|
Tender For Beautification Of Verandah, Facade Lighting Base Work Phase-2 At Kaiserbagh Square Under Smart City Project - Careful removal of existing deteriorated/ damaged/ weathered lime plaster without damaging the surface below it. (S/R) 2 Removing white or color wash by scrapping and sand paperingwithout causing damage to the below stone/brick/plastered surface.and preparing the surface smooth including necessary repairs to scratches etc. complete. (S/R) 3 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. FOR 15 KM (SOR -2020-21) 4 Traditional brick masonry in custom made nanakshahi or lakhori bricks in lime mortar in proportion similar to the existing traditional lime mortar 1:1:1 (lime :1 sand : 1surkhi)Note: The cost may change from region to region due to change in rate of customized bricks. (S/R) 5 Same as above item but for ornamental work ie column and arches (S/R) 6 Repairing ornamental plaster works to match with the existing design using lime plaster (1lime putty:1surkhi:1 Fine sand) (S/R) 7 Stucco Work in lime, surkhi and sand (1:1:1) as per the traditional practices and desing, the mortar should be preparedby grinding mill only. The thickness varies from 10mm to 100 mm as per design. (S/R) 8 Painting of facadein lime and colour wash / artconservator and architect in charge.(S/R) 9 Lime punning with lime putty mixed with Gur,Bilgri,Urd and other ingredients followed by grinding to fine paste for smooth finish .(S/R) 10 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. (DSR-2023/13.62.1) 11 Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. (DSR-2023/15.25) 12 Providing and laying cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded Stone aggregate 40 mm nominal size) including supply of all materials, labour T & P rtc required for proper completion of the work and curing complete also including cost of formwork in foundation & floors. (DSR-2023/4.1.8) 13 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent. (DSR-2023/11.56.1) 14 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. (DSR-2023/13.88) 15 12 mm cement plaster of mix :1:6 (1 cement: 6 coarse sand). (DSR-2023/13.4.2) 16 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr/10 sqm. (DSR-2023/13.48.1) 17 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (DSR-2023/13.80) 18 Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment. (DSR-2023/25.1) 19 Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4 mm thick aluminium composite panel material consisting of 3 mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5 mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone alant, backer rods etc. 20 (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. (DSR-2023/8.32) 21 Providing and fixing 12 mm thick frameless toughened glass of approved brand and manufacture, includingnecessary holes etc. for fixing requiredfittings, all complete as per direction of Engineer-in-charge. (DSR-2023/21.18) 22 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). (DSR-2023/21.18) 23 Excavation infoundation inordinary Soil ( Loam clay or sand ) including lift upto 1.5m lead upto 30.0 m& including filling wateringand rammingof excavated earth into the space between the building & sides offoundation trenches or into the plinth and removal& disposal surplus earthas directed by the engineer I/C within a lead of 30 m.from foundation trenches. (DSR-2023/2.8.1) 24 Providing and laying Cement concrete 1:4:8 (1cement :4 coarse sand :8graded stone ballast 40 mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete, also including cost of formwork in foundation. (DSR-2023/4.1.8) 25 M-150 brick work in foundation 1 : 6 cement and coarse sand mortar in foundation Cement mortar 1:6 (1 cement : 6 coarse sand) (DSR-2023/6.1.2) 26 15mm cement plaster on rough side of single or half brick wall mix 1:5 (1 cement : 4 Coarse sand). (DSR-2023/13.5.1) 27 40 mm thick cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of size 20 mm and below) by laid over baseconcrete finished with floating coat of neat cement (base concrete to be paid separately) including fixing of glass strips. (Excluding cost of glass strips). (DSR-2023/11.3) 28 Providing and fixing stone jali 40 mm thick throughout in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment, matching the stone shade, jali slab without any chamfers etc. (M/R) 29 Pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like. (DSR-2023/14.23) 30 Add for the addition of temporary drainpipe for working at multiple locations (M/R) 31 Add for Cost of Stopping the course of water through the drain by introducing physical barrier as per Engineer in charge. (M/R) 32 Making bell mouth opening/ entrance of size 100x50x50 cm for drainage pipe under footpath, including providing cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) for shape of bell mouth, including plastering providing and fixing precast R.C.C./ S.F.R.C. slab including plastering with cement mortar 1:3 (1 cement : 3 fine sand) of 6 mm thickness on exposed surface of the slab & bell mouth including centring, shuttering & neat cement punning inside the bell mouth etc. all complete. 1 opening every 6m. (DSR-2023/16.49) 33 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 600 mm width X 50 mm depth X 2.0 mm thickness 34 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 600 mm width X 50 mm depth X 2.0 mm thickness 35 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 600 mm width X 50 mm depth X 2.0 mm thickness 36 Supplying and installing of Branding and Signage over Aluminium Composite Panel incuding the cost of printing and designing along with graphics and illustrations in font and language of approved size including the cost of suspended frame work from the existing wall. Also including cost of providing and fixing of fasteners complete in all respects as per Architect in charge 37 Providing, fabricating and fixing/ erection of 6mm Decorative Metal Pendant Sigange including the cost of Ornamental casted bracket at desired location as per approved drawing and design including Designing along with graphics and illustrations in font and language in tentative size of 450*1200mm or as approved. Also including cost of providing and fixing of fasteners complete in all respects as per Architect in charge 38 Supply and fixing of 16 watt spotlight Warm white with Die cast Aluminium Housing painted in wall color ; IP 66 IK 07 with spout for anti glare 635 lumens. Output:Lumens: Various outputs available, depending on the selected LED channel.Efficacy (Im/W): Not specified.LED Channels: Options: 8, 12, 20, 30, 45, 60, 1070 & 520.Electrical: Input Voltage: 100 to 300V AC.Power Consumption: 10 watts (Maximum at full output, steady state).Control Mode: Various options.Interface: Dependent on the chosen control system.Physical:Dimensions (Height x Width x Depth): 176 x 82 x 140 mm.Weight: 1.25 Kgs.Housing Material: High-pressure die-cast aluminum, surface with fluorine carbon spraying.Lens: Toughened Glass.Others:Frequency Range: 50/60Hz.Beam Angle: 100 to 300 degrees.Accessories: Round-Meshed Grill, Honeycomb Grill, Anti-Glare Shield.Luminance in Series: 130.Color Temperature: 3000K/4000K.Vibration Resistance: Yes.Humidity: 10 to 95%. Complete in all respect as approved by Architect by incharge including accessories such as Leader/Jumper cable, connectors, hardware, Packing, forwarding, Handiling, Loading/unloading. (make DarkSpace/Divinity/philips/wipro/halonex/twinkle or equivalent). 39 Supply and Fixing 9-12 Wattage Burial UNIIn Ground- Burial ip68 waterproof BBP343 LED2400/1800/WW 24W/18W 20D 100-240V (Philips/Siems/or Equivalent) 40 POLE LIGHTS Supply ,Installation ,Testing And Commissining OfTwinkle Lites Make 4500-6000 Mm Long Hybrid Decorative Pole With CastedAluminium Base And Ripped Gi Pole PipeWith Decorative Post Top Lantern "Concord" 1270Mm Long With Polycarbonate Diffuser In 60W Led Having Lumn Output Not Less Than 110Lmns/Watt With 10Kva Surge Prtector Designed As Per Architect In-Charge( Make- Twinkle Lite-/-Havells/Neri/Juvaas/Orient/ Thor) 41 Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge ,complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 42 10.00 Sqmm 4 Core 43 25.00 Sqmm 3.5 Core 44 70.00 Sqmm 3.5 Core 45 Supply installation commissioning of following sizes of power and data cable as mentioned: 46 3 x 2.5 sqmm Cu unarmored multistrand 47 5 x 6 sqmm Cu unarmored multistrand 48 4 x 16 sqmm Al armoured 49 3.5 x 95 sqmm Al amrd 50 Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properlyconnected with the earth. 51 16 sqmm (503 i) 52 95 sqmm 53 Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. 54 4 sqmm (504 a) 55 6 sqmm (504 b) 56 16 sqmm (504 d) 57 95 sqmm (504 i) 58 Supply and burring of Safe Earthing Electrode T-19, (Hot Dip Galvanized), Length up to 3000mm, outer Dia 50 mm inner Dia 25 mm, terminal Dia 12mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity 59 S&F of 6 Amp. to 32 Amp. DP MCB (10 KA) C Curve 60 Cable Entry Junction Boxes IP66 HENSEL cat RefDK0606 61 Cable Entry Junction Boxes IP66 HENSEL cat RefKF3535 B 62 Supply, installation, testing and commissioning of Electrical panel with Servo Bypass for all phases. A compartment having two switches for safekeeping the controller and other necessary equipments
|
