1. The Subject Of The Order Is Supply Of A Used Mobile Compost Drum Sifter. 1.2. Detailed Description Of The Subject Of The Order: 1.2.1. Transport Dimensions: 1) Length Up To 10,750 Mm,2) Width Up To 2,400 Mm,3) Height Up To 3,850 Mm.1.2.2. Engine:1) Power 34 Kw - 50 Kw,2) Max Torque 130 - 220 Nm,3) Fuel Tank Capacity Over 200 Dm3,4) Fuel Consumption Approx. 5.5 L/H - 6 L/H,5) The Engine And All Accessories Should Be Placed On A Frame Structure That Can Be Removed From The Machine. To Facilitate Access To The Engine Space, It Should Be Placed At A Height Of Approximately 1.5 M From The Ground.1.2.3. Screen Drum: 1) Diameter 1,800 Mm, 2) Length 4,700 Mm, 3) Mesh Size In The Screen Drum Preferred By The Ordering Party: 25 X 25 Mm, 4) Sieve Sheet Thickness Min. 6 Mm, 5) The Drum Should Be Equipped With A Double System Guiding The Material Inside The Drum Min. 6 Mm,6) Rotational Speed 0-23 Rpm,7) Cleaning Element - Cleaning The Drum With A Brush. The Brush Is Raised And Lowered Hydraulically. 8) The Drive To The Drum Should Be Transmitted Via A Tie-Less Gear. The Drive Must Enable Quick Replacement Of The Screening Drum And Should Guarantee Non-Slip Operation Of The Drum When Screening Wet Compost Or Moist Soil And Ensure A Low Noise Level.9) The Drum Must Be Placed On Wear-Resistant Guide Rollers.1.2.4. Feeding Chamber:1) Volume From 4 M3 To 5 M3,2) Length Up To 3,500 Mm,3) Height Up To 2,760 Mm,4) Width Up To 2,000 Mm,5) Belt Width 1,000 Mm,6) Mechanical Is Required Guiding The Belt Inside The Charging Chamber,7) Drive: Hydraulic Motor With Overload Gear,8) The Device Must Be Equipped With An Overload Control For The Drum Operation, I.E. When Too Much Material Is Introduced Into The Screening Drum, The Introduction Drive Should Automatically Turn Off And Then Automatically Turn On Drive Introduction.1.2.5. Conveyors:1) The Device Is Required To Be Equipped With Two Conveyors For Transporting The Screened Material: For The Under-Sieve Fraction - Side Conveyor And For The Over-Sieve Fraction - Rear Conveyor, 2) Length: Rear ~ 3,000 - 5,000 Mm, 3) Length: Side ~ 5,000 Mm,4) Width: Rear ~800 Mm,5) Width: Side ~800 Mm,6) Speed Of The Transfer Belt - Rear ~0.9 M/S,7) Speed Of The Transfer Belt - Side ~2.9 M/S.1.2 .6. Equipment And Requirements.1) The Machine Is Required To Be Equipped With The Regulation Of Operating Parameters By Changing The Rotational Speed And Changing The Angle Of Inclination Of The Machine,2) It Is Required To Equip The Sieve Components With A System Of Central Lubrication Strips,3) Installing The Machine - On A Two-Axle Trailer,4 ) The Trailer Should Be Equipped With A Ball Hitch For Easy Movement Of The Machine Around The Compost Yard Using A Loader And A 50 Mm Diameter Pass-Through Hitch For Pulling The Machine On Public Roads Using E.G. A Hook Lift. 5) The Machine Should Be Equipped With A Quick Replacement System For The Screening Drum. The Design Should Enable The Replacement Of The Sieve In No Longer Than 20 Minutes.6) Technical Documentation Of The Machine, Operating Manual.1.2.7. Additional Requirements: Subject Of The Order: 1) Must Be Complete, Technically And Functionally Efficient, 2) Must Not Have Any Damage To The Equipment To The Extent That It Prevents Proper Operation, 3) Must Not Have Significant Signs Of Corrosion, Excessive Clearance, Leaks Of Oil And Operating Fluids, 4) It Must Come From Mass Production, It Is Not Allowed To Offer A Device From Unit Production, A Prototype Or A Device From Mass Production Whose Parameters Have Been Specially Changed To Meet The Requirements Specified In This Swz, 5) It Should Be The Property Of The Contractor, 6) It Should Be Free From Defects Physical And Legal,7) Third Parties Cannot Have Rights To It And It Cannot Be The Subject Of Any Proceedings, Including Enforcement And Security Proceedings.1.2.8. Employee Training: 1) As Part Of The Delivery, The Contractor Will Train The Ordering Partys Employees In The Safe Operation, Maintenance And Operation Of The Device, 2) The Training Of Employees Indicated By The Ordering Party Will Take Place On The Day Of Delivery Of The Device To The Ordering Partys Headquarters Located In Poświatne Ul. Pułtuska 5, 09-100 Płońsk Rural Commune.1.2.9. Testing The Compliance Of The Subject Of The Order With The Content Of The Specification And The Submitted Offer: 1) Before Selecting The Most Advantageous Offer, A Committee Appointed By The Ordering Party Will Check The Compliance Of The Technical And Operational Parameters With The Conditions Specified In The Specifications Of The Terms Of The Contract And In The Submitted Offer, 2) The Committee Members Will Inspect And Check The Device At The Contractors Headquarters.3) If It Is Found That The Subject Of The Order Does Not Meet The Requirements Specified By The Ordering Party And In The Submitted Offer, It Will Be Rejected Pursuant To Art. 226 Section 1 Point 5
|