA, 32 Amp - 16 (outgoing).(d) Digital Voltmeter 96x96mm flush secure panel mounting type 0-500V with selector switch -01.(e) Digital Amp meter 96x96mm flush secure panel mounting type 0-400Amp with selector switch with CT -01. (f) RYB LED indicating lamp set of three -01. 81 Supply, installation, commissioning and testing of factory made (CPRI approved) LT panel Board of suitable size, outdoor type (double door both side openable including locking arrangements) 415 Volts, dust proof, vermin proof made out of CRCA sheet 3.15 mm thick powder coated and fully compartmentalized inner panel with 2 mm thick CRCA sheet powder coated, to accommodate the incoming and outgoing each switch gear shall have be independent opening and having provision for front and rear side opening with double door with hinges including provision of rubber beading and brass cable glands for each cable to make it weather and vermin proof, provision of air fins for ventilation, complete with separate bus bar chamber, panel shall be mounted on angle iron frame and 04 Nos legs made from angle of size 50x50x6mm, legs shall be 750 mm long, 300 mm grouted in blocks of PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) with 450 mm ground clearance, frame and legs duly spray painted with seven tank process internally and externally with two coats of synthetic enamel over a coat of red oxide primer, internal wiring of panel board with solid conductor copper cable single core of suitable size, danger notice plate for LT with conventional skull and bones duly rivited/ pasted to the panel board door, complete including all connection incoming/ outgoing all as directed by Engr-in-charge and comprising of following accessories:- 82 (a)Aluminium bus bar Cap 150 Amp capacity with heat shrinkable PVC Colour sleeves - 04 Nos.(b) MCCB 4 pole with thermal magnetic release adjustable type with breaking capacity 16 KA, 100 Amp (Incomming).(c) MCB SPN with thermal magnetic release adjustable type with breaking capacity 16 KA, 20 Amp - 07 (outgoing).(d) Digital Voltmeter 96x96mm flush secure panel mounting type 0-500V with selector switch -01.(e) Digital Amp meter 96x96mm flush secure panel mounting type 0-100Amp with selector switch with CT -01. (f) RYB LED indicating lamp set of three -01. 83 Supply and fixing cable junction box of Size 280mm x 200mm x100mm or any other higher size (Suitable for Pole mounting) complete with fixing accessories. Junction box should be insulated and made out of polycarbonate with glass fiber re-inforced material. The polycarbonate junction box shall be environment frinedly, recyclable, UV resistant, halogen and silicon free, anti acid and anti corrosive. The junction box knock out on four side wall and following specifications and all as directed by Engr-in-Charge :-(a) The junction box shall be rated for degree ofIP 65 (ingress protection) in accordance with IEC 60529.(b) The gasket material shall be polyurethane or silicon and gasket shall be internally embedded.(c) Junction Box must meet the provision laid down in IEC 60998-1, IEC-60695-22, IEC 60670-2 to 5 and grey color according to RAL-9011/ 7035.(d) The manufacturer of junction box shall submit a copy of IEC certificate and glow wire test for 960 degree.(e)Junction box shall be fire retardant and self extiguishing in accordance with IEC60695-2 to 11, DIN VDE 0304 Part-3, UL94 V-2 flammability standard. (f) The impact strength of polycarbonate enclosures /boards i.e. the degree of protection against mechanical load shall be in accordance with EN 50298-98 for IK08.(g) Junction box shall have 4 pole tinned copper bus bar of size 25mmx3mm complete with one number 20Amp MCB SP 10KA (h) Manufacturer should submit routine test certificate for junction box. (j) Suitable size of mild steel Clamps and screws/nut bolt shall be used for fixing of Junction box.. 84 Material and labour for Earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GIearthing strip 32x6mm by means of GI bolts/nuts/washers and protected by 40 mm bore GI light grade pipe upto 7.5 mtr length, fixing with 02 Nos nuts and bolts and protection pipe fixed with and including flat iron clamps, bolts, nuts and washers. Earth plate shall be surrounded by alternate packed layer 15 cm thick of charcoal or coke and common saltall around bottom and top. 20 mmbore GI medium grade pipe for watering and including funnel, wire mesh, PCC chamber pit made with PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) including necessary form work, excavation and earth work in any type ofsoil, returning filling and disposal of surplus soil to a distance not exceeding 50m,Pit cover 40mm thick made with RCC (1:2:4) type B1 (using 20 mm graded stone aggregate) including TMT reinforcement 8mm dia @ 75mm c/c both way, MS handle 12mm dia, cover rest on MS angle iron frame 40x40x6mm embeded in concrete duly painted with two coats of synthetic enamel paint over a coat ofred oxide primer, complete all as specified & shown in electrical plate No. 3 ofSSR 2009 (Part-I) complete all as specified and as directed by Engineer-in-charge.Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) Protection pipe and GI earthing strip upto 7.5 mtr from top of earth plate shall be included in the unit rate of this item. (iii) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge. 85 Material and labour for sand cushioning, with dry and clean tibba sand (for under ground cable) 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cablecomplete all as specified and as directed.Note:- (i) Punned thickness shall be considered for payment purpose (ii) Approved sand free from vegetations, grass and other deleterious substances shall be used. 86 S&F for GI steel light grade 32 mm dia bent to shape of offset angle upto 45 degree for fixing of security light fitting GI Pipe 1.5 Mtrs including MS Clamp and nut bolts complete all as specified and as directed by Engr-in-Charge. 87 Subtotal 88 Sch A Sec - X, FIRE FIGHTING EQPT WORKS 89 Supply and fixing fire hydrant landing valve type A (double head outlet) gunmetal of 65 mm dia with 63 mm dia female outlet complete and 65 mm inlet with rubber blank cap and chain as per IS 5290-1983, suitable for brigade hose of 63 mm with couplings conforming to IS 903 (for internal hydrant at Ground floor to 3rd floor and roof) complete all as specified and as directed. 90 Supply, installing, commissioning and testing of Fire Hose Cabinet to be mounted externally near the Hydrant Post fabricated from 16 SWG MSSteel of appox size 800 mm x 600 mm x 450 mm with a canopy, door with 4 mm glass encased in heavy grade rubber beading, a key box in built in the box, suitable to accommodate one hydrant valve, one branch nozzle and 30 mtrs hose reel, weather proof, Finished with and including painting of two coats of synthetic enamel paint of post office red colour over a coat of red oxide primer ( Sample to be approved prior to entire supply) complete all as specified and as directed. 91 Supply, installing, commissioning and testingof wall mounting swinging type First aid firehose reel with drum, hanging bracket, 30 mtr long and20mm dia high pressure hose reel as per IS 444 with gunmetal shut off nozzle having 5mm dia orifice. The hose reel shall be conforming to IS 884-1985. Drum shall be fixed on adjoining wall through anchor fasteners/cement concrete book or MS stand as per site requirement complete all as specified and as directed. 92 Supply, installing, commissioning and testing of 63mm dia Gun metal, short type, instantaneous pattern branch pipe to suit fire hose delivery coupling of 63 mm size complete with GM nozzle of 20 mm nominal size conforming to IS 8090 complete all as specified and as directed. 93 Supply, installing, commissioning and testing of gun metal body Butterfly valves of size 63mm dia, IS:210, PN-16, confirming to IS:13095 complete all as specified and as directed. 94 Supply, installing, commissioning and testing of Booster Pump 30 m head, 450LPM discharge, 440 V, 3 Phase, 50Hz confirming to IS- 12469 :1988 With CI Casing bronze impeller and stainless steel shaft mounted on heavy duty bearings complete all as specified and as directed. 95 Supply, installing, commissioning and testing 65mm nominal bore, wall thickness 6mm, MS heavy duty (C Class) flanged pipe, ISI marked (IS : 1239) with all necessary fittings & fabrication like tees, elbows, flanges, reducers, gaskets, nuts and bolts etc welding or screwed joints as required including fixing of pipe with necessary standard clamps structural steel supports (chilly make) as required/directed at site including painting of two coats of synthetic enamel paint of post office red colour over two coats of red oxide primer complete all as specified and as directed. 96 Supply and fixing trolley mounted water stored pressure type fire extinguishers, 9 Ltr capacity conforming to IS:13386 with extinguishing agent :water+AFFF and propelling Nitrogen gas, wall bracket handle fitted with high pressure flexible discharge hose with discharge throw of 2-5 Mtrs.,with ISI certification markcomplete all as specified and as directed. 97 Supply and fixing carbon-di-oxide 3 Kgs capacity fire extinguisher (light weight squeeze grip type) fitted with high pressure wire braided hose and horn shall be flat type and equipped with diffuser inside the horn, and cylinder bearing No., confirming to IS:15683:2006. Fire rating 3A: 89B, ISI certification mark complete all as specified and as directed. 98 Supply and fixing Dry Chemical Powder Fire Extinguisher ( ABC POWDER ) 9 Kgs capacity Stored Pressure type, CE Mark Valve with NRV & Safety Release Provision with EPDM Rubber Hose, The extinguisher is internally coated with Epoxy Polyester and externally coated with Pure Polyester Powder and confirming to IS:15683:2006. Fire rating 3A: 89B, ISI certification mark complete all as specified and as directed. 99 Supply and fixing mechanical foam Extinguisher of 9 Ltr capacity and confirming to IS:15683:2006 complete all as specified and as directed. 100 Supply and fixing fire buckets (dry sand)of 7 Kg capacity including hanging arrangements complete all as specified and as directed. 101 Supply and fixing emergency Exit Sign Board with double side adhesive tape vinyl sticker with forex board (Green and White colour) 30 cm x 10 cm complete all as specified and directed. 102 Subtotal 103 Lump sum price worked out by the tenderer for“LIFT WORKS as listed in Schedule ‘A’ Section - XI (Part-I) 104 Sch A Sec - XI (Part-II), (LIFT WORKS) 105 Supply, installing, commissioning and testing 13 passenger lift, having 1.0 m/s car speed, gearless motor suitable for 3- Ph, 415 V, 50 Hz electric power supply, conforming to IS-14665, suitable to serve G + 3 upper floors with AC variable voltage & variable frequency drive (VVVF drive), complete with all standard accessories, simplex full collective operation, centre opening doors with door drive, sliding stainless steel doors, automatic rescue device (ARD) system, 2D infrared sensor in full height of door & built in press and speak 3 way intercom. Complete all as specified and as directed and shall conform to the following specifications: 106 Type of Lift : Passenger Lift 107 Capacity of Lift : 884 Kg, 13 Person 108 Rise : up to G+3 Bldg 109 Stop and opening - 04 stops with all opening on the same side 110 Controller type : Microprocessor based 111 Drive : AC VVVF drive 112 Power Supply : 400/415 Volts (3 Phase AC) 113 Operation : Full collective operation 114 Car Group : Simplex Type 115 Machine : Gearless motor located above shaft in machine room 116 Traction Media : Steel rope 117 Car Finish : Rear Mid Panel, Rear Corner Panel, Side Mid Panels, Side Corner Panels, Front Panels all are made of Stainless Steel SS304 with honey comb finish 118 False Ceiling Finish : Stainless steel with hairline finish and with provision for LED lights specified here-in-after. 119 Ventilation : PVC heavy duty Cross Flow Fans 120 Hand Rails : Stainless Steel Finish round Handrails on rear car panels 121 Flooring :20mm thick Granite to be provided in the recess car cabin floor and fixing with suitable adhesive over aluminium chequered plate in one piece minimum 3mm thick. 122 Car door and Landing Door finish : Stainless steel SS-304, mirror finish outside 123 Fire rated doors : Fire rating - 60 Minutes 124 PIT DEPTH: 1600 125 OVERHEAD : 4500 126 HOISTWAY DIMENSIONS(W x D – mm) : 2500 mm W x 1900 mm D 127 Car Size (W x D x H - mm) : As per IS-14665 (Part 3 Sec-I) : 2000, height 2200 mm 128 CAR & HOISTWAY DOOR TYPE : Central opening (CO) doors 129 DOOR OPENING (W x H - mm) : 900 mm W x 2000 mm H 130 DOOR OPERATOR : VF 131 COP : COP (car operating panel) and LOP (landing operating panel) in Stainless Steel Hairline finish with display. 132 CAR POSITION INDICATOR : Dot Matrix type 133 HALL FIXTURES : Dot Matrix type 134 HALL FIXTURE FACE PLATE : Stainless steel hairline finish-SS-304 135 HALL BUTTON ARRANGEMENT: Hall and call Buttons with illumination and Braille 136 Car and counter weight guide as per OEM recommendation 137 Terminal buffers metal spring/oil buffer as per OEM recommendation 138 STANDARD FEATURES :Anti-nuisance Car Call Protection, Independent Service, Overload Device, Nudging, Emergency Car Light Unit, Infrared Curtain Door Protection, Door Time Protection, Emergency Alarm Button, Extra Door Time of Lobby & Parking Door Open/Close Button, Manual Rescue Operation, Auto Fan Cut Off, Over Speed Governor for Car 139 ALSO INCLUDED : Emergency Firemen’s Service, Automatic Rescue operation, Intercom. 140 Car Enclosure: Manufactured with stainless steel frame not less than 1.5mm with honey combfinish (SS-304) having stainless steel false ceiling with hairline finish, internal lighting arrangement with LED sleek light fittings (as per manufacturer’s instructions, minimum 04 Nos) operated on commercial supply and one LED light fitting operated on battery with inverter as emergency light, complete internal ventilation system provided with concealed axial / cross flow fan with auto cut-off system and stainless steel grill / wire-mesh for protection 141 Floor announcement system in car cabin 142 Signals: (a) Combined luminous hall buttons with LED hall position indicators at all floors (b) LED car position indicator panel of stainless steel (c) Car operating panel of stainless steel with luminous buttons in car (d) Car direction indicator in car & landing (e) Battery operated alarm bell & emergency light (rechargeable) along with suitable maintenance free battery. (The system shall be separate from ARD batteries.) (f) Overload warning feature in car cabin (display / announcing type both) (g) One firemans switch to be installed at ground floor near landing door. (h) All signal fixtures & car operating panel on hairline stainless steel face plate with hairline finish (j) Infrared door sensor safety edge of door for entire height. 143 Safety Device: (a) Automatic Rescue Device (ARD) / automatic landing device operating with maintenance-free batteries having suitable capacity. The batteries must have auto charging facilities. (b) The ARD actuation time shall be less than one second after failure of power supply and when ARD is operative the car shall stop at the nearest floor and then doors shall open. 144 Operation: Simplex, full collective automatic operation 145 Machine Room: Located above the hoist way, details as per building drawings 146 Hoist way: Construction details as per building drawings 147 Civil Work: Necessary civil work viz. making good disturbed surfaces, modification to landing space to suit car size, necessary foundation to machine(s), etc. 148 One number of wall mounted type telephone instrument installed inside of car cabin along with fixing arrangement and telephone cable of suitable size from car cabin to machine room run along with travelling cable. The telephone instrument shall be connected in the telephone DB installed in the machine room 149 Looking mirror of size 1200x900mm, 5.5mm thick to be provided on rear panel wall (opposite to main door) of car cabin above hand rail 150 Provision of suitable size of copper conductor XLPE insulated cable from Lift Panel installed at Ground floor to machine room will deemed to be included the rate quoted by the contractor 151 Subtotal 152 Lump sum price worked out by the tenderer for“EXCAVATION, EARTHWORK AND SITE DEVELOPMENT WORKS as listed in Schedule ‘A’ Section - XII 153 Schedule A Section -XIII (Furniture Works) 154 Almirah small steel as per drawing No. FD-1032 sheet No. 1/1 155 Book shelf open (large) steel as per drawing No. FD-69(M) sheet No. 1/1 156 Bed Hard as per drawing No. FD/E6/MAP/08(R) sheet No. 1/1 157 Chair Verandah as per drawing No. FD/E6/MAP/11 sheet No. 1/1 158 Charpoy folding IP with hard top as per drawing No. FD-388(R) sheet No 1/1 159 Peg Table as per drawing No. FD/MAP/11 sheet No. 1/1 160 Rack shoe steel as per drawing No. FD/E6/MAP/02(R) sheet No. 1/1 161 Table bed Side as per drawing No. FD/E6/MAP/15(R) sheet No. 1/1 162 Table Centre as per drawing No. FD/MAP/08 sheet No. 1/1 163 Dressing Table including Stool as per drawing No. FD/MAP-II/07 sheet Nos 1/2 & 2/2 164 Chair dining JCOs/Ors as per drawing No. FD/MAP-II/05 sheet No. 1/1 165 Chair easy per drawing No. FD-229 sheet No. 1/1 166 Chair writing as per drawing No. FD-280 sheet No. 1/1 167 Charpoy with hard top as per drawing No. FD/MAP-II/01 sheet No. 1/1 168 Mirror dressing(Gents) as per drawing No. FD/E6/MAP/16 sheet No. 1/1 169 Table dining 4 persons as per drawing No. FD/MAP-II/03 sheet No. 1/1 170 Table with drawer (900 mm X 600 mm X 760 mm) as per drawing No. FD-283 sheet No. 1/1 171 Chair School with hand board as per drawing No. FD/E6/MAP/05 sheet No. 1/1 172 Note:-Quantities of materials given on standard drawings are for guidance only. The contractor shall work out the quantities of materials required for each item of BOQ and quote his rate accordingly no claim shall be entertained on account of inaccuracy in the quantities of these materials and workman ship which shall be as specified in particular specifications and as approved. The drawing Nos mentioned in BOQ item No 184 to 264 shall form part of tender document which will not be attached with tender document. The tenderers are deemed to be in possession and conversant fully with the drawing shown in standard furniture designs including amendments published by AHQ, Engineer-in -Chief, New Delhi. For reference and guidance the tenderer may study and see these drawings in the any office ofGarrison Engineer in MES before quoting their rates. No claim shall be entertained regarding misinterpretation of the drawings at a later stage. 173 Subtotal 174 Lump sum price worked out by the tenderer for“ARBORICULTURE WORKS as listed in Schedule ‘A’ Section - XIV (Part-I) 175 Schedule A Section -XIV (Part-II) (ARBORICULTURE WORKS) 176 Material and labour for Grassing with Selection No.1 grass including enough watering and maintance of the lawn till the grass forms a thick lawn free from weeds and fit for moving including supplying good earth if needed including supplying and spreading of Neem oil cakes, manure or sludge and chemical required for preparation of the ground for plantation of grass complete all as specified and as directed. 177 Supply and planting of Hedge and Shrubbery (Anarmi, Ficus and the like) as directed by Engineer-in-Charge minimum 3 feet above GL including creation of beds by excavating 60 cm deep and 60 cm wide trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with Sludge or manure in the ratio 8:1 (8 Part of stacked volume of earth after reduction of 20 % with 1 part of stacked volume of sludge or manure ater reduction by 8%) flooding with water filling with earth if necessary, watering and finally fine dressing leveling etc including stacking and disposal of material declared unserviceable and surplus earth by spreading and leveling as directed within a lead 50 m and lift upto 1.50 m complete all as specified and as directed. 178 Supply and laying/fixing 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & lick compacted bed farce dory meinod using fu mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand;complete all as specified and as directed by Engineer-in-ChargeNote:- Tiles shall be approved by GE before incorporation in the work. 179 Material and labour for sand cushioning, with dry and clean tibba sand (for under ground cable) 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cablecomplete all as specified and as directed.Note:- (i) Punned thickness shall be considered for payment purpose (ii) Approved sand free from vegetations, grass and other deleterious substances shall be used. 180 Supply and laying factory made kerb stone of size 30x15x45cm of M-25 grade cement concrete laid in position to the required line, level and curvature, jointed with cement mortar (1:3) (1 cement:3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and as directed by Engineer-in-Charge 181 Supplying following plants in poly bags 0.25 m to 0.30m dia with height 1.20 m to 1.80 m including digging holes 1.20m dia x1.2m deep in ordinary soil and refilling the same with the excavated earth mixed with manure of approved quality or sludge in ratio 2:1(2 parts of stacked volume of earth after reduction of 20% with 1 part of stacked volume of sludgeor manure after reduction by 8%) flooding with water and removal of surplus soil, with & including antitermite treatment using suitable chemicals or pesticides of approved quality, as required and making Thaola all as specified and as directed by Engineer-in-charge.Note :- Contractor shall maintain the trees till physical completion of contract.Unit rate quoted is inclusive of replacement of dead trees,manures and all fertilizers mentioned above is inclusive in rate quoted. 182 Neem Tree. 183 Canerydate Palm 184 Gulmohar 185 Fruit Bearing Trees 186 Plumeria 187 Supplying plants Flower like Ticoma, rose,motia, Chandni, lxora, marigold rose, vinca (any colour) as directed of height not less than 0.60m above GL including digging holes 1.20m dia x1.2m deep in ordinary soil and refilling the same with the excavated earth mixed with manure of approved quality or sludge in ratio 3:1(One part of manure & 3 part of soil) manure 200 gm per plant ,flooding with water and removal of surplus soil n.exc 1.50 Km and depositing where directed with & including using suitable chemicals or pesticides of approved quality, as required and making Thaola all as specified and as directed by Engineer-in-charge.Note :- Contractor shall maintain the trees till physical completion of contract.Unit rate quoted is inclusive of replacement of dead trees,manures and all fertilizers mentioned above is inclusive in rate quoted. 188 Supply and Fixing precast RCC 1:1.5:3 Type A1 lawn bench and backsupport of size 1.50 x 0.60m of maximum three person seating capacity supporting precast RCC type A1 for back and base with including assemble the precast member with suitable nutt & bolt and placing and anchoring with hold fast 350mm - 16mm dia MS bar on concrete base (size 1.20x0.60m for each support) with 100mm thick PCC 1:2:4 Type B1 over 150mm thick sub base PCC 1:4:8 type D2 complete all as specified and as directed by Engineer-in charge 189 Subtotal 190 Schedule A Section -XV ( Maintance) 191 Material and labour for the plants/hedge/grass by weeding, hosing, saucer making once in every month for plants/hedge, once in every 15 days for carpet grass/country grass/doob grass, bermuda grass, pruning dired ranches once in every week, depositing the material at place of dead plants of same species and height turning with dods whenever required by replacing the dead patches of grass of any type with same grass as required without any extra cost to the department all as specified and as directed. (plants of various species -678 Nos (approx), Hedge and shruery - 520 RM (approx) and Grass - 4000 sqm( approx) 192 Subtotal
|
