Black Girth - Anatomical Girth For Police, Measuring 95 Cm By 10 Cm Not Including Rings, Made From 40 Thread Greased Leather Sole, Cowhide Lined, In Black, With Two Flat Half Rings 2.5 Inches Wide On The Ends Of The Piece, Duly Reinforced With Another Layer Of 40-Line Sole. White Metal Hardware. Unit., Equestrian Type Loro: With Polypropylene Lace Lining, Must Be Made, In Cow Sole With Double Layer Of Leather Of, At Minimum, 2.5 Mm And, At Maximum, 7 Mm (Each Layer) And A Ribbon Of Inner Nylon Of, 15 Mm And, 17 Mm. 30 Mm And 32 Mm Stainless Steel Buckle With A Finished Stainless Steel Plate Measuring 4 Cm And 4.2 Cm, Joining The Buckle With The Leather And 2 Copper Rivets. The Total Length Of The Loro Will Be 1500 Mm, Finished With 15 Holes For Adjustment. The Occurrence Of Injuries To The Horse Or Even To The Police Officer, Even If Slight, Due To Poor Manufacturing Of The Riding Components, After Or During Their Use, Is A Criterion For Product Disapproval. Par., Pmon Breastplate: The Breastplate Must Be Manufactured, On A Gray Reflective Sole, Containing 2 Parts: The Upper Part, Which Is Fixed To The Saddle With 5 Leather Straps, With The Central Strap Measuring 35 Cm A 38 Cm By 3 Cm To 4 Cm, Lined With High Quality 18-Line Cowhide, With A Metal Ring At Each End, 5 Cm To 6 Cm In Diameter (Which Will Fix The Upper And Lower Straps), And The Strip Central Contains At Each End An Upper Strap Of 35 Cm To 38 Cm By 3 Cm To 4 Cm And A Fold Of 5 Cm And 3 Cm With Buckle And A Lower Strap Of 30 Cm To 33 Cm By 3 Cm To 4 Cm. The Lower Part, Which Will Be Fixed To The Upper Part, Will Contain 03 (Three) Straps Joined By A Central Metal Ring, Measuring 7 Cm To 9 Cm In Diameter, Containing A Leather Protection Measuring 8 Cm To 10 Cm, Lined With Extra Rubber Soft E Vaqueta 18 High Quality Lines, With Two Straps 45 Cm To 48 Cm By 3 Cm To 5 Cm Wide, Containing A Fastening Buckle On Each, And A Strap 100 Cm To 103 Cm By 3 Cm 4 Cm, 40 Cm Of 30 Mm And 80 Cm Of 25 Mm, With A 50 Mm Buckle With Adjustment, For Attachment To The Girth, With A Spring Carabiner At The Tip And 2 Straps With 19 Mm And 21 Mm Buckles For Attachment To The Saddle, With 5.5 Mm Soleplate With High-Gloss Reflective, Gray Measuring 354 Cm X 25 Mm. It Is Important To Emphasize That All Components Must Not Have Burrs Or Allow Contact Between The Metal Parts And The Animals Body To Avoid Injuries. The Occurrence Of Injuries To The Horse Or Is A Criterion For Disapproval Of The Product. Unit., Saddle: Frame – Made Of Light And Resistant Wood (Yellow Garapeira Or Cedrinho), Or Material With Superior Technology That Is Active In The Equestrian Materials Market, All With Good Flexibility And Immunized Against Specific Insects Or Pests. The Frames Head Must Be 28 Cm And 30 Cm High On The Sides, And The Opening From One Foot To The Other Of The Head Must Be 30 Cm For Greater Protection Of The Animals Back. The Side Beams Of The Frame Must Be 35 Cm And 37 Cm From The Inner Beginning Of The Frame To The End Of The Rear Of The Frame. Tab In A Rounded Shape Measuring 29 Cm And 31 Cm Wide At The Sides And 12 Cm And 14 Cm High In The Center Of The Tab. It Must Be Made Of Thin Iron Sheet 2/65 Thick, Measuring 39 Cm By 41 Cm By 17 Mm And 19 Mm Wide, Containing One Piece On Each Side Of The Sides Of The Frame And An Iron Strip With, 65Cm E
|