|
Tender For Construction Of Foot Path And Beautification Of Bhoor Chauraha, Bulandshahr - Dismantling of flexible pavements and disposal of dismantled materials upto a lead of 100 m, stacking serviceable and unserviceable materials separately as per Technical Specification Clause 202 Bituminous CoursesSOR/2022/17.19 2 Providing and laying cement concrete in 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) and curing complete, including cost of form work. In Foundation and floors.SOR 2022 (281) 3 R.C.C. work withCement approved coarse sand and 2 cms gauge approved stone ballast in the proportions of 1:1.5:3 in raftsfoundation and footing excluding supply of reinforcment and its binding the same with 24 BWGGI wire and including necessary centring and shuttering etc. and also including supply of all materials, labour and T&P etc 287reuired for proper completion of the work excluding cost of binding wire.SOR / 287a/2022 4 R.C.C. work withCement approved coarse sand and 2 cms gauge approved stone ballast in the proportions of 1:1.5:3 in Wall , Column excluding supply of reinforcment and its binding the same with 24 BWGGI wire and including necessary centring and shuttering etc. and also including supply of all materials, labour and T&P etc 287reuired for proper completion of the work excluding cost of binding wire.SOR / 289/2022 5 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. (a) Mild steel and Medium Tensile steel bars. DSR2023(5.22.1) 6 Providing and laying cement concrete in 1:2:4 of not less than strength of M-150 Stone ballast (20 mm nominal size) approved coarse sand and cement, curing complete, Including cost of form work. In Foundation and floors. Sor 2023 (279 a) 7 Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : 8 DSR 2023 ( 8.14.1.5 ) 30 mm thick 9 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 ( 1cement : 5 coarse sand) with joints finished flush. 10 Red sand stone DSR/2023/11.28.1 11 Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. 12 Fastener with threaded dia 12 mm. DSR /2023/8.8.1.2 13 Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).DSR2023/16.75 14 Applying stamping finish to the top surface of freshly laid plain/reinforced cement concrete of specified grade in porticos, sidewalks, driveways, pool decks and open yards as per direction of the Engineerin-Charge. The process shall include the following:-DSR-2021(26.83) 15 The concrete shall be placed and screeded to the finished grade, and floated to a uniform surface by using standard finishing techniques. The approved color hardener @ 2.7 kg/sqm shall be applied evenly to the surface of the fresh concrete by the dry shake method by sprinkling in two or more shakes, floated after each shake and trowelled only after the final floating. The approved release agent @ 0.113 kg/sqm shall be applied evenly to the trowelled surface before stamping or the said release agent can be applied to the flexible polyurethane stamp moulds of approved design and in required sizes to achieve final stamped pattern. These stampings shall be placed on the surface of concrete in three to four pieces at a time and tapped gently with rammers of sufficient size & weight to leave proper stamp marks and the process repeated for the remaining concrete surface till the whole surface to be stamped is completed within the time while concrete is in plastic stage of setting. 16 The construction joints shall be provided by groove cutting of size 4mm x 20mm in panel size 3m x 3 m or lesser as per the site conditions and filling the same with 10 mm baker rod and providing and laying (PU) Polyurethane based joint sealer of approved make as per manufacturer’s specifications and finished by applying Polyurethane resin based top protective clear coat of minimum 80 micron applied with rollers on properly cured and dry clean surface. (Cost of concrete for flooring is not included in this item which shall be paid separately.) 17 Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 18 Hot finished seamless type tubes. DSR/2023/10.16.2 19 Painting two coat over priming coat (but excluding cost of priming coat) on steel and other metal surfaces upto 10cm width or girth or small articles not exceeding 0.10 Sq.M. in area with superior synthetic enamel such as Luxol 3, Hi gloss Apcolite, Superlac, Dulux specified brushing to give and even shade and including the cleaning the surface of all dirt, dust and other foreign matter sand papering and scrapping including cost of all materials, labour, tools and plants etc. required for proper completion of work. (CH-15 Item No. 641 a +642SOR 2022) 20 Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35-2015 The finished surface to be level, uniform and free from streaks and holes. SOR 2022/ 22.3/MORTH 803(8.13) 21 Class-150 (Non Modular) brick work in 1:4 cement and Coarse sandmortar in foundation and plinth including supply of all materials, labour and T&P etc. required for proper completion of the work. (305aSOR 2023) 22 12mm thick Cement plaster 1 cement : 4 Coarse sand in single coat of fair side of single of half brick wall for interior plastering upto floor two level including internal rounded angles chamfers, and/or rounded angles not exceeding 80mm. In girth and finished even and smooth No. extra for mixing any additive. ( 584 SOR 2023) 23 (28) P.V.C. pipe 110mm dia I.S.I. Make(working presure 6kg/sqcm) 24 Supply and fixing of Skuplture as per given design and specification complete approved by E/I 25 Providing and laying gang saw cut 18 mm thick, mirror polished pre-moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge. DSR2023/16.86 26 With granite stone of area less than 0.50 sqm.
|
