Tender For Procurement And Installation Of Modular Furniture For Administration Block At Iust Campus I Awant ... in India

Work Detail

Procurement And Installation Of Modular Furniture For Administration Block At Iust Campus I Awantipora , Providing And Placing Modular Workstation Of Size 1200W X 600D With Following Specifications Partition Thickness As 52.4 Mmthk And Ht -1200 Including Powder Coated Aluminium Trims. Fin:Out Of 22.5 Mm Thk Panel Formed Out Of Blocks Which Should Be 18 Mm Thk Plb Boards Wrapped With Laminateat Intermediate Level. Top Block Finish Should Be In Fabric Finish.Bottom Block Finish Should Be In Metal Finish. Tiles Be On Main Spine:Top Tiles To Be Fabric Tackable Tile. Bottom Tiles - Plain Metal. Intermediate Blocks On Main Spine Intermediate Blocks To Be Given In Dl +Dl Finish. Wire Management Should Be Through Main Spine- Wires Shouldbe Taken Into The System Through Cable Ducts From The Junction Boxes And Be Carried Upto The Panels Through Concealed Conduits Inside The Blocks. Legs - Metal Powder Coated Legs To Be At The End And Shared Condition. System Shall Also Have 120 Mm High Powder Coated Standalone Panel Legs To Give The System An Elevated Look. Worksurface - Out Of 25 Mm Thk Prelam Particle Board With Flat Pvc Lipping Edge Banding Of Size 1200 Mm W X 600 Mm D.Pedestals- Pedestal Flat Metal Front, Full Ht Free Standing Central Locking Of Size 390 Mm W X 435 Mm D X 646 Mm Ht 3Dr Of 2Box+1File. Cpu Trolley - With Castors. Kbpt With Mousetray - Metal.Note: All Partitions And Side Panels To Have Levelling Screws For Adjustment In Case Of Uneven Floor To Take Care Of +/- 40 Mm Of Uneven Flooring. , Providing, Supplying And Placing Of Workstation Chairs. Seat Assembly: The Seat Assembly Should Bemade Up Of 1.2 ±0.1Cm. Thick Hot-Pressed Plywood , Upholstered With Fabric Upholstery Covers And Moulded Polyurethane Foam. Seat Size: 47.0 Cm. (W) X 48.0 Cm. (D). Back Assembly: The Back Asembly. Should Bemade Of Powder Coated (Oft 40-60 Microns) Tubular Frame Of 0 2.54 ±0.03Cm. X 0.2 ±0.016Cm.Thk. Ms Erw Tube Designed With Contoured Lumbar Support For Extra Comfort. The Back Shouldbeupholsteredusing Doublelayer Spacer Mesh Fabricwith High Tenacity Yarn. Back Size : 46.5 Cm (W) X 60.5 Cm (H). High Resilience (Hr) Polyurethane Foam: The Hrpolyurethanefoamshouldbe Mouldedwithdensity=45+/-2Kg/M3andhardnessload16±2Kgf For25% Compression. Armrests: The One-Piece Armrestsshouldbeinjection Moulded From Black Co-Polymer Polypropylene.Centre-Tilt Mechanism: The Mechanism Should Be Designed With The Following Features: 360°Revolvingtype.17°±2°Maximumtiltonpivotatcentre Uprightpositionlocking.Tilttensionadjustment. Pneumatic Height Adjustment: The Pneumatic Height Adjustment Should Have An Adjustment Stroke Of 11.0 ±0.3Cm. Telescopicbellowassy:Thebellowshouldbe 3Piecetelescopictypeandinjectionmouldedinblack Polypropylene.Pedestalassembly:Thepedestalshouldbe Injectionmouldedinblack33%Glass-Filled Nylon66 And Fitted With 5 Nos. Twin Wheel Castors. The Pedestal Should Be66.3 ±0.5Cm. Pitch-Center Dia. (76.3 ±1.0Cm With Castors.) Twin Wheel Castors: The Twin Wheel Castors Should Beinjection Moulded In Black Nylon. Seat Height - Min 43.3 To Max 54.3Cm. Height - Min 89.5 To Max 100.5Cm. Width & Depth Of Chair As Measured From Pedestal - Width-76.3 Cm And Depth-76.3 Cm. , Providing And Placing Modular Workstation Of Size 1800X1800x 600 With Following Specifications Partition Thickness As 52.4 Mmthk And Ht -1200 Including Powder Coated Aluminium Trims. Fin:Out Of 22.5 Mm Thk Panel Formed Out Of Blocks Which Should Be 18 Mm Thk Plb Boards Wrapped With Laminateat Intermediate Level. Top Block Finish Be In Fabric Finish.Bottom Block Finish To Be In Metal Finish. Tiles Be On Main Spine:Top Tiles To Be Fabric Tackable Tile. Bottom Tiles - Plain Metal. Tiles On Return Panel:Top Tiles To Be Fabric Tackable Tile. Bottom Tiles - Plain Metal. Intermediate Blocks On Main Spine Intermediate Blocks To Begiven In Dl +Dl Finish. Wire Management Through Main Spine- Wires Should Be Taken Into The System Through Cable Ducts From The Junction Boxes And Be Carried Upto The Panels Through Concealed Conduits Inside The Blocks. Legs - Metal Powder Coated Legs At The End And Shared Condition. System Shall Also Have 120 Mm High Powder Coated Standalone Panel Legs To Give The System An Elevated Look. Worksurface - Out Of 25 Mm Thk Prelam Particle Board With Flat Pvc Lipping Edge Banding Of Size 1800 Mm X 1800 Mm X 600 Mm D. Pedestals-Pedestal Flat Metal Front, Full Ht Free Standing Central Locking Of Size 390 Mm W X 435 Mm D X 646 Mm Ht 3Dr Of 2Box+1File. Cpu Trolley - With Castors. Kbpt With Mousetray - Metal.Note: All Partitions And Side Panels Have Levelling Screws For Adjustment In Case Of Uneven Floor To Take Care Of +/- 40 Mm Of Uneven Flooring. , Providing, Supplying And Placing Of Workstation Chairs. Seat Assembly: The Seat Assembly Should Bemade Up Of 1.2 ±0.1Cm. Thick Hot-Pressed Plywood , Upholstered With Fabric Upholstery Covers And Moulded Polyurethane Foam. Seat Size: 47.0 Cm. (W) X 48.0 Cm. (D). Back Assembly: The Back Asembly Should Bemade Of Powder Coated (Oft 40-60 Microns) Tubular Frame Of 0 2.54 ±0.03Cm. X 0.2 ±0.016Cm.Thk. Ms Erw Tube Designed With Contoured Lumbar Support For Extra Comfort. The Back Shouldbeupholsteredusing Doublelayer Spacer Mesh Fabricwith High Tenacity Yarn. Back Size : 46.5 Cm (W) X 70.5 Cm (H). High Resilience (Hr) Polyurethane Foam: The Hrpolyurethanefoamshouldbe Mouldedwithdensity=45+/-2Kg/M3andhardnessload16±2Kgf For25% Compression. Armrests: The One-Piece Armrests Should Beinjection Moulded From Black Co-Polymer Polypropylene.Centre-Tilt Mechanism: The Mechanism Should Be Designed With The Following Features: 360°Revolvingtype.17°±2°Maximumtiltonpivotatcentre Uprightpositionlocking.Tilttensionadjustment. Pneumatic Height Adjustment: The Pneumatic Height Adjustment Has An Adjustment Stroke Of 11.0 ±0.3Cm. Telescopicbellowassy:Thebellowshouldbe 3Piecetelescopictypeandinjectionmouldedinblack Polypropylene.Pedestalassembly:Thepedestalshouldbe Injectionmouldedinblack33%Glass-Filled Nylon66 And Fitted With 5 Nos. Twin Wheel Castors. The Pedestal Should Be66.3 ±0.5Cm. Pitch-Center Dia. (76.3 ±1.0Cm With Castors.) Twin Wheel Castors: The Twin Wheel Castors Should Beinjection Moulded In Black Nylon. Overall Dimensions Of Chair Seat Height - Min 43.3 To Max 54.3Cm. Height - Min 99.5 To Max 110.5Cm.Width & Depth Of Chair As Measured From Pedestal - Width-76.3 Cm And Depth-76.3 Cm. , Providing And Placing Modular Workstation Of Size 1650X1650x600 With Following Specifications Partition Thickness As 52.4 Mmthk And Ht -1200 Including Powder Coated Aluminium Trims. Fin:Out Of 22.5 Mm Thk Panel Formed Out Of Blocks Which Should Be 18 Mm Thk Plb Boards Wrapped With Laminateat Intermediate Level. Top Block Finish Be In Fabric Finish.Bottom Blockfinish Be In Metal Finish. Tiles On Main Spine:Top Tiles Are Fabric Tackable Tile. Bottom Tiles - Plain Metal. Tiles On Return Panel:Top Tiles To Be Fabric Tackable Tile. Bottom Tiles - Plain Metal. Intermediate Blocks On Main Spine Intermediate Blocks Be Given In Dl +Dl Finish. Wire Management Through Main Spine- Wires Should Be Taken Into The System Through Cable Ducts From The Junction Boxes And Be Carried Upto The Panels Through Concealed Conduits Inside The Blocks. Legs - Metal Powder Coated Legs At The End And Shared Condition. System Shall Also Have 120 Mm High Powder Coated Standalone Panel Legs To Give The System An Elevated Look. Worksurface - Out Of 25 Mm Thk Prelam Particle Board With Flat Pvc Lipping Edge Banding Of Size 1650Mmw1x1650mmw2x600mmd. Pedestals-Pedestal Flat Metal Front, Full Ht Free Standing Central Locking Of Size 390 Mm W X 435 Mm D X 646 Mm Ht 3Dr Of 2Box+1File. Cpu Trolley - With Castors. Kbpt With Mousetray - Metal.Note: All Partitions And Side Panels Have Levelling Screws For Adjustment In Case Of Uneven Floor To Take Care Of +/- 40 Mm Of Uneven Flooring. , Providing And Fixing Full Back Rest Workstations Revolving Chairs With The Following Specifications.The Back Be Made Up Of 1.2 ±0.1Cm. Thick Hot-Pressed Plywood & Seat Be Made Up Of 1.5 ±0.1Cm. Thick Hot-Pressed Plywood Measured As Per Qa Method Described In Ocp-Qlta-P14-18And Upholstered With Leatherite Upholstery Covers And Moulded Polyurethane Foam. The Back Foam Be Designed With Contoured Foam Lumbar Support. The Seat Should Have Extra Thick Foam On Front Edge To Give Comforttopoplitealarea.Therecronfilling To Be Done Inseat&Back(Executivechairsonly)Forextrafluffinessand Comfort In Chair. (Full Back) Size: 76.1Cm (W) X 76.1Cm. (D). 101.5-111.5Cm (H) X 46.0-56.0Cm Sh. The Hr Polyurethanefoambemouldedwithdensity =45±2Kg/M3andhardnessload14±2Kgfasperis:7888For25% Compression.Theadjustablearmrestbedesignedwiththefollowingfeaturesup-Downadjustment–6Steps(7.2± 0.5Cm Range) Armrest Top Be Mounted On Armrest Structure Made Of Glass Filled Nylon. Armrest Top Be Pu Moulded Over Glass Filled Nylon Insert. The Mechanism Be Designed With The Following Features: 360° Revolving Type. 3 Position Locking With Anti Shock Mechanism. Tilt Tension Adjustment.The Pedestal Be Injection Moulded In Black Glass-Filled Nylon And Fitted With 5 Nos. Twin Wheel Castors. , Providing And Placing Modular Workstation Of Size 1500X1500x600 With Following Specifications Partition Thickness As 52.4 Mmthk And Ht -1200 Including Powder Coated Aluminium Trims. Fin:Out Of 22.5 Mm Thk Panel Formed Out Of Blocks Which Should Be 18 Mm Thk Plb Boards Wrapped With Laminateat Intermediate Level. Top Block Finish Be In Fabric Finish.Bottom Block Finish Be In Metal Finish. Tiles On Main Spine:Top Tiles Be Fabric Tackable Tile. Bottom Tiles - Plain Metal. Tiles On Return Panel:Top Tiles Be Fabric Tackable Tile. Bottom Tiles - Plain Metal. Intermediate Blocks On Main Spine Intermediate Blocks Be Given In Dl +Dl Finish. Wire Management Through Main Spine- Wires Should Be Taken Into The System Through Cable Ducts From The Junction Boxes And Be Carried Upto The Panels Through Concealed Conduits Inside The Blocks. Legs - Metal Powder Coated Legs At The End And Shared Condition. System Shall Also Have 120 Mm High Powder Coated Standalone Panel Legs To Give The System An Elevated Look. Worksurface - Out Of 25 Mm Thk Prelam Particle Board With Flat Pvc Lipping Edge Banding Of Size 1500Mmw1x1500mmw2x600mmd. Pedestals-Pedestal Flat Metal Front, Full Ht Free Standing Central Locking Of Size 390 Mm W X 435 Mm D X 646 Mm Ht 3Dr Of 2Box+1File. Cpu Trolley - With Castors. Kbpt With Mousetray - Metal.Note: All Partitions And Side Panels Have Levelling Screws For Adjustment In Case Of Uneven Floor To Take Care Of +/- 40 Mm Of Uneven Flooring. , Providing And Placing Modular Workstation Of Size 1500X1200x600 With Following Specifications Partition Thickness As 52.4 Mmthk And Ht -1200 Including Powder Coated Aluminium Trims. Fin:Out Of 22.5 Mm Thk Panel Formed Out Of Blocks Which Should Be 18 Mm Thk Plb Boards Wrapped With Laminateat Intermediate Level. Top Block Finish Be In Fabric Finish.Bottom Block Finish Be In Metal Finish. Tiles On Main Spine:Top Tiles Be Fabric Tackable Tile. Bottom Tiles - Plain Metal. Tiles On Return Panel:Top Tiles Be Fabric Tackable Tile. Bottom Tiles - Plain Metal. Intermediate Blocks On Main Spine Intermediate Blocks Be Given In Dl +Dl Finish. Wire Management Through Main Spine- Wires Should Be Taken Into The System Through Cable Ducts From The Junction Boxes And Be Carried Upto The Panels Through Concealed Conduits Inside The Blocks. Legs - Metal Powder Coated Legs At The End And Shared Condition. System Shall Also Have 120 Mm High Powder Coated Standalone Panel Legs To Give The System An Elevated Look. Worksurface - Out Of 25 Mm Thk Prelam Particle Board With Flat Pvc Lipping Edge Banding Of Size 1500Mmw1x1500mmw2x600mmd. Pedestals-Pedestal Flat Metal Front, Full Ht Free Standing Central Locking Of Size 390 Mm W X 435 Mm D X 646 Mm Ht 3Dr Of 2Box+1File. Cpu Trolley - With Castors. Kbpt With Mousetray - Metal.Note: All Partitions And Side Panels Have Levelling Screws For Adjustment In Case Of Uneven Floor To Take Care Of +/- 40 Mm Of Uneven Flooring. , Providing And Placing Modular Workstation Of Size 2250Wx2700d With Following Specifications Partition Thickness As 52.4Mm Thk And Ht-1200 Including Powder Coated Aluminium Trims.Fin:Out Of 22.5 Mm Thk Panel Formed Out Of Blocks Which Should Be 18 Mm Thk Plb Boards Wrapped With Laminateat Intermediate Level. Top Block Finish Be In Fabric Finish.Bottom Block Finish Be In Metal Finish. Tiles On Main Spine:Top Tiles Be Fabric Tackable Tile. Bottom Tiles - Plain Metal. Tiles On Return Panel:Top Tiles Be Fabric Tackable Tile. Bottom Tiles - Plain Metal. Intermediate Blocks On Main Spine Intermediate Blocks Be Given In Dl +Dl Finish. Wire Management Through Main Spine- Wires Should Be Taken Into The System Through Cable Ducts From The Junction Boxes And Be Carried Upto The Panels Through Concealed Conduits Inside The Blocks. Legs - Metal Powder Coated Legs At The End And Shared Condition. System Shall Also Have 120 Mm High Powder Coated Standalone Panel Legs To Give The System An Elevated Look. Worksurface - Out Of 25 Mm Thk Prelam Particle Board With Flat Pvc Lipping Edge Banding Of Size 1500Mmw1x1500mmw2x600mmd. Pedestals-Pedestal Flat Metal Front, Full Ht Free Standing Central Locking Of Size 390 Mm W X 435 Mm D X 646 Mm Ht 3Dr Of 2Box+1File. Cpu Trolley - With Castors. Kbpt With Mousetray - Metal.Note: All Partitions And Side Panels Have Levelling Screws For Adjustment In Case Of Uneven Floor To Take Care Of +/- 40 Mm Of Uneven Flooring.. Providing And Placing Modular Workstation Of Size 1500Wx2700d/ Free Standing Panel 2700W With Following Specifications Partition Thicknessas 52.4Mm Thk And Ht-1200 Including Powder Coated Aluminium Trims.Fin:Out Of 22.5Mm Thk Panel Formed Out Of Blocks Which Are 18Mm Thk Plb Boards Wrapped With Laminate At Intermediate Level.Top Block Finished In Fabric Finish. Bottom Block Finish Be In Metal Finish.Tiles On Main Spine:Top Tiles Be Fabric Tackable Tile.Bottom Tiles-Plain Metal. Tiles On Return Panel: Top Tiles Are Fabric Tackable Tile.Bottom Tiles-Plain Metal. Intermediate Blocks On Main Spine Intermediate Blocks Be Given In Dl+Dlfinish. Wire Management Through Main Spine-Wires Should Be Taken Into The System Through Cable Ducts From The Junction Boxes And Be Carried Upto The Panels Through Concealed Conduits Inside The Blocks. Legs-Metal Powder Coated Legs At The End And Shared Condition. System Shall Also Have 120Mm High Powder Coated Standalone Panel Legs To Give The System An Elevated Look.Worksurface-Out Of 25Mm Thk Prelam Particle Board With Flat Pvc Lipping Edge Banding Of Size 1500Mmwx600mmd And Eru Table Recta Of Size 900Mmwx450mmd. Pedestals-Pedestal Flat Metal Front,Full Ht Free Standing Central Locking Of Size 390Mmwx435mmdx646mm Ht 3 Dr Of 2Box+1File. Cpu Trolley-With Castors. Kbpt With Mousetray-Metal.Note:All Partitions And Side Panels Have Levelling Screws For Adjustment In Case Of Uneven Floor To Take Care Of +/- 40 Mm Of Uneven Flooring. , Providing And Fixing High Back Executive Workstation Chair With Arm Rest Of The Following Specifications.The Back Be Made Up Of 1.2 ±0.1Cm. Thick Hot-Pressed Plywood & Seat Be Made Up Of 1.5 ±0.1Cm. Thick Hot-Pressed Plywood Measured As Per Qa Method Described In Ocp-Qlta-P14-18And Upholstered With Leatherite Upholstery Covers And Moulded Polyurethane Foam. The Back Foam Be Designed With Contoured Foam Lumbar Support. The Seat Should Have Extra Thick Foam On Front Edge To Give Comforttopoplitealarea.Therecronfillingdoneinseat&Back(Executivechairsonly)Forextrafluffinessand Comfort In Chair. (High Back) Size: 76.1Cm (W) X 76.1Cm. (D).113.5-123.5Cm (H) X 46.0-56.0Cm Sh. The Hr Polyurethanefoambemouldedwithdensity =45±2Kg/M3andhardnessload14±2Kgfasperis:7888For25% Compression.Theadjustablearmrestbedesignedwiththefollowingfeaturesup-Downadjustment–6Steps(7.2± 0.5Cm Range) Armrest Top Be Mounted On Armrest Structure Be Made Of Glass Filled Nylon. Armrest Top Be Moulded Over Glass Filled Nylon Insert. The Mechanism Be Designed With The Following Features: 360° Revolving Type. 3 Position Locking With Anti Shock Mechanism. Tilt Tension Adjustment. The Pedestal Be Made Of Injection Moulded In Black Glass Filled Nylon And Filled With 5 Nos. Twin Wheel Castors. , Providing And Fixing Mesh Back Visitor Chair With The Following Specificaitons The Seat Assembly Shall Be Made Up Of 1.2 ±0.1Cm. Thick Hot-Pressed Plywood Shall Be Upholstered With Fabric Upholstery Covers And Moulded Polyurethane Foam. The Dimensions Of Seat Shall Be 47.0 Cm. (W) X 48.0 Cm. (D). The Back Asembly Shall Be Made Of Powder Coated (Dft 40-60 Microns) Tubular Frame Of Dia 2.54 ±0.03Cm.X 0.2±0.016Cm Thk.Ms Erw Tube Designed With Contoured Lumbar Support For Extra Comfort. The Back Shall Be Upholstered Using Net Fabric With High Tenacity Yarn. The Dimensions Of Back Shall Be 46.5 Cm (W) X 60.5 Cm (H). The Hr Polyurethanefoam Shall Be Moulded With Density =45+/-2 Kg/M3 And Hardness Load 16 ± 2 Kgf As Per Is:7888 For 25% Compression. The One-Piece Armrests Shall Be Injection Moulded From Black Co-Polymer Polypropylene. The Powder Coated (Dft 40-60 Microns) Tubular Frame Shall Be Cantilever Type & Made Ofdia 2.54±0.03Cmx0.2 ±0.016Cm.Thk. M.S. Er.W. Tube. Overall Dimensions Of Chair Shall Be Seat Height - 46.5Cm, Height - 93.5Cm, Width & Depth Of Chair As Measured From Pedestal -Width-61.0 Cm And Depth-64.5 Cm. , Supplying And Placing In Position Main Table,Eru & Pedestal Of The Following Specifications. Overall Dimension 1800X2100x750 Primary Work Surface Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Secondary Work Surface Be Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top. Softclosing Access Flap With In-Build Power Box To Be Provided On Work Surface For Wire Management. Modesty Panel Be Made Of 25Mm Thick Mdf One Side Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Under- Structure Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Integrated Pedestal Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Drawer Fronts Be Made Of 25Mm Thick Mdf With One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Pedestal Construction Be Box-Box-File Type Which Should Have Powder Coated 400 Mm Long Metal Panel Drawer Slides. Drawer Extension Be 325 Mm. Drawers Should Have A Soft Closing & Anti Slam Mechanism. Handles Be Provided For Ease Of Opening. Pedestal And Provided With Lock For Security. , Providing And Fixing High Back Executive Chair With Arm Rest Of The Following Specifications.The Back Be Made Up Of 1.2 ±0.1Cm. Thick Hot-Pressed Plywood & Seat Be Made Up Of 1.5 ±0.1Cm. Thick Hot-Pressed Plywood Measured As Per Qa Method Described In Ocp-Qlta-P14-18And Upholstered With Leatherite Upholstery Covers And Moulded Polyurethane Foam. The Back Foam Be Designed With Contoured Foam Lumbar Support. The Seat Should Have Extra Thick Foam On Front Edge To Give Comforttopoplitealarea.Therecronfillingto Be Doneinseat&Back(Executivechairsonly)Forextrafluffinessand Comfort In Chair. (High Back) Size: 76.1Cm (W) X 76.1Cm. (D).113.5-123.5Cm (H) X 46.0-56.0Cm Sh. The Hr Polyurethanefoambemouldedwithdensity =45±2Kg/M3andhardnessload14±2Kgfasperis:7888For25% Compression.Theadjustablearmrestbedesignedwiththefollowingfeaturesup-Downadjustment–6Steps(7.2± 0.5Cm Range) Armrest Top Be Mounted On Armrest Structure And Made Of Glass Filled Nylon. Armrest Top Be Pu Moulded Over Glass Filled Nylon Insert. The Mechanism Be Designed With The Following Features: 360° Revolving Type. 3 Position Locking With Anti Shock Mechanism. Tilt Tension Adjustment. . The Pedestal Is Made Of Injection Moulded In Black Glass Filled Nylon And Filled With 5 Nos. Twin Wheel Castors , Supplying And Placing In Position Credenza Of The Following Specifications. Overall Dimension 1800X500x750 Top Panel Be Made Of 25Mm Thick Mdf With One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Slide Door Unit Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shad Confirming Tois-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping For Body Panels Like Side, Bottom,Back And Shelves. Shutters To Bemade Of 25Mm Thick Mdf With One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top. Shutters Should Have A Soft Closing & Anti Slam Mechanism. Handles To Be Provided For Ease Of Opening. Storage Be Provided With Lock For Security. , Supplying And Placing In Position Main Table,Eru & Pedestal Of The Following Specifications. Overall Dimension 1650X1950x750 Primary Work Surface Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Secondary Work Surface Be Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top. Softclosing Access Flap With In-Build Power Box To Be Provided On Work Surface For Wire Management. Modesty Panel Be Made Of 25Mm Thick Mdf One Side Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Under- Structure Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Integrated Pedestal Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Drawer Fronts Be Made Of 25Mm Thick Mdf With One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Pedestal Construction Be Box-Box-File Type Which Should Have Powder Coated 400 Mm Long Metal Panel Drawer Slides. Drawer Extension Be 325 Mm. Drawers Should Have A Soft Closing & Anti Slam Mechanism. Handles Be Provided For Ease Of Opening. Pedestal And Provided With Lock For Security. , Providing And Fixing High Back Executive Chair With Arm Rest Of The Following Specifications.The Back Be Made Up Of 1.2 ±0.1Cm. Thick Hot-Pressed Plywood & Seat Be Made Up Of 1.5 ±0.1Cm. Thick Hot-Pressed Plywood Measured As Per Qa Method Described In Ocp-Qlta-P14-18And Upholstered With Leatherite Upholstery Covers And Moulded Polyurethane Foam. The Back Foam Be Designed With Contoured Foam Lumbar Support. The Seat Should Have Extra Thick Foam On Front Edge To Give Comforttopoplitealarea.Therecronfillingto Be Doneinseat&Back(Executivechairsonly)Forextrafluffinessand Comfort In Chair. (High Back) Size: 76.1Cm (W) X 76.1Cm. (D).113.5-123.5Cm (H) X 46.0-56.0Cm Sh. The Hr Polyurethanefoambemouldedwithdensity =45±2Kg/M3andhardnessload14±2Kgfasperis:7888For25% Compression.Theadjustablearmrestbedesignedwiththefollowingfeaturesup-Downadjustment–6Steps(7.2± 0.5Cm Range) Armrest Top Be Mounted On Armrest Structure And Made Of Glass Filled Nylon. Armrest Top Be Pu Moulded Over Glass Filled Nylon Insert. The Mechanism Be Designed With The Following Features: 360° Revolving Type. 3 Position Locking With Anti Shock Mechanism. Tilt Tension Adjustment. . The Pedestal Is Made Of Injection Moulded In Black Glass Filled Nylon And Filled With 5 Nos. Twin Wheel Castors , Wooden Storage Range Comprises Of A Range Of Low Height To Medium Height Wooden Hdu And Sdu Of Size 900Wx450dx740h . Body Be Made From 18Mm Plb With All The Edges Sealed With 0.8 Mm Thick Pvc Edgeband. The Back Panel Be 9Mm White Plt. The Entire Construction Be Ready To Assemble Unit And Be Assembled With Suitable Kd Fittings. The Shelves And Separator Panels Be Made From 18 Mm White Plt And Edges To Be Sealed With 0.8 Mm Edge Band. The Bottom Shelf Be Fixed And Other Shelves Should Have One Step Adjustment For Optimizing The Space. Doors : Door Panels Be Made From 18 Mm Plb With 2 Mm Edge Band On All Edges Ad A Flush Plastic Handle Be Fitted Vertically At The Center Of The Door. The Hinge Door Should Have Suitable Hinges And Hdu Be Fitted With An Adjustable Fitting For Height Adjustment. The Sdu Shoudl Run In A Pvc Track Mounted On The Top And Bottom Panel Of The Body. Hdu Should Have Three Point Lock And Sdu Should Have Push Type Lock. All The Storages Are Fitted With A 6 Mm Leveler At Bottom For Leveling. , Supplying And Placing In Position Reception Table Of The Following Specifications. Work Surface Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Access Flap Along With A Gromett Be Provided On Work Surface For Wire Management Wire Management - Power Box Be Made With 0.8 Mm Thick Crca (Is: 513), With Switch Plate (8+3 Module Cut Out Provision For Anchor Roma) Which Should Be Fixed With Worktop Along The Width At Access Flap Position. Modesty Panel & Side Skirting Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Understructure Be Made Of 18Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping Top Shelf Be Made Of 18Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Hinge Door + Drawer Unit Be Made Of 18Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. **Drawer Bottom Be Made Of 5.5Thk Mdf Whiteboard Handle Be Provided For Ease Of Opening. Hdu And Drawer Be Provided With Cam Lock For Security. Essential Accessories - Wire Riser Be Made Of 0.8Mm Crca (Is-513)Provided For Proper Wire Management. Organizer Plate Be Made Of 1.2Mm Crca (Is-513)Provided For Magnetic Sticky Notes. Bag Hanger Hook Be Made Of 1.2Mm Crca (Is-513) Provided For Bag Hanging. Table Size - Length - 2400Mm Depth - 1770,870Mm Height - 1080Mm , Overall Dimensions Of Td - 2 Twin Drive Unit 2 Bay(U/C + Fittings + Cover) Shall Be 2400Mm(W)X800mm(D)X1980mm(H). The Construction Shall Be Rigid Knock Down Made Out Of 0.8 Thick Crca Steel Conforming To Is : 513 . Each Body Shall Have A Main Unit Plus An Add On Unit.Finish Shall Be Epoxy Polyester Powder Coated Thickness Of 40 Microns . Shelf Construction Shall Be Made From Crca Steel 0.8 Mm Thick Is :513 .Uniformly Distributed Load Capacity Of 100 Kg . Undercarriage Shall Have Construction In Welded Frame Made Of Hr Sheet 3 Mm Thick Conforming To Is : 2062. The Movements Shall Be Drive Type Configuration Achieved Mechanically Through A Pu Drive Wheel And Sprocket -Chain-Tensioner Arrangement Mounted Rigidly Onto Body Size. For 2-Bay Drive Type Each Movable Undercarriage Shall Be Provided With 2 Rollers On The Shaft For Driving , 2 Antifriction Ball Bearing For Rolling. The Roller Assembly Comprises Of A Die-Cast Step Wheel, 2 Deep-Groove Ball Bearings And A Ms Shaft. The Step Wheel Is Made Of Cast Steel And Is Fitted Onto The Ms Shaft Using A Feather Key. The Two Ball Bearings Are Then Fastened On Either Side Of The Step Wheel Using Circlips. This Entire Roller Assembly Is Then Snap-Fitted Into A Wheel Housing. The Wheel Housing Is Fixed In The Uchannel Of The Understructure Using Machine Screws. This Wheel-Housing Is Made Of Engineering Plastic Material Made By Injection-Molding Process. The Entire Roller Assembly Is Designed To Withstand The Maximum Loads Of The Body. Fittings Shall Be Centralized Locking Arrangement Through Locking Stiffener Mounted Onto Back Of Single Last Unit So That It Gets Locked On Channels When All The Units Are Brought Together .The ‘Sprocket-Chain’ Arrangement Is Covered By A 1 Mm Thk. Crca Sheet Drive Unit Cover With Dimensions 1202Mm X 398Mm X 87Mm And Is Fixed Onto The Side Of The Body. The Pu Handwheel Is Rigidly Fixed At Suitable Height On Side Of The Body & Projects Out Of Cover By Another 99.0 Mm. Fixed Unit (Sd) Does Not Have The Drive Unit Cover. Each Drive Type Units Shall Have Locking Knob Near The Drive Wheel For Manual Locking Of Individual Units. Knob Shall Be Rotated To Unlock Position When Units Are To Be Moved. End Stoppers Shall Be Provided To Prevent Derailment. The Nuts & Bolts Are Galvanized / Blackodized / Zn Plated.Also Total No. Of Loading Levels Per Understructure Shall Be 24. Label Holder - It Is An Aluminium Extrusion Of Length 396Mm For Ld/Sd And 796Mm For Td, Fitted On To Front Cover Of Body. The Paper Is 300Gsm Matt Milky White Sticker Paper, To Be Inserted Into The Aluminium Extrusion. The Length Of Paper Is 394Mm For Ld/Sd And 794Mm For Td. Over That A Transparent Plastic Of Corresponding Length Of 150-200 Micron Polythene Is To Be Inserted.Td Units Are Designed With Tie Rod Assembly Options As Well. It Acts As A Substitute To The Back Panels (Only In Twin Body) If The Customer Chooses To Not Have Back Panels. The Assembly Consists Of 2 Tie Rods, 4 Fixing Brackets And 2 Turnbuckles. The Tie Rods Are Fixed In A Shape Of ‘X’ Between Two Opposite Shelves. The Tie Rods Are Made Of 4Mm Diameter Rods Of Ms While The Fixing Brackets Are Made Of 2Mm Thk. Crca Steel Conforming To Is: 513 Gr.D. , Providing, Supplying And Placing Of Three Seater Sofa. Side Frame Assembly: The Side Frame Assembly Should Befitted To The Two Ends Of The Connecting Beam Assembly To Form The Leg-Cum-Armrest Assembly. It Should Bemade Of 0 3.81 ±0.03Cm. X 0.2 ±0.016Cm. Thick Cmx0.16Cnn And Black Powder Coated (Dft 40-60Microns). The Ends Should Befitted With Abs Moulded End Caps. Tie Member: It Should Beconnected Beam Assy. To Hold The Two Side Frames To Each Other. 2 Nos. Tie Members Should Beused To Connect The Side Frames. The Tie-Member Should Beof 0 3.81 ±0.03Cm. X 0.2 ±0.016Cm. Thick Cm X 0.16Cm And Black Powder Coated ( Dft 40-60 Microns ). The Seat/Back Assemblies Should Bemounted On One Of The Tie-Member Which Should Be 5.0 ±0.1Cm X 5.0 ±0.1 Cm X 0.5 ±0.1Cm. Thk -- 5.5 ±0.1Cm Long Ms. Std. Angles Welded To Mount The Seat And Back. Seatrest Assembly:The Seat Rest Assembly Cons Should Beof A Fabricated Inner-Frame Assembly Insitu-Moulded High Resilience (Hr) Polyurethane Foam Having Density = 45 +1- 2 Kg/M3 With Hardness Load 25 ± 2 Kgffor 25% Compression Of The Foam. The Complete Moulded Seat Rest Assembly Should Becovered With A Replaceable Fabric Upholstery Cover Seat Size: 52.0Cm. (W) X 50.0Cm. (D) X 6.0Cm. (T) Backrest Assembly:The Backrest Assembly Should Beflexing Type And Cons Should Be Of A Fabricated Inner-Frame Assembly Insitu-Moulded With High Resilience (Hr) Polyurethane Foam Having Density = 45 +1- 2 Kg/M3 With Hardness Load 14 ± 2 Kgffor 25% Compression Of The Foam. The Complete Moulded Backrest Assembly Should Becovered With A Replaceable Fabric Upholstery Cover. Back Size: 52.0Cm. (W) X 59.0Cm. (H) X 6.0Cm. (T) Adj. Glides: The Adj. Glide Should Beinjection Moulded In Black Nylon & Fitted To The Front End Of Side Frame Assembly Along With Abs Moulded Adj. Glide Base To Take And Should Beor Unleveled Floor Surface. Seat Height - 43.5 Cm. Height - 78.5Cm. Width & Depth Of Chair As- Width-164.0Cm And Depth-70.0 Cm. , Providing, Supplying And Placing Of 2 Seater Sofa Leatherite Finsish With Following Specifications. Overall Size : Width : 132.5Cm, Depth : 81.5Cm, Height : 83.5Cm Upholstery : Synthetic Leather, • Frame : Material - Solid Wood Frame With Ply Wood Cross Section Moisture Content : 12% • Foam Density : Seat : 28 Kg/ Cubic Meter • Webbing : S Spring • Legs : Rubber Wood , Providing And Fixing Modular Conference Table Of Height 740Mm, Having Two Seater Modulesof Size 1350X600mm, And Head Module 2350X850mm . Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade With Approved Shade Conforming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Understructure : It Should Consist Of 18Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Conforming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Aluminium Alloy 63400 - Wp Profile Be Used For Connecting Panels Together. The Product Should Have A Knock-Down Construction. Plastic Abs Access Flap Be Provided For Easy Access To Wires And Cables. Work Top Be Available In Various Shapes.Modesty Panel Be Made Of 18Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Should Be Of Approved Shade Conforming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Powder Coated Accent Metal Strip Provided Below Work Surface To Enhance Aesthetics. It Should Be Made Of 0.8Mm Crca As Per Is 513,Epoxy Polyester Powder Coated (Dft 40-60 Microns) Wire Management : An Array Of Panels Be Made Of 0.8Mm Crca Ms Is:513, Epoxy Polyester Powder Coated (Dft 40-60 Microns) And Used For Flow Of Wires And Cables. Provision To Mount 6 Module Plate Be Provided Below Worktop. Cutout On Top With Two Piece Injection Moulded Plastic Part Polymer Component Be Fitted To Pull Out Audio,Video Cables Onto Worktop And Connect Devices Charger To Power Socket Below Worktop.. , Providing And Fixing Full Back Executive Chair For Conference Hall With Arm Rest Of The Following Specifications.The Back Be Made Up Of 1.2 ±0.1Cm. Thick Hot-Pressed Plywood & Seat Be Made Up Of 1.5 ±0.1Cm. Thick Hot-Pressed Plywood Measured As Per Qa Method Described In Ocp-Qlta-P14-18And Upholstered With Leatherite Upholstery Covers And Moulded Polyurethane Foam. The Back Foam Be Designed With Contoured Foam Lumbar Support. The Seat Should Have Extra Thick Foam On Front Edge To Give Comforttopoplitealarea.Therecronfilling To Be Doneinseat&Back(Executivechairsonly)Forextrafluffinessand Comfort In Chair. (High Back) Size: 77.0Cm (W) X 77.0Cm. (D). 98.0-108.0Cm (H) X 44.5-54.5Cm Sh. The Hr Polyurethanefoambemouldedwithdensity =45±2Kg/M3andhardnessload14±2Kgfasperis:7888For25% Compression.Theadjustablearmrestbedesignedwiththefollowingfeaturesup-Downadjustment–6Steps(7.2± 0.5Cm Range) Armrest Top Be Mounted On Armrest Structure Made Of Glass Filled Nylon. Armrest Top Be Pu Moulded Over Glass Filled Nylon Insert. The Mechanism Be Designed With The Following Features: 360° Revolving Type. 3 Position Locking With Anti Shock Mechanism. Tilt Tension Adjustment. The Pedestal Be Made Of Die-Cast Aluminium With Buffing Finish With 5 Nos. Twin Wheel Castors , Providing And Fixing Modular Storage Units Of The Following Specifications Product Size - 450(W)/600(W)/900(W)/1200(W) X 450(D) X 1950*(H)/2325(H) (Height Of Leveler Be 50Mm And Adjustment Possible Be 15Mm. Construction & Material - Aesthetically Appealing Completely Knock Down Construction.The Add-On Units To Be Stacked Widthwise To Form Arow Of Storage. Legs Fitted With Screw Type Leveler Be Made From Combination Of Top Panel(0.5Mm Crca), Side Panel(0.5Mm Crca), Bottom Panel(0.5Mm Crca For 450W/600W And 0.8Mm Crca For 900W/1200W), Back Panel(0.5Mm Crca), Top Bottom Stiffener(1.2Mm Crca) And End Cover(0.5Mm Crca). ** -Crca D Grade As Per Is-513 Shelving - Should Have 12 Bend Panel Made Of 0.7Mm Thick Crca (D Grade, Is-513)Each Shelf Should Have Max Load Capacity Of - 80Kg Udl For 1200W Unit 55Kg Udl For 900W Unit 40Kg Udl For 600W Unit30kg Udl For 450W Unit Of Fixed Shelves For 1950(H)Of Fixed Shelves For 2325(H)A4 Size Box File (85Wx340hx285d) Can Be Stored Vertically On All Loading Levels. Epoxy Polyester Powder Coated To The Thicknessof 50 Microns (+/-10 Micron). Door-Product Size - 2 Doors (Lh And Rh) For 900Wfor900w Storage-Each Door Width 448W Construction & Material - Made From 0.6Mm Thick Crca (D Grade, Is-513) Soft Closing Hinge Handle - Asthetically Appealing Handle Made Of Aluminum Digital Lock- 3 Way Locking Provision- Should Be Available For Private And Public Mode. - Code Finding From The Front By Recovery Key.Shelving - Should Be Having 12 Bend Panel Made Of 0.7Mm Thick Crca (D Grade, Is-513). Each Shelf Should Have Max Load Of 55Kg Udl. Of Fixed Shelves For 1950H. A4 Size Box File (85Wx340hx285d Can Be Stored Vertically On All Loading Levels. , Providing And Fixing Executive Tablewith Following Specification Of Main Table,Eru & Pedestal Of The Following Specifications.2350X2350x750 Primary Work Surface Be Made Of 25Mm Thick Mdf With One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Soft Closing Access Flap With In-Build Power Box Be Provided On Work Surface For Wire Management Secondary Work Surface Be Made Of 25Mm Thick Mdf With One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top. Modesty Panel Be Made Of 25Mm Thick Mdf With One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top. Under Structure Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Integrated Pedestal Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Drawer Fronts Be Made Of 25Mm Thick Mdf With One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Pedestal Constructionbox-Box-File Type Having Powder Coated 400 Mm Long Metal Panel Drawer Slides. Drawer Extension Be 325 Mm. Drawers Should Have A Soft Closing & Anti Slam Mechanism. Handles To Be Provided For Ease Of Opening. Pedestals To Be Provided With Lock For Security. , The Cushioned Seat Should Be Made Of Injection Molded Plastic Outer & Inner. Plastic Inner Should Be Upholstered With Leatherette And Moulded High Resilience (Hr) Polyurethane Foam Of Density 45±2 Kg/M3,And Hardness Load 16 ± 2 Kgf As Per Is:7888 For 25% Compression.The Cushioned Back Should Be Made Of Pu Foam With Insitu Molded Ms E.R.W Round Tube Of Size 1.9±0.03Cm X 0.16 ±0.0128Cm. Be Upholstered With Leatherette Seat Size : 47.0 Cm. (W) X 48.0 Cm. (D) High Back Size: 47.7 Cm. (W) X 76.4 Cm Armrests: The Armrest Top Should Be Moulded From Polyurethane(Pu) And Mounted On To A Drop Lift Adjustable Type Tubular Armrest Support Made Of 03.81±0.03 Cm X 0.2±0.01 Cm Thk M.S. E.R.W Tube Having Chrome Plated Finish.The Armrest Height Adjustable Up To 6.5±0.5Cm In 5 Steps. Active Bio-Synchro Mechanism : The Adjustable Tilting Mechanism Should Be Designed With The Following Features: 360 Revolving Type. Should Have Front-Pivot For Tilt With Feet Resting On Ground And Continuous Lumbar Support Ensuring More Comfort. • Tilt Tension Adjustment Can Be Operated In Seating Position. • 5-Position Tilt Limiter Be Given Option Of Variable Tilt Angle To The Chair. • Seat/Back Tilting Ratio Of 1: 2 • The Mechanism Housing Should Be Made Up Of Hpdc Aluminium Black Powder Coated. Seat Depth Adjustment : Seat Depth Adjustment Should Be Integrated In The Seat Through A Sliding Mechanism. Seat Depth Adjustment Range Should Be Of 6.0±0.5 Cm. Adjustable Back Support: Back Frame Should Be Connected To The Up/Dn Mechanism Housed In Plastic T Spine. It Can Be Adjusted In The Range Of 7.42±0.5 Cm For The Comfortable Back Support To Suit Individual Need. Pneumatic Ht. Adjustment: The Pneumatic Ht Adjustment Should Have An Adjustment Stroke Of 10.0±0.3 Cm. Pedestal Assembly: The Pedestal Should Be High Pressure Die Cast Polished Aluminium And Fitted With 5 Nos. Twin Wheel Castors. The Pedestal Should Be 65.0 ± 0.5Cm. Pitch-Center Dia.(75.0 ± 1.0Cm. With Castors.) Twin Wheel Castors:The Twin Wheel Castors Should Beinjection Moulded In Black Pp Having 6.0± 0.1Cm Wheel Diameter. Overall Dimensions Of Chair Seat Height -43.1-53.1Cm Height -112.7-130.2Cm. Width & Depth Of Chair As Measured From Base - Width-76.1 Cm And Depth-76.1 Cm , Providing And Placing High End Vistor Chair With The Following Specifications.Visitors Chair With Overall Size Of 60.9 W M X 64.2 D Cm X 98.2 H Cm X 44.8 Seat Height Cm. The Seat Be Cushioned Seat Made Of Injection Molded Plastic Outer & Inner. Plastic Inner Be Upholstered With Leatherette And Molded High Resilience Polyurethane Foam Of Density 45±2 Kg/M³, & Hardness Load Of 16±2 Kgf As Per Is:7888 For 25% Compression. Seat Size Be 47.0 W Cm X 48.0 D Cm. The Back Be Cushioned Made Of Pu Foam With Insitu Molded M.S. Erw Round Tube Of Size 1.9±0.03Cm X 0.16±0.0128Cm, Upholstered With Leatherette. The Back Size Be 47.7 W Cm X 76.4 D Cm. The Tubular Frame Be Cantilever Type And Made Of Ø2.54±0.03Cm X 0.2±0.016 Cm Thick Ss 202 Tube. The Back Be Connected To Frame Through Chrome Plated High Pressure Die Casted Connector Pipe. , Providing And Fixing Credenza Of Size 2350X500x750 Top Panel-Made Of 25Mm Thick Mdf With One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top.Slide Door Unit-Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping For Body Panels Like Side, Bottom,Back And Shelves. Shutters Be Made Of 25Mm Thick Mdf With One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top. Shutters Should Have A Soft Closing & Anti Slam Mechanism. Handles Be Provided For Ease Of Opening. Storage To Be Provided With Lock For Security. Display/Storage Unit Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping For Body Panels Like Side,Back And Shelves.Doors Be Made Of 25Mm Thick Mdf With One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top.Top Panel Display Unit Be Made Of 25Mm Thick Mdf With One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top. , Supplying And Placing In Position Executive Main Table Of The Following Specifications Having Size 3000 X 1050 X 740 Main Worktop Be Made Of 43Mm Thick (±1) Combination Of Mdf And Particle Board With Top Veneer Facecoated With Clear Lacquer. All Edges Be Edge Banded With Matching 1Mm Thick Veneerlipping. Leather Pad Be Made Of 18Mm Thick (±1) Mdf With Leatherette Wrapped Around Top Surface. This Leather Pad Be Fixed To Main Top Panel. Drawer Unit:Top Panel And Drawer Unit Modesty Panel Be Made Of 43Mm Thick (±1) Combination Of Mdf And Particle Board With Top Veneer Face Coated With Clear Lacquer. All Thickness Edges Be Edge Banded With Matching Lipping. Remaining Construction Be Of 18Mm Pre-Laminated Twin Board (Plt) Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thickpvc Lipping. Bottom Panel Of Drawer Be 9Mm Thick Particle Board With Leatherette On Top Surface. Drawer Unit Be Provided With Soft Closing Channels For Smooth Opening And Closing.Drawer Unit Be Secured With Side Central Lock. Open Storage Unit:Top Panel And Open Storage Unit Modesty Panel Be Made Of 43Mm Thick (±1) Combination Of Mdf And Particle Board With Top Veneer Face Coated With Clear Lacquer. All Thickness Edges Be Edge Banded With Matching Lipping. Remaining Construction Be Of 18Mm Pre-Laminated Twin Board (Plt) Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thickpvc Lipping. Modesty Be Made Of 18Mm Thick Pre-Laminated Twin Board (Plt) Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvclipping. Modesty Be Fitted With Aluminum Trims. Understructure Be Made Of 18Mm Thick Pre-Laminated Twin Board (Plt) Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvclipping. Door Be Fixed With Soft Closing Hinges And Handle Be Provided For Ease Of Opening. Also Lock Is Provided On Side Panel For Security. Access Flap With Power Box: Soft Closing Access Flap With Power Box Contains 3 Universal Sockets, 2 Usb Powerpoints, 1 Hdmi Connection, 1 Inbuilt Misc. Cable Grommet And Cat 3 And Cat 6Connections. Hidden Wireless Mobile Charger: , Providing And Fixing High Back Executive Revolving Chair With Adjustable Armrest Of The Following Specifications. The Cushioned Seat Inner Be Made Of Injection Moulded Glass Filled Poly-Amide. Upholstered Seat Sub-Assembly Should Consist Of Moulded High Resilience (Hr) Polyurethane Foam Of Density 45±2 Kg/M³, And Hardness Load 16 ± 2 Kgf As Per Is:7888 For 25% Compression. The Cushioned Back Be Made Of Pu Foam With Polypropylene Injection Molded Plastic Inner. (High Back) Size: 74.0Cm (W) X 74.0Cm. (D). 112.0-132.5Cm (H) X 44.5-58.0Cm Sh. The Armrest Should Be Having Range Of Adjustments, Height Adjustment In The Aluminum Arm Body, Up Down Adjustment, Arm Top Swivel Adjustment At Any Position, Arm Top To And Fro Adjsutment Any Position And Armrest Top Be Made Up Of High Dencsity Pu Moulded Over Glass Filled Poly-Amide Inner. Mechanism The Adjustable Tilting Mechanism Be Designed Having Following Features 360° Revolving Type, Forward Tilt Of Sesat And Back, Upright Tilt Lock, Tilt Tension Adjustment To Be Operated In Seating Position And 3 Position Tilt Limiter. Seat Depth Adjustment Be Housed Below The Seat And Integrated With The Mechanism With Help Of Polypropene Seat Cover. Seat Depthbe Adjusted In Sitting Position. Seat Depth Adjustment Range Be Of 5.0±0.5 Cm.. The Mechanism Be Designed With The Following Features: 360° Revolving Type. 3 Position Locking With Anti Shock Mechanism. Tilt Tension Adjustment. . The Pedestal Be Made Of Die-Cast Aluminium With Buffing Finish With 5 Nos. Twin Wheel Castors. Back Assembly Be Connected To Buff Polish Die Cast Aluminum Spine With An Up-Down Mechanism Assembly. Back Height Can Be Adjusted In Sitting Position. It Can Be Adjusted In The Range Of 7.5±0.5 Cm. , Providing And Fixing Full Back Executive Visitor Revolving Chair With Adjustable Armrest Of The Following Specifications. The Cushioned Seat Inner Be Made Of Injection Moulded Glass Filled Poly-Amide. Upholstered Seat Sub-Assembly Consists Of Moulded High Resilience (Hr) Polyurethane Foam Of Density 45±2 Kg/M³, And Hardness Load 16 ± 2 Kgf As Per Is:7888 For 25% Compression. The Cushioned Back Be Made Of Pu Foam With Polypropylene Injection Molded Plastic Inner. (High Back) Size: 74.0Cm (W) X 74.0Cm. (D). 96.0-116.0Cm (H) X 44.6-58.0Cm Sh. The Armrest Should Be Having Range Of Adjustments, Height Adjustment In The Aluminum Arm Body, Up Down Adjustment, Arm Top Swivel Adjustment At Any Position, Arm Top To And Fro Adjsutment Any Position And Armrest Top Be Made Up Of High Dencsity Pu Moulded Over Glass Filled Poly-Amide Inner. Mechanism The Adjustable Tilting Mechanism Be Designed Having Following Features 360° Revolving Type, Forward Tilt Of Sesat And Back, Upright Tilt Lock, Tilt Tension Adjustment To Be Operated In Seating Position And 3 Position Tilt Limiter.Seat Depth Adjustment Be Housed Below The Seat And Integrated With The Mechanism With Help Of Polypropene Seat Cover. Seat Depthbe Adjusted In Sitting Position. Seat Depth Adjustment Range Be Of 5.0±0.5 Cm.. The Mechanism Be Designed With The Following Features: 360° Revolving Type. 3 Position Locking With Anti Shock Mechanism. Tilt Tension Adjustment. . The Pedestal Be Made Of Die-Cast Aluminium With Buffing Finish With 5 Nos. Twin Wheel Castors. Back Assembly Be Connected To Buff Polish Die Cast Aluminum Spine With An Up-Down Mechanism Assembly. Back Height Should Be Adjusted In Sitting Position. It Can Be Adjusted In The Range Of 7.5±0.5 Cm. , Supplying And Placing In Position Side Unit Of The Following Specifications.1500 X 600 X 610 Top Panel Be Made Of 43Mm Thick (±1) Combination Of Mdf And Particle Board With Top Veneer Facecoated With Clear Lacquer. All Edges Be Edge Banded With Matching 1Mm Thick Veneerlipping. Sliding Shutter Be Made Of 12Mm Thick (±1) Mdf With 3.5Mm Veneer Both Side And Face Coated With Clear Lacquer. All Thickness Edges Be Edge Banded With Matching Lipping. Door Be Provided With Soft Closing & Anti Slam Mechanism. Handle Be Also Provided For Ease Of Opening. Storage Be Secured With Lock. Understructure Be Made Of 18Mm Thick Pre-Laminated Twin Board (Plt) Of E1-P2 Grade And Approvedshade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvclipping. Drawers Be Made Of 18Mm Thick Pre-Laminated Twin Board (Plt) Of E1-P2 Grade And Approvedshade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvclipping. Bottom Panel Of Drawer Be 9Mm Thick Particle Board With Leatherette On Topsurface. Drawers Should Have Soft Closing Channels For Smooth Opening And Closing. , Supplying And Placing In Position Credenza Body Of The Following Specifications Of Size 2400 X 470 X 2325 Construction And Material Be Made From Combination Of Top Panel (0.5Mm Crca), Side Panel (0.5Mm Crca), Bottompanel(0.5Mm Crca For 600W And 0.8Mm Crca For 1200W), Back Panel(0.5Mm Crca),Top Bottom Stiffener(1.2Mm Crca) And End Cover(0.5Mm Crca). Shelves Are 12 Bend Panel Made Of 0.7Mm Thick Crca (D Grade, Is-513). Storage Body Be Powder Coated With Epoxy Polyester To The Thickness Of 50 Microns(+/-10 Micron). Veneer Door Be Made Of 12Mm Thick (±1) Mdf With 3.5Mm Veneer Both Side And Face Coated With Clearlacquer. All Edges Be Edge Banded With Matching 1Mm Thick Veneer Lipping. Door Be Provided With Soft Closing Hinge. Handle Be Also Provided For Ease Of Opening. Storage Be Secured With 3 Way Cam Lock. Glass Door Be Made From The Combination Of Aluminium Alloy (63400) Extrusion And 4Mm Clear Toughened Glass. Aluminium Extrusion Of Glass Doors Are Powder Coated With Epoxypolyester To The Thickness Of 50 Microns (+/-10 Micron). Handle Be Provided For Ease Ofopening. Rh Glass Door Be Provided With 3 Way Cam Lock For Security. , Supplying And Placing In Position Coffee Table Of The Following Specifications.800 X 800 X 320 Top And Bottom Panel:Made Of 36Mm Thick (±1) Combination Of Mdf And Particle Board With Top Veneer Facecoated With Clear Lacquer. All Edges Are Edge Banded With Matching 1Mm Thick Veneer Lipping. Side Panel:Made Of 18Mm Thick Pre-Laminated Twin Board (Plt) Of E1-P2 Grade And Approvedshade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvclipping. Side Panels Are Fitted With Aluminum Trim.Skirting:Made Of 18Mm Thick Pre-Laminated Twin Board (Plt) Of E1-P2 Grade And Approvedshade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvclipping. , Supplying And Placing In Position Side Table Of The Following Specifications Of Size 450 X 450 X 370 Top And Bottom Panel Be Made Of 36Mm Thick (±1) Combination Of Mdf And Particle Board With Top Veneer Facecoated With Clear Lacquer. All Edges Be Edge Banded With Matching 1Mm Thick Veneer Lipping. Side Panel Be Made Of 18Mm Thick Pre-Laminated Twin Board (Plt) Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvclipping. Side Panels Be Fitted With Aluminum Trim. Skirting Be Made Of 18Mm Thick Pre-Laminated Twin Board (Plt) Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvclipping. , Supplying And Placing In Position Conference Table Of The Following Specifications With Overall Size Shall Be3000 X 1150 X 740.Work Top Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Conforming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Access Panels Provided With Soft Closing Hinges Understructure-The Under-Structure Should Consist Of Mixture Of 25Mm And 18Mm Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Conforming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Anodised Aluminium Alloy 63400 - Wp Profile Be Added At Bottom Edges For Improving The Aesthetics. The Product Should Have A Knock-Down Construction. Wire Raiser-A Wire Raiser Be Made Of 0.8Mm Crca Ms Is:513. It Should Be Epoxy Polyester Powder Coated (Dft 40-60 Microns) For Flow Of Wires And Cables. Cutout Provision Below Access Flap At Two Locations For Standard 8 Module Anchor Roma Be Provided. Beside Each Cutout, An Additional Cutout With Plate Be Provided For Mounting Audio Visual Cables (Eg.Hdmi, Vga-A,Etc). , Supplying And Placing Conference Highback Chair Mesh Back Of The Following Specifications.The Seat Be Made Up Of 1.2± 0.1Cm Thk. Hot Pressed Plywood. The Back Be Made Up Of Injection Moulded Glass Filled Nylon & Upholstered Using Net Fabric With High Tenacity Yarn. Seat Size:- 47Cm(W) × 51.5Cm (D). The Hr Polyurathene Foam Be Moulded With Density =55+/-2 Kg/M Cube And Hardness 16± 2 Kgf As Per Is:7888 For 25% Compression. The Armrest Should Have An Up=Down Adjustment Of 8.5 ± 0.5Cm Which Be Provided In Armrest Structure. Armrest Top Should Have An Integrated Layer Of Thermoplastic Elastomer. Armrest Be Made Up Of Plastic Injection Moulded Nylon With Textured Top. It Should Have Front Pivot Synchro Mechanism With Following Features. 360 Degree Revolving Type, Single Point Control, Front Fivot Tilt, Tilt Tension Adjustment, 4 Position Locking With Anti- Shock Feature, Seat/Back Tilting Ration Of 1:2. The Lumber Support Should Consist Of Polypropylene Pad With Mouled Polyurathene Foam & Covered With Polyester Fabric. The Height Of Lumber Padbe Adjusted Through Two Projecting Knobs Provided On The Rear Side Of The Pad. Lumber Pad Should Have An Adjustment Of 8.0± 0.5 Cm In Height. This Shall Come Along A Headrest From Same Family. , Supplying And Placing Conference Midback Mesh Chair Of The Following Specificaiotions. .The Seat Be Made Up Of 1.2± 0.1Cm Thk. Hot Pressed Plywood. The Back Be Made Up Of Injection Moulded Glass Filled Nylon & Upholstered Using Net Fabric With High Tenacity Yarn. Seat Size:- 47Cm(W) × 51.5Cm (D). The Hr Polyurathene Foam Be Moulded With Density =55+/-2 Kg/M Cube And Hardness 16± 2 Kgf As Per Is:7888 For 25% Compression. The Armrest Should Have An Up=Down Adjustment Of 8.5 ± 0.5Cm Which Be Provided In Armrest Structure. Armrest Top Should Have An Integrated Layer Of Thermoplastic Elastomer. Armrest Be Made Up Of Plastic Injection Moulded Nylon With Textured Top. It Should Have Front Pivot Synchro Mechanism With Following Features. 360 Degree Revolving Type, Single Point Control, Front Fivot Tilt, Tilt Tension Adjustment, 4 Position Locking With Anti- Shock Feature, Seat/Back Tilting Ration Of 1:2. The Lumber Support Should Consist Of Polypropylene Pad With Mouled Polyurathene Foam & Covered With Polyester Fabric. The Height Of Lumber Padbe Adjusted Through Two Projecting Knobs Provided On The Rear Side Of The Pad. Lumber Pad Should Have An Adjustment Of 8.0± 0.5 Cm In Height. , Providing, Supplying And Placing Of 2 Seater Sofa Leatherite Finsish With Following Specifications. Overall Size : Width : 132.5Cm, Depth : 81.5Cm, Height : 83.5Cm Upholstery : Synthetic Leather, • Frame : Material Solid Wood Frame With Ply Wood Cross Section Moisture Content : 12% • Foam Density : Seat : 28 Kg/ Cubic Meter • Webbing : S Spring • Legs : Rubber Wood , Providing, Supplying And Placing Of Side Table. Side Table Glass: It Should Be 10 ±0.3 Mm Thick Black Tinted Toughened Glass Uv Glued With Bushes Made In Ss 202 Grade For Focing With Understructure. Side Table Understructure: Should Be Welded Assembly Made In Ss202 Grade Dia. 12±0.04 As Per Is:1762. Width Of Table= 60.0 Cm, Depth=60.0 Cm, Height=34.9 Cm. , Providing And Fixing Modular Conference Table Of Height 740Mm, Having Two Seater Module Of Size 1350X600mm, And Head Module 2350X850mm . Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Conforming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Understructure : It Should Consist Of 18Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Conforming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Aluminium Alloy 63400 - Wp Profile Be Used For Connecting Panels Together. The Product Should Have A Knock-Down Construction. Plastic Abs Access Flap Be Provided For Easy Access To Wires And Cables. Work Top Be Available In Various Shapes. Modesty Panel Be Made Of 18Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Conforming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Powder Coated Accent Metal Strip Provided Below Work Surface To Enhance Aesthetics. It Should Be Of Made Of 0.8Mm Crca As Per Is 513,Epoxy Polyester Powder Coated (Dft 40-60 Microns) Wire Management : An Array Of Panels Made Of 0.8Mm Crca Ms Is:513, Epoxy Polyester Powder Coated (Dft 40-60 Microns) Be Used For Flow Of Wires And Cables. Provision To Mount 6 Module Plate Be Provided Below Worktop. Cutout On Top With Two Piece Injection Moulded Plastic Part Polymer Component Be Fitted To Pull Out Audio,Video Cables Onto Worktop And Connect Devices Charger To Power Socket Below Worktop.. , Providing, Supplying And Placing Of Centre Table. Side Table Glass: It Should Be 10 ±0.3 Mm Thick Black Tinted Toughened Glass Uv Glued With Bushes Made In Ss 202 Grade For Focing With Understructure. Centre Table Understructure: Should Be Welded Assembly Made In Ss202 Grade Dia. 12±0.04 As Per Is:1762. Width Of Table= 112.0 Cm, Depth=60.0 Cm, Height=34.9 Cm. , Sofa 2 Seater Fab Leather Overall Size :Width: 156Cm Depth : 93.5Cmheight : 89Cm Seating Height : 47.5Cm. Stitching: Thread- Polyester. Pitch- 5 Stitch Per Inch( Pitch Of Thread I.E. Stitch Per Inch). Leather/Pvc/Fabric: (Pu/Pvc/Cotton/ Polyester/ Composite)- Fabric:D3/D5/D6 Leather Look Fabric100 Polyester. Thickness (Mm) :0.9Mm. Weight (Gsm) : 250G/M2. Tensile Strength {Wrap/Weft} (Kg/Cm) :Nil. Bursting Strength (Kg/Cm2) :Nil. Colour Fastness To Rubbing {Dry /Wet} (Scale 1-5) :Grade4. Frame Material (Tropical Wood / Pine Wood/ Rubber Wood): Solid Plywood Frame. Moisture Content ( 10 – 12 %) :Less Than12%. Thickness Of Plywood Used(Mm) :9Mm/12Mm/18Mm/30Mm. Standard Of Plywood Used: {Required Standard : Be 303 Commercial Plywood}. Seat Foam: (Density, Type)- Thickness (Mm) :100Mm. Density (Kg/M3):30. Type Of Foam (Virgin/Composite/Moulded/ Slabstock) :Seat Foam:5Cm Pure Foam 3030(30Density)+5Cm Rebond Foam. Covering :Decron Sheet Spec.150G70g. Back Foam: (Density, Type)- Solid Decron 7D/64Mm. Belt/ Webbing Material:Nylon Webbing- Width Of Belt (Mm) :Back:45Mm/Seat:50Mm. , 3 Seater Bench Seat/Back Shell: Should Be Powder-Coated Shell Made From Cold Rolled M.S. Sheet 0.12 ± 0.013 Cm Thickness With Circular Perforations.The Side Bar Be Made Of Cold Rolled M.S.Sheet 0.12 ± 0.013 Cm Thickness. The Shell Be Assembled On The Cross Beam With Help Of M8 Bolts. Seat Size : 50.0 Cm (W) X 45.5 Cm (D) Back Size : 50.0 Cm (W) X 56.0 Cm (H) Cross Beam: It Should Be Made Up Of Cold Rolled Steel With 0.2 ± 0.02 Cm Thickness. The Crossbeam Be Powder Coated. It Should Be Covered With Plastic End Caps Leg: It Should Be Made Up Of Cold Rolled Steel With 0.12 ± 0.013 Cm Thickness. Should Be Powder Coated. The Legs Be Fitted With Leveller Cups Covered With Ss304 Sheet. Armrest: It Should Be Made Of Ss304 Round Tube Of Ø 3.175 ± 0.03Cm X 0.12 ± 0.013 Cm Thick Formed To Make An Oblong Shape. Width (W): 173.5 Cm.Depth (D): 74.0 Cm. Height (H): 91.0 Cm Seat Height (Sh): 44.0 Cm.

Contact Information