Tender For Annual Stage Contract For Maintenance, Repair And Renovation Of Dc Office Complex Within The Amar ... in India

Work Detail

Annual Stage Contract For Maintenance, Repair And Renovation Of Dc Office Complex Within The Amar Niwas Premises At Tankipor- 1 Supply of labours. 2 Mazdoor. 3 Carpenter 1st class. 4 Carpenter 2nd class 5 Mason 1st class. 6 Mason 2nd class. 7 Plumber. 8 Black Smith. 9 Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: All kinds of soil : 1 meter from cutting edge 10 Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil : 11 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. 12 Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soil. 13 Pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like. 14 Removal of unhygienic materials (so classified by the site engineer) from designated sites and its disposal as per directions, all inclusive. 15 Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared. 16 Providing & laying of stone soling hand packed in foundation and plinth incl ramming, watering, compaction & lead lifts all carriages upto site of work complete. 17 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 18 1:1½:3 (1 cement :1½ coarse sand: 3 graded stone aggregate 20 mm nominal size) 19 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 20 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) 21 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 22 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) 23 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) 24 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) 25 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts,struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etcupto floor V level, including curing but excluding the cost of centring, shuttering and finishing with. 26 1:1½:3 (1 cement :1½ coarse sand: 3 graded stone aggregate 20 mm nominal size) 27 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 28 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 29 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) 30 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) 31 1:5:10 (1 cement : 5 coarse sand : 10 graded brick aggregate 40 mm nominal size 32 Providing & laying damp-proof Course 40 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone agg 12.5 mm nominal size) and curing complete 33 Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete 34 Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 35 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) 36 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 37 Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) 38 Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) 39 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete Thermo-Mechanically Treated bars of grade Fe-500D or more. 40 Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 41 Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded 42 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes 43 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. Fixed to steel windows by welding 44 Centering and shuttering including strutting, propping etc. and removal of form for: 45 Foundations, footings, bases of columns etc. for mass concrete. 46 Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. 47 Suspended floors, roofs, landings, balconies and access platforms. 48 Shelves (cast-in-situ) 49 Lintel, beams, plinth beams, girders, bressumers and cantilevers. 50 Columns, pillars, piers, abutments, posts and struts. 51 Stairs (excluding landings) except spiral staircases. 52 Spiral staircases (including landings) 53 Arches, domes, vaults upto 6 m span 54 Edges of slabs and breaks in floors and walls 55 Under 20 cm wide 56 Above 20 cm wide 57 Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand) 58 Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level 59 Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in 60 Cement mortar 1:3 ( 1 cement : 3 coarse sand) 61 Cement mortar 1:4 ( 1 cement : 4 coarse sand) 62 Extra for half Brick masonry in superstructure above plinth level upto floor V level. 63 Dry random rubble masonry with hard stone in foundation and plinth With bond stone. (Quarry) 64 Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels 65 Raj Nagar plain white marble/Udaipur green marble/zebra black marble (16mm) 66 (Area of slab upto 0.5 sqm) 67 (Area of slab over 0.5 sqm) 68 Granite of any colour or shade (18mm) 69 (Area of slab upto 0.5 sqm) 70 (Area of slab over 0.5 sqm) 71 Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 72 Marble Work 73 Granite Work 74 Extra for fixing marble / granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete 75 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): First class deodar wood 76 Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position 77 Budloo / Fir wood 78 Providing hoisting and fixing trusses/purlins /rafters/posts/ post-plates or like components including cost of screws etc. completePopular Wood 79 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia wire and 1.4 mm wide aperture with matching wood beading 80 Providing and fixing plain jaffri of 35x10 mm laths placed 35 mm apart (frames to be paid separately) including fixing 50x12 mm beading complete with First class kail wood. 81 Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 82 25mm thick with 12.5 mm nominal size stone aggregate. 83 40mm thick with 20 mm nominal size stone aggregate. 84 50 mm thick with 20mm nominal size stone aggregate. 85 Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, cleaning and curing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) . Light shade using white cemen 86 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 87 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete 88 Size of tile 600x600 mm 89 Size of tile 1000x1000 mm 90 Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). 91 Size of tile 600x600 mm 92 Size of tile 1000x1000 mm 93 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. 94 Size of tile 600x600 mm 95 Size of tile 1000x1000 mm 96 Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete 97 Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalization or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metallic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanized with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bimetallic contacts all complete required to perform as per specification and drawing The item includes cost of all material &labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, fieldtests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. 98 Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required 99 0.63 mm thick with zinc coating not less than 275 gram/m2 100 0.50 mm thick with zinc coating not less than 275 gram/m2 101 Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 102 0.63 mm thick with zinc coating not less than 275 gram/m2 103 0.50 mm thick with zinc coating not less than 275 gram/m2 104 Providing valleys of 90cm wide overall in plain G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G.I.limpet and bitumen washers complete. 105 1.60 mm thick with zinc coating not less than 350 gram/m2 106 1.25 mm thick with zinc coating not less than 350 gram/m2 107 1.00 mm thick with zinc coating not less than 275 gram/m2 108 Providing and fixing 15cm wide 45 cm overall semi circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc. including making necessary connections with rain water pipes complete. 109 0.80 mm thick with zinc coating not less than 275 gram/m2 110 0.63 mm thick with zinc coating not less than 275 gram/m2 111 Providing and fixing UV stabilized fiberglass reinforced plastic sheet roofing upto any pitch including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts and nuts 8mm dia. G.I plain/ bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% Ultra-violet stabilizer in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS: 10192 and IS: 12866. The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 112 2mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6") as specified. 113 2mm thick flat 114 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 115 In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete. 116 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. 117 Providing and fixing of KHATAM BANDI ceiling of first class budloo/fir wood excluding the cost of frame work which is to be paid separately. 118 Changez Khani 119 Chaar Gul 120 Chaar Phool 121 Pahal Gardan 122 Dawaz-dal-i-girde 123 Paanch Murabah 124 12mm Cement plaster of mix 125 1 : 4 ( 1 cement : 4 fine sand) 126 1 : 6 ( 1 cement : 6 fine sand) 127 15mm Cement plaster on the rough side of single or half brick wall of mix 128 1 : 4 ( 1 cement : 4 fine sand) 129 1 : 6 ( 1 cement : 6 fine sand) 130 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand) 131 20mm Cement plaster of mix: 132 1 : 4 ( 1 cement : 4 fine sand) 133 1 : 6 ( 1 cement : 6 fine sand) 134 Pointing on stone work with cement mortar 1 : 3 (1 cement : 3 fine sand) 135 Flush/Ruled Pointing 136 Raised and cut pointing 137 White washing with lime to give an even shade on New Work (three or more coats) 138 Colour washing such as green blue or buff to give an even shade 139 New work (two or more coats) with a basecoat of white washing with lime. 140 New work (two or more coats) with basecoat of whiting 141 Distempering with dry distemper of approved brand and manufacture (two or more coats) and of required shade on new work, over and including water thinnable priming coat to give an even shade 142 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer 143 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre,two or more coats on new work of approved manufacturer, of required shade and colour complete as per manufacturer"s specifications 144 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface. 145 Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm) 146 Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm 147 Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm) 148 Finishing wall with premium acrylic smooth exterior paint with silicone additives of required shade on New work (two or more coats applied @ 1.43 liter/10sqm over and including priming coat of water exterior paint applied @ 2.20kg/10sqm) 149 Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers" specifications: 150 Two or more coats applied @ 1.25 liter/10sqm over and including one coat of special primer applied @ 0.75liter /10sqm 151 Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacture 152 Painting steel work with deluxe multi surface paint of required shade to give an even shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.80litre/10sqm of approved brand and manufacture 153 Applying priming coat: 154 With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) 155 With ready mixed aluminum primer of approved brand and manufacture on resinous wood and ply wood 156 With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanized iron/steel works 157 With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel work (second coat) 158 Painting with silicon and acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces: 159 One coat 160 Two coats 161 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer"s specifications including appropriate priming coat, preparation of surface, etc complete 162 On steel work 163 On concrete work 164 Painting on G.S sheets with synthetic enamel paint of approved band and manufacture of required colour to give an even shade on New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution. 165 Applying a coat of mordant solution on G.S. sheets: 166 With a solution of 38gms of copper acetate in liter of soft water 167 With a solution made of 13gms of hydrochloric acid in a solution of 13gms each of copper chloride, copper nitrate and ammonium chloride dissolved in a liter of soft water. 168 Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with black anticorrosive bitumastic paint of approved brand and manufacture over and including a priming coat of ready mixed zinc chromate yellow primer on new work. 169 75 mm diameter pipe 170 100 mm diameter pipe 171 150 mm diameter pipe 172 Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with aluminum paint of approved brand and manufacture over a priming coat of ready mixed zinc chromate yellow primer on new work. 173 75 mm diameter pipe 174 100 mm diameter pipe 175 150 mm diameter pipe 176 Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work : 177 100 mm diameter pipe 178 150 mm diameter pipe 179 Painting with oil type wood preservative of approved brand and manufacture on New work (two or more coats) 180 Providing and applying two coats of fire retardant paint on cleaned wood/ply surface @ 3.5sqm per liter per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant 181 Coal tarring two coats on new work using 0.16 liter and 0.12 liter coal tar per sqm in the 1st coat and 2nd coat respectively 182 Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work 183 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. 184 Two or more coats on new work 185 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. 186 Painting with aluminum paint of approved brand and manufacture to give an even shade. Two or more coats on new work 187 Painting with acid proof paint of approved brand and manufacture of required colour to give an even shade. Two or more coats on new work 188 Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade on new work Two or more coats. 189 Floor painting with floor enamel paint of approved brand and manufacture of required colour to give an even shade on new work Two or more coats. 190 Varnishing with varnish of approved brand and manufacture: 191 Two or more coats of glue sizing with copal varnish over and under coat of flatting varnish. 192 Two or more coats of glue sizing with spar varnish on an under coat of flatting varnish 193 French spirit polishing, Two or more coats on new works including a coat of wood filler 194 Polishing on wood work with ready mixed wax polish of approved brand and manufacture on New work 195 Floor polishing on masonry or concrete floors with wax polish of approved brand and manufacture 196 Lettering with black Japan paint of approved brand and manufacture. 197 Washed stone grit plaster on exterior walls of height upto 10 m above ground level in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2kg of cement per m2, top layer 15mm cement plaster 1:1/2 :2 (1 cement: 1/2 coarse sand : 2 stone chippings 10mm nominal size), in panels with groove all around as per approved pattern including scrubbing and washing the top layer with brushes and water to expose the stone chippings, complete as per specification and direction of Engineer-in -charge (payment for providing grooves shall be made separately). 198 Forming groove of uniform size in the top layer of washed stone gritplaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge : 199 15 mm wide and 15 mm deep groove 200 20 mm wide and 15 mm deep groove 201 Extra for washed grit plaster on exterior walls of height more than 10m ground level for every additional height of 3m or part thereof 202 Extra for washed stone grit plaster on circular work not exceeding 6m in radius (in two coats) 203 Forming groove of uniform size from 12x12 mm and upto 25x15 mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications and direction of the Engineer in- Charge. 204 Extra for using white cement in place of ordinary cement in the top layer of the item of washed stone grit plaster 205 Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 206 1 mm thick 207 2 mm thick 208 Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. 209 One coat 210 Two coats 211 Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. 212 One coat 213 Two coats 214 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ liter of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. 215 One coat 216 Two coats 217 Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. 218 With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ liter 219 With ready mixed red oxide zinc chromatic on steel / iron works having VOC content less than 250 grams/ liter 220 With water thinnable cement primer on wall surface having VOC content less than 50 grams/liter 221 Finishing walls with 100% Premium acrylic emulsion paint havingVOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/10 sqm. Over & including priming coat of exterior primer applied @ 0.90 litre/10 sqm. 222 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 223 Distempering with dry distemper of approved brand and manufacture (one or more coats) and of required shade on old work to give an even shade. 224 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 225 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work. 226 Painting with aluminum paint of approved brand and manufacture to give an even shade, one or more coats on old work. 227 Painting with acid proof paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work. 228 Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade, one or more coats on old work 229 French spirit polishing, one or more coats on old work 230 Polishing on wood work with readymade wax polish of approved brand and manufacture on old work. 231 Re-lettering with black Japan paint of approved brand and manufacture. 232 Painting (one or more coats) with black Japan paint of approved brand and manufacture to give an even shade. 233 Providing and fixing C.P. brass chain and rubber plug complete for sink or wash basin : 234 32 mm dia. 235 40 mm dia. 236 Distempering with 1st quality Acrylic/oil bound washable distemper (ready-made) having VOC content less than 50 grams/litre of approved manufacturer and of required shade and colour complete as per manufacturers’ specifications, one or more coats on old work 237 Finishing walls with water proofing cement paint of required shade: 238 Old work (one or more coats applied @ 2.20 kg/10sqm) over priming coat of primer applied @ 0.80 liters/10sqm complete including cost of priming coat. 239 Old work (one or more coats applied @ 2.20 kg/10sqm) complete 240 Finishing walls with textured exterior paint of required shade: 241 Old work (two or more coats on existing cement paint surface applied @ 3.28 ltr/10sqm) 242 Old work (one or more coats) applied @1.82 ltr/10sqm 243 Finishing walls with Acrylic smooth exterior paint of required shade: 244 Old work (two or more coats applied @ 1.67 liters/10sqm on existing cement paint surface) 245 Old work (one or more coats applied @ 0.90 liters/ 10sqm) 246 Finishing walls with premium Acrylic smooth exterior paint with silicon additives of required shade: 247 Old work (Two or more coats applied @ 1.43 liters/ 10 sqm) over existing cement paint surface. 248 Old work (one or more coats applied @ 0.83 liters/ 10sqm) 249 Varnishing with varnish of approved brand and manufacture: 250 One or more coats with copal varnish. 251 One or more coats with spar varnish. 252 Melamine polishing on wood work (one or more coats) 253 Varnishing with flatting varnish of approved brand and manufacture one or more coats on old work 254 Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 meters lead 255 With cement mortar 1:4 (1 cement : 4 fine sand) 256 With cement mortar 1:4 (1 cement : 4 coarse sand) 257 Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding holdfasts in cement concrete blocks of size 15x10x10cm with cement concrete 1:3:6 (1 cement :3 coarse sand: 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground within 50 meters lead: 258 Door chowkhats 259 Window chowkhats 260 Clerestory window chowkhats 261 Fixing chowkhat in existing opening in brick/RCC wall with dash fasteners/chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhats and 2 nos. on each vertical member of window chowkhats), including cost of dash fasteners/chemical fasteners. 262 Making the opening for door/window/clerestory window in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground. 263 Renewing glass panes, with putty and nails wherever necessary including raking out old putty : 264 Float glass panes of thickness 4.0 mm(weight not less than 10kg/sqm) 265 Float glass panes of thickness 5.0 mm(weight not less than 12.5 kg/sqm) 266 Renewing glass panes, with wooden fillets wherever necessary : 267 Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm) 268 Float glass panes of thickness 5.0 mm (weight not less than 12.5 kg/sqm) 269 Renewing glass panes and re-fixing existing wooden fillets: 270 Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm) 271 Float glass panes of thickness 5.0 mm (weight not less than 12.5 kg/sqm) 272 Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge. 273 Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge. 274 Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer-in-Charge. (a) Internal Work- Exposed on wall 275 Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. 276 Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge: 277 1:3:6 or richer mix (i/c equivalent design mix) 278 1:4:8 or leaner mix (i/c equivalent design mix) 279 Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: In cement mortar 280 Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m. (stacks of cleaned bricks shall be measured) From brick work in cement mortar 281 .Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 meters lead 282 Of area of 3 sqm. and below 283 Of area beyond 3 sqm. 284 Dismantling steel work in single sections including dismembering and stacking within 50 meters lead inR.S. Joists 285 Dismantling wood work in frames, trusses, purlins and rafters upto 10 meters span and 5 meters height including stacking the material within 50 meters lead. 286 Of sectional area 40 sqcm. and above. 287 Of sectional area below 40 sqcm. 288 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead. 289 For thickness of tiles 10 mm to 25 mm 290 Demolishing RCC work by mechanical means & stockpiling at designated locations & disposal of dismantled materials upto a lead of 1 kilometer, stacking serviceable & unserviceable material separately including cutting reinforcement bars 291 Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets 292 20 mm dia ( heavy type) 293 25 mm dia ( heavy type) 294 Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts 295 Painting road surface marking with adequate no. of coats to give uniform finish with read mixed road marking paint conforming to IS: 164, on bituminous surface in white/yellow shade including cleaning the surface of all dirt, scales, oil, grease and foreign material etc. complete. 296 New work (Two or more coats) 297 Old work ( One or more coats) 298 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). 299 Providing and fixing tiled False Ceiling of specified materials of size 595x595mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms/sqm both side inclusive ) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200 x 600mm and secondary cross “T” of length 600mm and size 24x25 mm made of 0.30mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.30mm and laying false ceiling tiles of approved texture in the grid including, wherever, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27x37x 25x1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanized butterfly level clips of size 85x30x0.8 mm spaced at 1200mm center to center along size 85x30x0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. (The rate is excluding the cost of tiles which will be paid for separately). 300 GI Metal Ceiling Lay in plain Tegular edge Global white colour tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. 301 Providing and laying chisel dressed Devri Stone of size 300x200 mm face with 150 mm depth in cement mortar 1: 6 (1 cement : 6 coarse sand) upto plinth level including curing. One face dressed 302 Fine chisel dressed 303 Rough chisel dressed 304 Extra for fine chisel dressed Devri Stone in square or rectangular Pillars 305 Providing and laying rough chisel dressed Devri Stone in kerbs, of size 200x200 mm face with chamfer in cement mortar 1: 6 (1 cement : 6 coarse sand) including curing. 306 Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately). imported kail wood: (35mm Thick) 307 Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge (35mm Thick) 308 Providing and fixing wire gauze using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows including cost of beading complete. 309 Providing and fixing of chicken mesh wherever required of specified size including cost of beading and nails complete. 310 Providing and fixing 30-35 mm thick paneled door shutters, including ISI marked black enameled M.S. butt hinges with necessary screws including paneling of 12mm thick laminated board both sides laminated as per the approved design complete with required beading/moldings. (styles and rails shall be of standard size) in fittings imported kail wood: 311 Providing and fixing 30-35 mm thick paneled door shutters, including ISI marked black enameled M.S. butt hinges with necessary screws including cost of 25-30mm thick paneling of approved design with required beading/moldings. imported kail wood: 312 Providing and fixing 30-35 mm thick paneled/ flush door shutters, including ISI marked black enameled M.S. butt hinges with necessary screws Readymade ornamental modular, factory manufactured machine made of hard wood teak finished, of approved quality, color and shade. 313 Providing and fixing 35 mm thick paneled door shutters with wood carved panels (Carving on one side) including polishing, and ISI marked black enameled M.S. butt hinges with necessary screws as per the approved designcomplete with required beading/moldings. (styles and rails shall be of standard size) imported kail wood: 314 Providing and fixing 32 mm thick paneled door shutters with wood carved panels (Carving on both sides) including polishing, and ISI marked black enameled M.S. butt hinges with necessary screws as per the approved designcomplete with required beading/moldings. (styles and rails shall be of standard size) imported kail wood: 315 Providing and fixing of wooden paneling/ lining of 12mm (net thickness) including providing and fixing of ground frame work (50x25mm or as specified) of first class Budloo wood/ 19mm ply including cost of screws, wooden plugs etc. complete as per directions of EIC 316 Made from imported wood 317 Made from Budloo wood 318 Providing and fixing of ply wood including cost of nails adhesive etc. complete at all places. 319 4 mm thick 320 6 mm thick 321 12 mm thick 322 19 mm thick 323 Providing and fixing of single side laminated ply wood including cost of nails adhesive etc. complete at all places. 324 6 mm thick 325 12 mm thick 326 18-19 mm thick 327 Providing and fixing of 19mm thick commercial block board at all places including cost of nails and adhesive complete. Thickness/ Pattern/ Design to be approved by EIC 328 Providing and fixing of Dulmica/ sun mica sheeting including cost of nails and adhesive complete. 329 0.8-1 mm thick for lining 330 0.4-0.5mm thick for lining 331 Providing and fixing wood work in fencing that is in planks of the following nominal size excluding cost of posts and runners. 1st class Budloo wood. (ornamental) 332 20 mm thick. 333 25 mm thick. 334 35 mm thick. 335 Providing and fixing of ornamental cornice of following size. 1st class budloo/imported wood. 336 40-50 mm 337 65 mm 338 75 mm 339 Providing and fixing of PVC edge beading 340 12 mm 341 19 mm 342 25 mm 343 Providing and fixing 20mm thick overlapped weather boarding in soffits of 1st class imported wood including applying priming coat of approved quality primer. 344 Providing and fixing of planed eaves boarding 250mm x 30mm size of 1st Class imported wood. 345 Providing and fixing of planed eaves boarding 250mm x 30mm size of 1st Class Budloo wood. 346 Providing and fixing of wooden beading ornamental 25mmx6mm size of Budloo wood. 347 Providing and fixing of reflective glass panes 3.5 mm thick in doors windows and clearstory windows including cost of budloo wood beading of required size. 348 Providing and fixing of Buj tile cladding of required pattern. Shade and design over 20mm thick cement plaster 1:3 mix (1 cement: 3coarse sand) including jointing with neat cement slurry complete. 349 Providing and fixing of Interlocking/Chequered precast cement concrete tiles colored(rubber finish) in foot paths & courtyards jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and cleaning etc. complete on 20mm thick layer of dry sand . 350 40mm thick. 351 50mm thick. 352 75mm thick. 353 Providing and fixing A.C.P 3mm multi coloured (Fire retardant) in partitions, ceilings, shutters frames etc in panels of min size 600mm x 600mmincluding cost of rubber,neoprene gasket ,waterproof silicon sealent , or as required at site as per the directions of concerned engineer in charge.complete job 354 Providing and laying G.S.B. grade including compacting, ramming, watering and carriage complete. (Hand ramming in plinth or rooms) 355 Engagement of tipper including fuel charges complete. 356 Engagement of excavator (JCB) in all terrains including fuel charges complete. 357 Engagement of hand cart all complete 358 Providing and fixing of wardrobe, almirah, drawer locks(Sample to be approved by EIC) 359 Providing and fixing of aluminum double channel with wheel set for sliding glass window of approved quality of following sizes. 360 20 mm 361 25 mm 362 Providing and fixing of door closer capsule type of standard make 363 Providing and fixing of door closer springtype of standard make 364 Providing and fixing of following fittings 365 Aldrop 366 Tower Bolt 100mm 367 Tower Bolt 150mm 368 Handle 100mm 369 Handle 150mm 370 I Hook 371 Hinges 75mm 372 Hinges 100mm 373 Lockable sliding Aldrop 250-300mm long (Godrej/ Link/Ramson or equivalent) 374 Providing and fabrication of ward robes (ornamental) of approved quality 19mm Ply board in sides, shelves and wherever required including 6mm ply wood on back and 19MM ply boardin shutters, inside and outside of shutters finished with Dulmica sheeting of approved quality and color on exposed face of approved design and drawings including (painting two or more coats of synthetic enamel paint of approved quality and color inside) including cost of following aluminum fittings and locks of approved make. 15mm dia. M.S. pipe chromium plated with necessary brackets 4"-0" length and including all other necessary accessories complete in all respects. Including fixing with dashfasteners wherever required (For payments front face to be measured). 375 50-60 cm deep 376 40-45 cm deep 377 20-30 cm deep 378 extra for using ply to ply instead of board (Face measurement) 379 extra for using lining instead of painting on internal surface as per measurement - 12mm 380 Extra for using 10-12mm ply instead of 6mm on back side of Wardrobe/ Kitchen cabinets 381 Extra for using MDF shuttes ornamental type of required thickness instead of ply/ pine shutters (Face measurement) 382 Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. 383 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid. 384 Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C automatic flushing cistern, with fittings, standard size G.I./ PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and in C.P brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required:Range of three squatting plates with 10 liter P.V.C. automatic flushing cistern. 385 Providing and fixing wash basinwith CI/MS/ brackets including painting of fittings and brackets, cutting and making good walls wherever required white vitreous china wash basin size 630x450mm with32mm dia. C.P. brass union & flexible waste pipe(Jaquar/ Hindware/ Cera/ Kerrovit or equivalent) 386 Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. 387 Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS: 7231,with fittings and fixtures complete. 10 liters capacity- white(Sample to be approved by EIC) 388 Providing and fixing solid plastic seat with lid for pedestal type W.C. pancomplete.(Sample to be approved by EIC) 389 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265mm size respectively. 390 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 610x460mm bowl depth 200mm 391 Providing and fixing white vitreous china laboratory sink including making all connections excluding cost of fittings Size 600x450x200 mm. 392 Providing and fixing of white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm respectively with automatic flushing cistern with standard flush pipe and C.P brass spreaders with brass unions and G.I clamps complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required One urinal basin with 5 liter white PVC automatic flushing cistern(Sample to be approved by EIC) 393 Providing and fixing of C.P grating 100mm size. ISI 394 Providing and fixing of G.I pipes (class B pipes) complete with G.I fittings and clamps including cutting and making good the walls etc. internal work (Exposed on Walls)(Sample to be approved by EIC) 395 15mm dia. Nominal bore 396 20mm dia. Nominal bore 397 25mm dia. Nominal bore 398 32mm dia. Nominal bore 399 40mm dia. Nominal bore 400 50mm dia. Nominal bore 401 Providing and fixing of G.I pipes (class B pipes) complete with G.I fittings excluding trenching and refilling etc. (external work)(Sample to be approved by EIC) 402 15mm dia. Nominal bore 403 20mm dia. Nominal bore 404 25mm dia. Nominal bore 405 32mm dia. Nominal bore 406 40mm dia. Nominal bore 407 50mm dia. Nominal bore 408 65mm dia. Nominal bore 409 80mm dia. Nominal bore 410 100mm dia. Nominal bore 411 Providing and fixing of following G.I. fittings. 15 mm nominal bore.(Sample to be approved by EIC) 412 Elbow 413 Tee 414 Union 415 pvc plug/ G.I Plug 416 Nipple 417 50mm long. 418 75mm long 419 100mm long 420 150mm long 421 Socket 422 15mm 423 20mm 424 25mm 425 Reducer 426 15mm-20mm 427 20mm-25mm 428 20mm-32mm 429 25mm-32mm 430 Providing and fixing of following G.I. fittings. 20 mm nominal bore.(Sample to be approved by EIC) 431 Elbow 432 Tee 433 Union 434 pvc plug/ G.I Plug 435 Nipple 436 50mm long. 437 75mm long 438 100mm long 439 150mm long 440 Providing and fixing of PVC connection with C.P. brass unions 441 300mm long. 442 450mm long 443 600mm long 444 Providing and fixing ball valve (brass) of approved quality complete (Sample to be approved by EIC) 445 15mm dia. 446 20mm dia. 447 25mm dia. 448 40mm dia. 449 Providing and fixing gate valve (brass) of approved quality complete (Sample to be approved by EIC) 450 15mm dia. 451 20mm dia. 452 25mm dia. 453 40mm dia. 454 50mm dia. 455 Providing and fixing of Ball cock of approved quality and make with plastic float. (PVC type) 456 15 mm 457 20 mm 458 Providing and fixing of flexible PVC Pipe 459 For Washbasin 460 For Urinal 461 Providing and fixing of Ball cock of approved quality and make without plastic float. 462 15 mm 463 20 mm 464 Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 465 Construction of plateform for W.C. with brick masonry in cement mortar 1:6 mix. Including filling of sand and providing of 15mm cement plaster in 1:4 mix. Complete job of size as directed at site 466 Providing and fixing of C.P. Cups for C.P. fittings. 467 Providing and fixing of C.I. manhole cover heavy duty of following sizes. 468 12"x12" 469 18"x18" 470 24"X24" 471 Providing , installation, commissioning and testing Hot water Geyzer of approved make including fixing with bolts/ fasteners/PVC connection etc. Venus, Recold, Hindware, Havells, Jaquar, Crompton of required capacity fittings and fixtures all complete wherever required in the course of completion. complete job. 472 50 Litre 473 35 Litre 474 25 Litre 475 Providing and fixing of PVC connection for wash basins, geysers etc. 476 30-45 cm in length 477 60-90 cm in length 478 Providing and fixing Geyser elements (as per Geyser type) dry/ wet 479 Providing and fixing Geyser thermostat 480 Providing and fixing Drain plug with washer. 481 Providing and fixing Safety valve for geysers. 482 Providing and fixing water washers for geysers. 483 Providing and fixing of auto thermo cut for geyser. 484 Providing and fixing of pressure water ball Valve 485 Providing and fixing C.P. brass bib cock of approved quality (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) 15mm nominal bore with flange 486 Short Body 487 Long Body 488 Providing and fixing of 15mm size chromium plated cast brass pillar cock of approved quality(Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) 489 Providing and fixing of 15mm size chromium plated cast brass angle valve of approved quality (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) with wall flange 490 Providing and fixing of 15mm size chromium plated cast brass wash basin mixer as menioned below (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) 491 Pillar Type 2 Knobs 492 Pillar Type Single Lever 493 Wall Mounted type 494 Providing and fixing of 15mm size chromium plated cast brass sink mixer Wall mounted/ Counter mounted of approved quality.(Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) 495 Providing and fixing of hand shower with chain of approved quality.(Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) 496 Providing and fixing of shower including shower arm of approved quality (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) withflange 497 Providing and fixing of 15mm size chromium plated cast brass wall mixer Non telephonicof approved quality. (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) withflange 498 Providing and fixing of 15mm size chromium plated cast brass wall mixer with bend pipe for head showerof approved quality. (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) withflange 499 Providing and fixing Towel ring 30mm. (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent)withflange 500 Providing and fixing Towel rod (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) 600mm long 501 Providing and fixing Soap Dish case 502 Providing and fixingToilet Paper Holder 503 Providing and fixing 600x120x5mm glass shelf with edges round off supported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete 504 Providing and fixing of pvc manhole cover of approved make of following sizes. (Heavy type) 505 12"x12" 506 18"x18" 507 24"X24" 508 Construct brick masonry man hole in cement mortar 1:4 (1 cement: 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 Coarse sand : 4 graded stone aggregate 20mm nominal size) foundation concrete (1:4:8) inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cementand making channel in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal sizefinished witha floating coat of neat cement complete. (Depth as per site requirement) 509 Size 90 x 90 cm deep including RCC/C.I. manhole cover medium duty with frame of size 60x60mm size/ Concrete Slab. With F.P.S. bricks with class designation 75 and with crushed stone aggregate complete in all respects. 510 Size 60 x 60 cm deep including RCC/C.I. manhole cover medium duty with frame of size 60x60mm size/ Concrete Slab. With F.P.S. bricks with class designation 75 and with crushed stone aggregate complete in all respects. 511 Size 45 x 45 cm deep including RCC/C.I. manhole cover medium duty with frame of size 45x45mm size/ Concrete Slab. With F.P.S. bricks with class designation 75 and with crushed stone aggregate complete in all respects. 512 Providing and fixing of PVC pipe (Type "B") in proper gradient in excavated trenches including jointing and refilling the excavated material complete including cost of excavation. (Sample to be approved by EIC) 513 150mm dia. Pipe (Including necessary fittings) 514 100mm dia. Pipe 515 75mm dia. Pipe 516 50mm dia. Pipe (Push Type) 517 Providing and fixing of the following PVC fittings. (Sample to be approved by EIC) 518 Plain bend. 519 100mm 520 75mm 521 Collar 522 100 mm 523 75 mm 524 Door Bend 525 100 mm 526 75 mm 527 Door Tee 528 100 mm 529 75 mm 530 Plain Tee 531 100 mm 532 75 mm 533 Door Junction Four Way 534 100 mm 535 75 mm 536 Plain Junction Four Way 537 100 mm 538 75 mm 539 Floor Trap 540 100 mm 541 75 mm 542 Multi Trap 100mm 543 Providing and fixing of Health Faucet / jet spray with plastic flexible pipe 8 mm dia, 1.5 m long, wall hooked complete as required, including necessary accessories , installation charges and complete in full respect as per the directions of Engineer- in-charge. 544 Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931 545 Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 546 Providing and fixing spindle 15mm dia. All types like washer type/disc type etc. 547 Providing & Replacing of Siphon to flushing cistern(Sample to be approved by EIC) 548 Providing & Replacing of washer to Siphon of flushing cistern 549 Providing & Replacing of handle to Siphon of flushing cistern 550 Providing & Replacing of ball cock of flushing cistern without float 551 Providing & Replacing of ball cock of flushing cistern with float 552 Providing & fixing of pvc panelling minimum 5mm thick of approved make including all related acessories like corner/topflashing, etc complete including grounds, including fixing,screwing complete 553 Providing & fixing wallpaper of approved pattern & quality to wall surface including chemical & adhesive as per directions of EIC 554 Providing & fixing curtain rod S.S 555 Providing & fixing curtain Brackets S.S 556 Providing & fixing curtain Knob S.S 557 Providing & fixing Ornamental Brackets 558 Providing & fixing Ornamental Knobs 559 Touchwood polishing,two or more coats on wood work including pressing of nails,scrapping with emery paper, a coat of wood filler & fevicol washing complete as per directions of EIC on new wood work. 560 Touchwood polishing,two or more coats on wood work including a coat of wood filler & fevicol washing complete as per directions of EIC.also including removing of old existing finishing by proper scrapping with sanding/emery paper as per directions of EIC. 561 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plainPolypropylene random fittings, (including necessary PPR reducers) etc. This includes testing of joints complete as per direction of Engineer incharge.Internal work Concealed fixing the pipe etc. (Sample to be approved by the EIC) 562 Internal work Concealed fixing the pipe ......etc. PN-16 pipe , 25mm OD 563 Internal work Concealed fixing the pipe ......etc. PN-16 pipe , 32mm OD 564 Internal work exposed on wall with clamps ......etc. PN-16 pipe , 25mm OD 565 Internal work exposed on wall with clamps ......etc. PN-16 pipe , 32mm OD 566 Internal work exposed on wall with clamps ......etc. PN-16 pipe , 40mm OD 567 Internal work exposed on wall with clamps ......etc. PN-10 pipe , 50mm OD 568 External work including trenching, refilling etc. PN-16 pipe , 25mm OD 569 External work including trenching, refilling etc. PN-16 pipe , 32mm OD 570 External work including trenching, refilling etc. PN-16 pipe , 40mm OD 571 External work including trenching, refilling etc. PN-10 pipe , 50mm OD 572 External work including trenching, refilling etc. PN-10 pipe , 63mm OD 573 Providing and fixin of PPR Male/ Female Adaptors (All types like elbows, tees etc) (Sample to be approved by EIC) 574 for 25mm dia. 575 for 32mm dia. 576 for 40mm dia. 577 Providing and fixing PPR Unions 578 PPR Union 20mm 579 PPR Union 25mm 580 PPR Union 32mm 581 PPR Union 40mm 582 PPR Union 50mm 583 PPR Union 63mm 584 PPR Union 75mm 585 Providing and fixing PPR ball valves (Sample to be approved by EIC) 586 for 25mm dia. 587 for 32mm dia. 588 for 40mm dia. 589 for 50mm dia. 590 for 63mm dia. 591 Providing and fixing of thermal insulation over following dia G.I Pipes at all heights 592 for 15mm dia. 593 for 20mm dia. 594 for 25mm dia. 595 for 40mm dia. 596 Providing and fixing C.P. two way brass bib cock of approved quality ((Sample to be approved by EIC) 15mm nominal bore 597 Providing and fixing C.P. two way brass 2 way angle valve of approved quality ((Sample to be approved by EIC) 15mm nominal bore 598 Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-incharge. Made of G.I. wire of dia 4 mm 599 Providing & fixing 15mm CP Nipples complete all inclusive 600 Engagement of Hilti for cutting slab, demolishing of concrete etc 601 Repairs of Aluminium Doors/ Windows partition including cost of necessary beading, fasteners, screws, rubber gaskits complete 602 Providing & fixing of stainless steel (grade 304) railing made of hollow tubes,channels etc including welding grinding,buffing ,polishing & making curvatures & fitting the same with necessary stainless nuts & bolts complete i.e fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc of required size of the top of the floor or the side of waist slab with suitable arrangements as per approval of engineer in-charge. 603 Newel Post (S.S) fo required size, design as direced by Engineer incharge 604 Providing and fixing of PVC type 3 piece corner shelf (Sample to be approved by EIC) 605 Scientific cleaning & sterilization of Water Storage tanksThe Job involves 6 stage scientific cleaning and sterilization process consisting of Mechanical Dewatering, Hi-Pressure Cleaning, Sludge Removal, Vacuum Cleaning, Antibacterial Spray and finally killing of suspended & floating bacteria by Ultra violet Radiation as detailed below:-1. Dewatering of Tanks:- The Water from the Storage tanks should be pumped out of tanks through Mechanical Dewatering pumps of suitable capacity.2. Exterior Cleaning:- The Roof top, Manholes and External walls of the Water Storage Tanks should be cleaned thoroughly for any traces of dirt, mud and algae present in the close vicinity.3. High Pressure Interior Cleaning:- The interiors of the water storage tanks should be cleaned with high pressure jet which dislodges the layers of dirt and other suspended foreign bodies which may be sticking on the walls. This process will remove the layer of calcination of dirt if any so as to make the interior free of any germs and bacteria. The interiors including the floor , walls and top ceiling of the over head tanks.4. Sludge Removal:- The Dirty water and sludge collected in the previoius operation should be removed using industrial Sludge pumped and disposed off properly away to a safer place so as not to contaminate the water. The floor of water storage tanks should be again cleaned thoroughly using high pressure jet stream so as to remove all the remaining dirt which may be sticking on the floor even after removal of the sludge slurry.5. Drying of tanks:- The water storage tanks should then be dried using industrial Vacuum Cleaners of suitable capacity.6. Antibacterial Spraying:- The inside walls, ceiling and floor of the water storage tanks should then be given the antibacterial treatment which would ensure all interior walls, ceiling and floor surface of the water storage tanks totally germs free.7. Sterilization using Ultra Violet Radiation:- Finally, UV Radiator should be used to ensure the complete wipe out of any bacterial traces which may still be present even after the completion of above processes by giving Ultra Violet Treatment on all Interior SurfacesOver Head Water Storage Tanks/ PVC Water Storage tanks 606 PVC overhead storage tanks 607 Underground Sumps 608 RCC Overhead Storage tanks 609 Providing of Wiring for Lighting point/Ceiling fan point/Ex.fan point/Call bell Point with 1.5 sq mm FRLS PVC Insulated multi strand copper Wire of Polycab /Finolex /Paramount /Anchor make dully isi markedin surface / recessed medium class PVC conduit ,. ( Excl Cost of Conduit ) but including cost of circuit wiring of same sizefrom DB Box to first switch in sub circuit complete job . (Seperate circuit for normal and invertor points )The job includes providing and fixing of 6 Amps one way switch of SSK /REO / Anchor make to be fitted on backlite hylum sheet of required size (incl cost of hylum sheet) to be fitted on walls with necessary screws including refacing of walls whereever required complete job. 610 Providing of Wiring for 16 Amp Power Sockets outlet points in 3x4.0 sq mm ( P+N+E) FRLS PVC Insulated multi strand copper conductorwires of Polycab /Finolex /Paramount /Anchor make to be laidin surface / recessed medium class PVC conduit. ( Excl Cost of Conduit/Channel ) . The job includes providing and fixing of 16 Amps one way switch and 16 Amps one way socketof SSK /REO / Anchor make to be fitted on backlite hylum sheet of required size (incl cost of hylum sheet) to be fitted on walls with necessary screws including refacing of walls whereever required complete job.The job includes circuit wires from DB Box to first switch in sub circuit ,max two pointsshall be paired in one circuit complete job ( No extra circuit wiring will be paid what so ever the length ) 611 Supply. Installation, testing and commissioning of 250 mm sq Shutter Type Exhaust fans of of CG /USHA / Standard /Helonix make 612 Providing ,Installation ,Testing and Commissioning of 12 WAtt LED Surface mounted lighting fixtures (round / Square)having aluminium body (CRCA) of Philips /Havells /Trulux /Helonix /Jaguar /Wipro make dully isi marked,incl 2-pair connection wires complete job. The job includes replacement warrenty of fixture for a period of two years reckoned from date of sucessful commissioning 613 Providing ,laying in position 20/25mm pvc condiut for surface incl cost of necessary clips complete job. 614 Supply Laying and connecting of 4sq mm PVC insulated multi strand copper wire of reputed make dully ISI laid through conduit/channel Excl.cost of conduit/channel. 615 Supply Laying and connecting of 2.5sq mm PVC insulated multi strand copper wire of reputed make dully ISI laid through conduit/channel Excl.cost of conduit/channel. 616 P/F of 15 Amp Box type Switch socket combine with top ISI make for input and output inverter supply. 617 S/I/T& Commissioning of 1200mm sweep heavy duty ceiling fan of ISI make complete with connection to be got approved before installation and fixed at Sub Division room 618 Supplying and fixing of 63 Ampsrating DP 240/415 volts(10KA ) of Legrend /L&T /ABB /Simens /Schinder make dully isi markedcomplete with connections. 619 Supplying and fixing of 32 -40 Ampsrating DP 240/415 volts 910KA)of Legrend /L&T /ABB /Simens /Schinder make dully isi markedcomplete with connections. 620 Wiring for circuit/Sub main Wiring along with earth wire in FRLS PVC insulated 660/1100 volt grade flesible stanmdard copper conductor wire of standard make (to be got approved before installation) in recessed or surface conduting system excluding cost of conduit of following size. 621 2x2.5 Sq.mm +1x2.5 Sq mm circuit wire 622 2x4 Sq.mm +1x4 Sq mm circuit wire 623 2x6 Sq.mm +1x 6Sq mm earth wire 624 4x6 Sq.mm +1x 6Sq mm for X-ray points 625 Supply, Laying and connectinhg of 16Sq. MM PVC insulated Multi Stand Copper wire of rep;uted make dully ISI make laid through conduit executing cost of conduit. 626 Providing/Installation of 1 HP Submersible dewatering pump including commissioning of the same with necessary fittings/fixtures with automatic sensor complete. 627 Providing/Installation of 2 HP Submersible dewatering pump including commissioning of the same with necessary fittings/fixtures with Automatic sensor complete. 628 Removing / Dismantling / Re-Installing after repairs to 2 HP Submersible dewatering pump, including replacing / rewinding of coils if required and change of water level sensors. 629 Carriage of materials by way of mechanical transport including loading unloading leads lifts from source to site of work. 630 Aggregates above 40mm for an average lead of 20Kms 631 Aggregates above 40mm for an average lead of 15Kms 632 Aggregates below 40mm for an average lead of 20Kms 633 Aggregates below 40mm for an average lead of 15Kms 634 Sand for an average lead of 20Kms 635 Sand for an average lead of 15Kms 636 Bricks for an average lead of 25Kms 637 Stones for an average lead of 20Kms 638 Erecting water proof pandaals /shamyanas of required area with crewel ceiling, crewel/theme curtains including removal of same after function and carriage of all materials complete.(On rental basis)per Day:- 639 Pandaals (Waterproof) with Theme/Crewel Ceiling & Curtains: 640 Pandaals (Waterproof)with Crewel Ceiling, without curtains 641 Supplying of Indian National Flag conforming to to the flag code of india of fabric shiny knitted polyester of the following size 642 Providing and fixing of MS pipe of dia 50mm with arrangment of pulley with rope 6mm of required length complete job 643 Supply and laying ofsaw dust (50 Kg Bag) at site including all carriages complete job 644 Supply, laying and spreading of sand mannually including all leads lifts carriages complete job. 645 Hire charges of Genset 2800 wtt for full duration of the event including fuel/Carriages charges all inclusive. Complete job. 646 Hire charges for Fan including Wiring/Electricity/ Fan Charges for full duration of the event. 647 Hire charges for Water coolers including Wiring/Electricity for full duration of the event. 648 Providing and Fixing Unsupported Coloured Flex Display Sheet with subject matter including carriage to venue as directed by EIC 649 Providing and Fixing Coloured Flex Display Sheet with subject matter as directed supported with M.S. Frame including carriage to venue as directed by EIC 650 Providing and Laying Under layment Foam for Matting including carriage to venue as directed by EIC 651 Carriager of Popular wooden joist/planks, from Diviaionl Store to venue and removal of same and then back to Divisional Store as directed by EIC 652 Engagement of labourers and mechanical transport for carriage of material including carriage to venue as directed by EIC 653 Tata Mobile 654 Labourers 655 Hire and laying charges for runners of required size colour and shade including all leads lifts carriages complete job 656 Hire charges for sofas (Three seater) with slip covers etc as directed by EIC including all carriage complete, 657 Hire charges for sofas (Two seater) with slip covers etc as directed by EIC including all carriage complete. 658 Hire and fixing charges buntings of artificial flowers ballons etc to VIP Entrance gate/Row complete job 659 Hire charges of Gas Bukhari with filled gas cylinder including carriages to and fro complete. 660 Providing Mineral Water Bottles (500ml) (Kinley/Bisleri) to theparticipants and dignitaries including carriage to venue and disposal of used bottles. 661 Providing of Hand sanitizersof Standard Quality(200 ML) 662 Uprooting rank vegetation and weeding by digging the area to a depth of 60cm removing all weeds and other growth with root incl. disposal of all rubbish with leads and lifts 663 Supplying and stacking of good earth at site including royalty ( earth measured in stacks will be reduced by 20% for payment including all carriages loading and un- loadine 664 Turfing with no. I grass including watering, good earth and fine sand over turf including all carriages, loading and un-loading 665 Supply of various bath room items 666 Cleaning of water stroage tanks with detergent requiste cloronation 667 Cleaning of glass panes, glass top etc 668 P/f of vertical/horizantal blinds with all fixtures as approved by Engineer-In- charge 669 Supply of house keeping items of standrad quality as approved by Engineer Incharge 670 Vipor Long hander 671 Bathroom cleaner 672 WC brush 673 Towels of required size 674 Tissue box 675 Tissue papers 676 Room freshner 677 Bath set of required size 678 Dust bin with cover 679 Phenyl (500 ml) 680 Crewel Curtain Of Required Colour and Design (Hand Work) 2.5 feet x 7.5 feet 681 Simple Curtain 2.5 feet x 7.5 feet 682 Supply and fixing of 8mm thick bevelled edge glass for table tops cut to size to match the design of table including all carriage 683 Painting road surface marking with adequate no. of coats to give uniform finish with read mixed road marking paint conforming to IS: 164, on bituminous surface in white/yellow shade including cleaning the surface of all dirt, scales, oil, grease and 684 Repairs to Hot water Geysers by Providing and fixing with (Complete Job all inclusive) 685 Geyser elements (as per Geyser type) 686 Geyser thermostat 687 Safety valve for geysers. 688 Auto thermo cut for geyser. 689 Bajaj brass/wet type element for water geyser as per Geyser Type 690 Providing and Fixing of Flex Board (PVC) of required height and design including frame work all carriages and costs complete job 691 View/Cutter/Tajeera (Rental basis) 692 Carpet For Dias/ Cultural Programmes and Vip Area Size 10x10(Rental basis) 693 PVC Chairs (Rental Basis) 694 .Excel Matting Runner(Rental basis) 695 Wooden Podium Desk (Rental Basis) 696 V.I.P Chairs (Rental Basis) 697 Refreshment Tea/water bottles/Sweets/Snacks 698 V.I.P Table (Rental Basis) 699 Wet service of Air Conditioners (of any model) a thorough cleaning & washing of all units. 700 Refilling of gas in Air Conditioners of any model. 701 Providing and fixing laminated wooden flooring with foam including necessary beeding/cornices of approved quality required shade as per directions of in charge engineer inclusive of all carriages complete job. 702 Dismantling wooden boarding’s in lining of walls and partitions, excluding supporting members but including stacking within 50 meters lead :Thickness above 25 mm upto 40 mm. 703 Providing and fixing of ornamental balusters of deodar wood of required shape and size including nails screws and top railing Etc. Complete job. As directed by Engineer Incharge 704 Providing and fixing Acrylic Based wallpaper of standard quality as per approved design and colour including fixing with chemical required in all shapes and designs as per the directions of Engineer Incharge Complete Job. 705 Providing and fixing of decorative lamination onboth sides partitions for low height cabins including wooden frame work and 12mm ply and 125mm imported kail wood skirting at the top and bottom complete finished /two coat of polishing and fixing of 8 mm toughen glass of required height at the top includingall carriage and costs complete job. 706 Providing and fixing of computer table/work stations made in 19 mm thick commercial board with laminated (all surfaces) shutters, of approved brand and shade, pattern and make in frames partitions shelves drawers etc. cost of all hardware accessories/fixture etc. complete job. 707 Providing and Fixing Of Chair Covers of Required Material, Design, Shape and Colour as directed by engineer incharge. Including Fixing Charges all Carriage and costs Complete Job. 708 Note. Any other item not covered in the BOQ, if required to be executed at site, shall be paid strictly as per the rate mentioned in JKSOR-2022/LMR after deducting the contractors depreciation

Contact Information