|
Tender For Miscellaneous Civil Works At 4Th Floor Of Meity- 1 Miscellaneous Civil Works At 4Th Floor Of Meity 2 Dismantling Aluminium / Gypsum Partitions, Doors, Windows, Fixed Glazing And False Ceiling Including Disposal Of Unserviceable Material And Stacking Of Serviceable Material With In 50 Meters Lead As Directed By Engineer-In-Charge. 3 Dismantling Tile Work In Floors And Roofs Laid In Cement Mortar Including Stacking Material Within 50 Metres Lead. For Thickness Of Tiles 10 Mm To 25 Mm 4 Dismantling Wood Work In Frames, Trusses, Purlins And Rafters Up To 10 Metres Span And 5 Metres Height Including Stacking The Material Within 50 Metres Lead : Of Sectional Area 40 Square Centimetres And Above 5 Providing And Fixing False Ceiling At All Height Including Providing And Fixing Of Frame Work Made Of Special Sections, Power Pressed From M.S. Sheets And Galvanized With Zinc Coating Of 120 Gms / Sqm ( Both Side Inclusive ) As Per Is : 277 And Consisting Of Angle Cleats Of Size 25 Mm Wide X 1.6 Mm Thick With Flanges Of 27 Mm And 37Mm, At 1200 Mm Centre To Centre, One Flange Fixed To The Ceiling With Dash Fastener 12.5 Mm Dia X 50Mm Long With 6Mm Dia Bolts, Other Flange Of Cleat Fixed To The Angle Hangers Of 25X10x0.50 Mm Of Required Length With Nuts & Bolts Of Required Size And Other End Of Angle Hanger Fixed With Intermediate G.I. Channels 45X15x0.9 Mm Running At The Spacing Of 1200 Mm Centre To Centre, To Which The Ceiling Section 0.5 Mm Thick Bottom Wedge Of 80 Mm With Tapered Flanges Of 26 Mm Each Having Lips Of 10.5 Mm, At 450 Mm Centre To Centre, Shall Be Fixed In A Direction Perpendicular To G.I. Intermediate Channelwith Connecting Clips Made Out Of 2.64 Mm Dia X 230 Mm Long G.I. Wire At Every Junction, Including Fixing Perimeter Channels 0.5 Mm Thick 27 Mm High Having Flanges Of 20 Mm And 30 Mm Long, The Perimeter Of Ceiling Fixed To Wall / Partition With The Help Of Rawl Plugs At 450 Mm Centre, With 25Mm Long Dry Wall Screws @ 230 Mm Interval, Including Fixing Of Gypsum Board To Ceiling Section And Perimeter Channel With The Help Of Dry Wall Screws Of Size 3.5 X 25 Mm At 230 Mm C / C, Including Jointing And Finishing To A Flush Finish Of Tapered And Square Edges Of The Board With Recommended Jointing Compound , Jointing Tapes , Finishing With Jointing Compound In 3 Layers Covering Upto 150 Mm On Both Sides Of Joint And Two Coats Of Primer Suitable For Board, All As Per Manufacturer"S Specification Andalso Including The Cost Of Making Openings For Light Fittings, Grills, Diffusers, Cutouts Made With Frame Of Perimeter Channels Suitably Fixed, All Complete As Per Drawings, Specification And Direction Of The Engineer In Charge But Excluding The Cost Of Painting With :12.5 Mm Thick Tapered Edge Gypsum Moisture Resistant Board 6 Providing And Applying Plaster Of Paris Putty Of 2 Mm Thickness Over Plastered Surface To Prepare The Surface Even And Smooth Complete. 7 Applying One Coat Of Water Thinnable Cement Primer Of Approved Brand And Manufacture On Wall Surface : Water Thinnable Cement Primer 8 Distempering With 1St Quality Acrylic Distemper ( Ready Mixed ) Having Voc Content Less Than 50 Gms / Litre, Of Approved Manufacturer, Of Required Shade And Colour Complete, As Per Manufacturer"S Specification. Two Or More Coats On New Work 9 Providing Wood Work In Frames Of False Ceiling, Partitions Etc. Sawn And Fixed In Position With Necessary Stainless Steel Screws Etc Sal Wood 10 Providing And Fixing Plain Lining With Necessary Screws / Nuts & Bolts / Nails, Including A Coat Of Approved Primer On One Face, And Fixed On Wooden / Steel Frame Work, Complete As Per Direction Of Engineer-In Charge ( Frame Work Shall Be Paid For Separately ) . 12Mm Thick Commercial Ply Conforming To Is : 1328 Bwr Type 11 Providing & Fixing Decorative High Pressure Laminated Sheet Of Plain / Wood Grain In Gloss / Matt / Suede Finish With High Density Protective Surface Layer And Reverse Side Of Adhesive Bonding Quality Conforming To Is : 2046 Type S, Including Cost Of Adhesive Of Approved Quality. 1.5 Mm Thick 12 Providing And Fixing Wooden Moulded Corner Beading Of Triangular Shape To The Junction Of Panelling Etc. With Iron Screws, Plugs And Priming Coat On Unexposed Surface Etc. Complete 2Nd Class Teak Wood. 50X50 Mm ( Base And Height ) 13 Providing And Fixing 2Nd Class Teak Wood Lipping / Moulded Beading Or Taj Beading Of Size 18X5 Mm Fixed With Wooden Adhesive Of Approved Quality And Screws / Nails On The Edges Of The Pre-Laminated Particle Board As Per Direction Of Engineer-In-Charge 14 Providing And Laying Vitrified Floor Tiles In Different Sizes ( Thickness To Be Specified By The Manufacturer ) With Water Absorption Less Than 0.08% And Conforming To Is: 15622, Of Approved Make, In All Colours And Shades, Laid On 20Mm Thick Cement Mortar 1:4 ( 1 Cement : 4 Coarse Sand ) , Jointing With Grey Cement Slurry @ 3.3 Kg / Sqm Including Grouting The Joints With White Cement And Matching Pigments Etc., Complete. Size Of Tile 600X600 Mm 15 Providing And Fixing 19Mm Thick Both Side Balancing Laminationfactory Pressed Bwp Grade Marine Ply As Per Is 710 Of Approvedbrand Boxes, Shelves, Racks, Almirah, Cupboard And Drawer Etc.Including Necessary Nails, Screws Etc. Complete As Per Directionof Engineer-In-Charge. 16 Providing And Fixing Cupboard Shutter With 19Mm Thick One Sidedecorative And Other Side Balancing Lamination Factory Pressedbwp Grade Marine Ply As Per Is 710 Of Approved Brand Including2mm Thick Pvc Edge Banding Tape With Hot Glue By Edge Bendingmachine Etc. With Auto Closing Spring Loaded Hinges ( Hydraulictype ) Etc. Complete As Per Direction Of Engineer In-Charge. ( Payment Of Providing And Fixing Auto Closing Hinges Shall Be Paid Separately ) 17 Providing And Fixing Stainless Steel Fancy Handle Of Approvedmake Fixed With Ss Screws Etc. Complete As Per Direction Ofengineer-In-Charge200 Mm 18 Providing And Fixing Stainless Steel Soft Closing Spring Hinges At 0Degree Hinges ( Hydraulic Type ) Of Approved Make / Brand Tocupboard Shutters With Full Threaded Steel Screws Includingmaking Necessary Recess In Board And Finished Etc. Complete Asper Direction Of Engineer-In-Charge. 19 Providing And Fixing 2Mm Thick 16 To 19Mm Wide Pvc Edge Bindingtape Of Approved Quality For Cupboard / Wardrobe Shuttersincluding Necessary Synthetic Resin Hot Pressed To Edges On Binding Machine Etc. Complete As Per Directions Of Engineer- In-Charge. 20 Providing And Fixing Magnetic Catcher Of Approved Quality In Cupboard / Ward Robe Shutters, Including Fixing With Necessary Screws Etc. Complete. Triple Strip Vertical Type 21 Providing And Fixing Chromium Plated Brass 50 Mm Cupboard Or Wardrobe Knobs With Nuts Complete 22 Polishing In High Gloss / Matt Finish Melamine Clear Polish On Wood Work In Required Color / Wooden Shade Texture With Following Process In The Sequence As Detailed Below: The Surface To Be Polished Is Rubbed With Sand Paper 80 / 120 No. And Then With Sand Paper Of 160 / 180 Nos. Applying Two Coats Of Sealer With Spray Gun And Allowing Sufficient Drying Time For 1St Coat And 2Nd Coat Is Allowed To Dry For 8 To 12 Hrs On Drying Of Sealer Coat, Wet Rubbing With Emery Cloth Of Finer Grading With Ample Water To Remove Excess Sealer, Layer And Make The Surface Further Smooth After This Wet Rubbing, Then Surface Is Applied With Special Grade Melamine Fillers To Fill All The Small And Bigoles / Grooves Etc. Filler Coat To Be Allowed To Dry For 4 To 6 Hrs On Which Again A Light Wet Rubbing Is Done This Surface Is Further Allowed To Dry For 12 Hrs. On This, 1St Coat Of Melamine Polish Is Applied With Spray Gun Using Melamine Clear Polish And Melamine Thinner In Required Proportion. This 1St Coat Is Allowed To Dry For 24 Hrs Then This Dry Surface Is Again Fine Wet Rubbed Smooth, Which Is Further Allowed To Dry For 12 Hrs. The Final Melamine Polish Is Applied With Compressor Pressure Spray Gun Using Melamine Clear Polish And Melamine Thinner Mixed In Required Proportion Complete As Per Direction Of Engineer-In-Charge. ( Final Coat To Be Done In 1 Or 2 Layers Without Gap Of Time. ) 23 Dismantling Wooden Boardings In Lining Of Walls And Partitions, Excluding Supporting Members But Including Stacking Within 50 Metres Lead : Thickness Above 10 Mm Up To 25 Mm 24 Thickness Above 25 Mm Up To 40 Mm 25 Providing Wood Work In Frames Of Doors, Windows, Clerestory Windows And Other Frames, Wrought Framed And Fixed In Position With Hold Fast Lugs Or With Dash Fasteners Of Required Dia & Length ( Hold Fast Lugs Or Dash Fastener Shall Be Paid For Separately ) . Second Class Teak Wood 26 Providing And Fixing Isi Marked Flush Door Shutters Conforming To Is :2202 ( Part I ) Non-Decorative Type, Core Of Block Board Construction With Frame Of 1St Class Hard Wood And Well Matched Commercial 3 Ply Veneering With Vertical Grains Or Cross Bands And Face Veneers On Both Faces Of Shutters: 30Mm Thick Including Isi Marked Stainless Steel Butt Hinges With Necessary Screws 27 Providing And Fixing Aluminium Tower Bolts, Isi Marked, Anodised ( Anodic Coating Not Less Than Grade Ac 10 As Per Is : 1868 ) Transparent Or Dyed To Required Colour Or Shade, With Necessary Screws Etc. Complete : 200X10 Mm 28 Providing And Fixing Aluminium Hanging Floor Door Stopper, Isi Marked, Anodised ( Anodic Coating Not Less Than Grade Ac 10 As Per Is : 1868 ) Transparent Or Dyed To Required Colour And Shade, With Necessary Screws Etc. Complete. Single Rubber Stopper 29 Providing And Fixing Aluminium Die Cast Body Tubular Type Universal Hydraulic Door Closer ( Having Brand Logo With Isi, Is : 3564, Embossed On The Body, Door Weight Upto 35 Kg And Door Width Upto 700 Mm ) , With Necessary Accessories And Screws Etc. Complete 30 Providing And Fixing Bright Finished Brass 100 Mm Mortice Latch And Lock With 6 Levers And A Pair Of Lever Handles Of Approved Quality With Necessary Screws Etc. Complete. 31 Providing And Fixing Aluminium Handles, Isi Marked, Anodised ( Anodic Coating Not Less Than Grade Ac 10 As Per Is : 1868 ) Transparent Or Dyed To Required Colour Or Shade, With Necessary Screws Etc. Complete : 125 Mm 32 Providing And Fixing Glazing In Aluminium Door, Window, Ventilator Shutters And Partitions Etc. With Epdm Rubber / Neoprene Gasket Etc. Complete As Per The Architectural Drawings And The Directions Of Engineer-In-Charge . ( Cost Of Aluminium Snap Beading Shall Be Paid In Basic Item ) : With Float Glass Panes Of 5 Mm Thickness ( Weight Not Less Than 12.50 Kg / Sqm ) 33 Providing And Fixing 12Mm Thick Frameless Toughened Glass Door Shutter Of Approved Brand And Manufacture, Including Providing And Fixing Top & Bottom Pivot & Double Acting Hydraulic Floor Spring Type Fixing Arrangement And Making Necessary Holes Etc. For Fixing Required Door Fittings, All Complete As Per Direction Of Engineer In Charge ( Door Handle, Lock And Stopper Etc. To Be Paid Separately ) 34 Providing And Fixing False Ceiling At All Heights With Integral Densified Calcium Silicate Reinforced With Fibre And Natural Filler False Ceiling Tiles Of Size 595X595mm Of Approved Exture, Design And Patterns As Per Cpwd Specification 2019, To Be Laid In True Horizontal Level Suspended On Inter-Locking Metal T-Grid Of Hot Dipped Galvanised Iron Section Of 0.33Mmthick ( Galvanized @ 120 Grams Per Sqm Including Bothides ) Comprising Of Main-T Runners Of Size 24X38 Mm Of Length 3000 Mm, Cross - T Of Size 24X32 Mm Of Length 1200 Mm And Condaryintermediate Cross-T Of Size 24X32 Mm Of Length 600Mm To Formgrid Module Of Size 600 X 600 Mm, Suspended From Ceiling Usinggalvanised Mild Steel Items ( Galvanizing @ 80 Grams Per Sqm ) I.E. 12X50 Mm Long Dash Fasteners, 6 Mm Dia Fully Threaded Hanger Rod Upto 1000 Mm Length And L-Shape Level Adjuster Of Size 76X25x25x1.6 Mm Fixed With Grid And Z Cleat Of Size 25X37x25x1.6Mm Thick With Precut Hole On Both 25Mm Flange To Pierce Into 12X50mm Or Even Bigger Size Dash Fastener If Require, Fixed With Glavanised Iron Perimeter Wall Angle Or Size 24X24x0.40 Mm Of Length 3000 Mm To Be Fixed On Periphey Wall / Partition With The Help Of Plastic Rawl Plugs At 450Mm Center To Center And 40 Mm Long Dry Wall S.S Screws. The Workshall Be Carried Out As Per Specifications, Drawing And As Per Directionsof The Engineer-In Charge With 15 Mm Thicktegular / Butt Edged Without Perforation Plain / Designer Light Weight Calcium Silicate Anti-Microbialbio-Safe Coated False Ceiling Tiles Confirming Jis-Z2801and Astm G-21 35 Mirror Polishing On Marble Work / Granite Work / Stone Work Where Ever Required To Give High Gloss Finish Complete. 36 Painting With Synthetic Enamel Paint Of Approved Brand And Manufacture Of Required Colour To Give An Even Shade : Two Or More Coats On New Work Over An Under Coat Of Suitable Shade With Ordinary Paint Of Approved Brand And Manufacture 37 Providing And Fixing Plywood 4 Mm Thick, One Side Decorative Veneer Conforming To Is: 1328 ( Type-1 ) , For Plain Lining / Cladding With Necessary Screws, Including Priming Coat On Unexposed Surface With Decorative Veneer Facings Of Approved Manufacture 38 Renewing Glass Panes, With Wooden Fillets Wherever Necessary: Float Glass Panes Of Nominal Thickness 5 Mm ( Weight Not Less Than 12.5Kg / Sqm ) 39 Disposal Of Moorum / Building Rubbish / Malba / Similar Unserviceable, Dismantled Or Waste Material By Mechanical Transport Including Loading, Transporting, Unloading To Approved Municipal Dumping Ground For Lead Upto 20 Km For All Lifts, Complete As Per Directions Of Engineer-In-Charge. 40 Providing And Fixing Aluminium Work For Doors, Windows, Ventilators And Partitions With Extruded Built Up Standard Tubular Sections / Appropriate Z Sections And Other Sections Of Approved Make Conforming To Is: 733 And Is: 1285, Fixing With Dash Fasteners Of Required Dia And Size, Including Necessary Filling Up The Gaps At Junctions, I.E. At Top, Bottom And Sides With Required Epdm Rubber / Neoprene Gasket Etc. Aluminium Sections Shall Be Smooth, Rust Free, Straight, Mitred And Jointed Mechanically Wherever Required Including Cleat Angle, Aluminium Snap Beading For Glazing / Paneling, C.P.Brass / Stainless Steel Screws, All Complete As Per Architectural Drawings And The Directions Of Engineer-In-Charge. ( Glazing, Paneling And Dash Fasteners To Be Paid For Separately ) : For Fixed Portion Powder Coated Aluminium ( Minimum Thickness Of Powder Coating 50 Micron ) 41 For Shutters Of Doors, Windows & Ventilators Includingproviding And Fixing Hinges / Pivots And Making Provisionfor Fixing Of Fittings Wherever Required Including The Cost Of Epdm Rubber / Neoprene Gasket Required ( Fittings Shall Be Paid For Separately ) Powder Coated Aluminium ( Minimum Thickness Of Powder Coating 50 Micron ) 42 Providing And Fixing Stainless Steel ( Ss 304 Grade ) Adjustable Frictionwindows Stays Of Approved Quality With Necessary Stainless Steelscrews Etc. To The Side Hung Windows As Per Direction Of Engineer In-Charge Complete. 255 X 19 Mm 43 Providing And Fixing Aluminium Casement Windows Fastener Of Required Length For Aluminium Windows With Necessary Screws Etc. Complete. Powder Coated Minimum Thickness 50 Micron Aluminium 44 Providing And Fixing Wooden Moulded Beading To Door And Window Frames With Iron Screws, Plugs And Priming Coat On Unexposed Surface Etc. Complete :2Nd Class Teak Wood 50X12 Mm 45 Providing And Fixing Ss 304 Glass Shutter Pull Handle D-Type ( 32X600 Mm ) For Make Godrej / Hardwyn / Ozone Or Equivalent Brand As Approvedcompleteasperdirectionof Engineer-In-Charge. 46 Providing And Fixing Special Quality Bright Finished Glass Shutter Bottom Locks Patch Complete With. For Make Godrej / Hardwyn / Ozone Or Equivalent Brand As Approved Completeasperdirectionof Engineer-In-Charge. 47 Providing And Fixing 12Mm Thick Plain Toughened Glasspartitions Complete Including Necessary Stainless Steel U Channel, Brackets, Connectors, Silicon Etc. Of Approved Make Etc. Complete As Per Direction Of Engineer-In-Charge. 48 Providingandfixingsuncontrolfilm Make 3M / Garware / Equivalent Brand As Approved By Engineer-In- Chargeforglasswindow / Doors / Partition Etc.Inapproved Design And Pattern As Per Direction Of Engineer-In- Charge.
|
