This Is A Combined Synopsis Solicitation For Commercial Items Prepared In Accordance With The Format In Far Subpart 12 6 As Supplemented With Additional Information Included In This Notice Request For Quotations Number Is 70Z08520qp45cleat And Is Issued As A Request For Quotations Rfq This Announcement Constitutes The Only Solicitation Quotations Are Being Requested And A Written Solicitation Will Not Be Issued This Request For Quotations Incorporates Provisions And Clauses In Effect Through Federal Acquisition Circular 2005 84 Dated Nov 1 2015 The Naics Code Is 336611 The Small Business Size Standard Is 1250 This Is A Total Small Business Set Aside All Responsible Sources May Submit Proposals That Will Be Considered By The Agency The Contract Will Be Awarded On A Firm Fixed Price Basis Using Simplified Acquisition Procedures In Accordance With Far Part 13 5 For Purposes Of Evaluation And Award Past Performance Is Considered To Be More Important Than Price Offerors Shall Submit Quotes As Follows Date June 12Th 2020 Time 0800 Pacific Standard Time Pst Place William A Swordjr Uscg Mil Required Documents Each Offeror Shall Furnish The Information Required By The Solicitation Which Includes Section 1 Price Quote Including Cost Breakdown Section 2 Past Performance References Proposal This Section Should Include The Offerors Completed Representations And Certifications And Section 3 Any Issued Amendments To The Solicitation Anticipated Award Date The Contract Is Subjective To Availability Of Funds This Is To Collect Potential Bids To Price Out The Service That Will Late Be Funded Based Off Of Collected Bids Questions The Last Day To Ask Questions Will Be June 12Th 2020 0800 Pacific Standard Time Pst Questions Shall Be Submitted Via E Mail To William A Swordjr Uscg Mil After This Date Unless Amended Questions Will Not Be Accepted For Information Regarding This Solicitation Please Contact William Sword 510 637 5901 Please Note Amendments To This Solicitation Will Be Publicized In The Same Manner As The Initial Synopsis And Solicitation Questions And Quotes Shall Be Emailed To William A Swordjr Uscg Mil Contractors Are Responsible For Verifying Receipt Of Quotes Interested Vendors Please Send Official Quote With A Sam Gov Registered Duns Number And Email To William A Swordjr Uscg Mil Statement Of Work Magnetic Survey Of Us Coast Guard Cutter Cleat Part I General Information Introduction And Background The Uscgc Cleat Is Facing Recurring Problems Correcting Deviation Of Its Magnetic Compass Which It Currently Uses As The Primary Instrument For Steering Heading Indication Leading To The Cutter Being Unable To Conduct Its Mission The Difficulties Were First Noticed After The Completion Of A Drydock Repair In Baltimore Maryland During This Repair Period It Has Been Verified By The Port Engineer That 1500 Sq Ft Of Hull Metal 200 Feet Of Framing And Over 90 Of The Wiring On The Cutter Was Replaced Such Repairs Especially Those As Extensive As This Are Known To Have A Significant Impact On The Magnetic Field Of Steel Hull Vessels And Can Continue To Change For Years After The Completion Of Repairs In The Experience Of Professional Compass Adjusters A Vendor Is Requested To Submit Proposals For Magnetic Survey On Board The Uscgc Cleat And Uscgc Chock In Order To Determine The Source Of The Magnetic Anomalies Causing Inaccuracy Of The Magnetic Compass Scope The U S Coast Guard Uscg Is Seeking A Vendor Capable Of Conducting A Shipboard Magnetic Survey Survey Will Take Place On Board 2 Wytl Class Coast Guard Cutters Both Uscgc Cleat And Uscgc Chock For Purposes Of Comparison Contractor Must Be Capable Of Conducting The Survey According To Industry Best Practices Analyzing The Data Collected From The Survey And Available To Propose Treatment Actions For Sources Of Magnetic Interference Or To Continue To Conduct Follow On Investigations As Requested By The Government Optional Work That May Be Included At The Discretion Of The Government In The Scope After The Initial Survey Pending Availability Of Funds And Approval Of The Contracting Officer Ko Demagnetization Also Called Degaussing Or Deperming Of An Isolated Magnetic Source On Board Uscgc Cleat Found During The Survey Conduct Underwater Measurement Of The Permanent Magnetism Of The Cleat S And Chock S Hull Conduct Follow Up Investigations Or Readings If Needed Documentation Coast Guard Drawings 65B Wyt 0103 5 Rev C Us Coast Guard 65 Foot Steel Tug Boat B Class Inboard And Outboard Profiles 65 Wyt 6700 1 Rev A 65 Foot Wyt Pilothouse Arrangement Of Electronic Configuration And Antenna Equipment Coast Guard Documents Surface Forces Logistics Center Standard Specification 0000 Sflc Std Spec 0000 2018 General Requirements Surface Forces Logistics Center Standard Specification 0860 Sflc Std Spec 0860 2018 General Requirements For Technical Publication Preparation Surface Forces Logistics Center Technical Standard 086 Comdtinst M9085 1C Naval Engineering Computer Aided Design Standards 11 12 2011 Government Technical Publications Dod Std 2143 Sh Magnetic Silencing Requirements For The Construction Of Non Magnetic Ships And Craft 1 June 1983 Dod Std 2141 Sh Definitions And Systems Of Units Magnetic Silencing Metric 1 June 1983 Dod Std 1399 Section 070 Part 1 Interface Standard For Shipboard Systems 26 February 1979 Mil Dtl 24643 3E Detail Specification Sheet Electrical Cable 1 October 2009 Mil Std 2142A Sh Magnetic Silencing Characteristics Measurement Of Metric 6 August 1990 Naval Ships Technical Manual S9086 Qn Stm 010 Chapter 475 Magnetic Silencingnaval Ships Technical Manual S9086 Nz Stm 010 Chapter 420 Navigation Systems Equipment And Aids Opnav Inst C8950 2G Magnetic And Acoustic Signature Control For Mine Warfare Miw 28 February 2002 Other Documents Iso Iec 17025 2005 General Requirements For Testing And Calibration Laboratories Ansi Ncsl Z540 3 2006 Requirements For The Calibration Of Measuring And Test Equipment Ieee Standard 1308 1994 Recommended Practice For Instrumentation Specifications For Magnetic Flux Density And Electric Field Strength Meters 10 Hz To 3 Khz Ieee Standard 1460 1996 Ieee Guide For The Measurement Of Quasi Static Magnetic And Electric Fields Part Ii Work Requirements Work Required The Contractor Shall Provide The Following Services And Resources Resources Amp Equipment Provide The Proper Equipment And Personnel Needed To Perform The Work Resumes For Technicians Participating In The Contract Shall Be Submitted Proving Their Relevant Prior Experience The Contractor Is Responsible For Identifying And Providing Equipment Capable Of Measuring Magnetic And Static Electric Fields According To Sensitivity And Accuracy Requirements Defined In Opnav Inst C8950 6G And Ieee Std 1308 When Optional Services Of This Contract Are Activated The Additional References Nstm 475 And Ieee Std 1460 Must Be Consulted For Planning Deperming And Any Hull Magnetism Survey Magnetic Survey In Both Underway And Moored Configurations Survey On Board Locations And Equipment Which Are Likely Sources Of Magnetic And Electric Fields According To Industry Experience Nstm 420 And Ieee Std 1460 The Contractor Shall Independently Determine Measurement Points According To The References Noted Above And Lead The Survey According To Their Understanding Of The Problem Record Data Systematically Noting Carefully The Location And Nameplate Data For Each Measurement Being Made Optional Upon Completion Of The Survey And Report Submissions And If Approved By The Ko Make Follow Up Visit To Conduct Underwater Measurement Of The Hull Magnetism For Both The Cleat And The Chock Using Guidance From The References In Section 3 Document The Procedures Performed Including The Tools Resources Required So The Process Can Be Repeated Again On Other Assets As Needed Author A Technical Publication Summarizing The Instruments Used To Collect The Data The Methodology Used To Determine The Position Of Readings Taken And Basic Methods Of Interpreting Raw Data From Magnetic Surveys The Publication Format Must Comply With Sflc Std Spec 0860 Sflc Technical Std 086 And Section 6 Below Reports And Data Conduct Analysis Of The Data Collected In Accordance With Sflc Std Spec 0860 Sflc Technical Std 086 And Section 6 Below A Summary Trip Report Shall Be Submitted Explaining The Measurement Locations And Presenting The Raw Data Collected Analysis Of The Data Must Be Conducted To Show Quantitatively The Most Likely Sources Causing Magnetic Deviation Of The Compass In Case No Definitive Sources Can Be Located Or Ambiguity Exists General Interpretation Of The Data Or Other Theories May Be Advanced With Proper Support Of The Data In The Recommendations Section Of The Report Identify Isolated Magnetic Or Electric Field Sources Located During The Survey Especially Those Relevant To Magnetic Compass Deviation Treatments Or Repair Should Be Recommended And Quoted As Applicable According To Contractor S Ability To Conduct Follow On Procedures Optional In The Event Follow Up Visits With Additional Data Collection Submit Summary Trip Reports For Each Visit With The Same Formats And Requirements Stated Above As An Addendum Referencing The Original Report Demagnetize Optional On A Follow Up Visit Pending Availability Of Funds And Approval Of The Ko On Board Uscgc Cleat Demagnetize Via Induced Magnetic Field Isolated Component Sources Of Magnetic Fields Located During The Survey Provide Equipment Nomenclature And Specifications Used In The Demagnetization Process Provide Schematic Diagrams And Procedures For Proposed Demagnetization Travel Travel Costs For Contractor S Personnel Shall Be Included In The Proposed Service As A Separate Line Item Technical Documentation Content For Technical Documentation Technical Publications And Drawings To Be Provided Shall Be As Defined Herein And In Accordance With Sflc Technical Standard 086 Each Document Shall Include A Data Rights Release That Allows Publication On The Coast Guard Intranet And Distribution To The Fleet Additional Requirements For The Content Of Technical Documentation Shall Be As Identified In Section 7 Deliverables Technical Publications Tp All Tps Provided Under This Contract Shall Be Provided In Microsoft Word Format And Delivered To The Ko Technical Publications Shall Be Delivered By Email In Unlocked And Unencrypted Adobe Acrobat Pdf Format Chapters Sections Major Paragraphs Parts Lists Drawings Figures And Appendices Shall Be Hierarchically Indexed With Bookmarks Text On All Sheets Except Drawings And Photographs Shall Be Searchable When Practicable A Copy Of All Source Documents Used To Prepare The Pdf Shall Also Be Provided In Their Native Editable Format Such As Microsoft Office Doc Xls Or Mdb Or Autocad Dwg Technical Publications Should Include As Applicable Cover And Title Page Contractor S Name And Address Table Of Contents Including A List Of Drawings And Tables Safety Precautions Cautions Warnings And Notes General Theory Of Operation Preparation Installation And Initial Adjustment Instructions Operational Instructions Performance Verification And Test Features Troubleshooting Instructions Disassembly Repair Replacement And Reassembly Instructions Installation Instructions Diagrams Illustrations And Schematics Parts List Data The Parts List Will Identify All Components And Assemblies Necessary To Perform The Work The Following Requirements Apply To The Parts List Original Equipment Manufacturer Oem Part Number Oem Commercial And Government Entity Cage Code If Available Or Oem Description Address And Telephone Number All Parts Shall Be Keyed Using Index Numbers To Exploded View Drawings Parts In The Listings Shall Be Grouped By Assemblies Subassemblies And Modules Parts Shall Be Identified In The Assembly In Which They Are Components Final Deliverable One 1 Electronic Copy Of The Coast Guard Approved Technical Publication Shall Be Provided To The Cor By Email Electronic Files Shall Be Provided For The Government S Technical Library And Shall Include All Source Files Used To Produce The Technical Publication Deliverables Documents In This Section Are To Be Delivered Via Email To The Ko Within 30 Days Of Site Visit Completion Execution Of The Service Portion Of Deliverables Shall Be Agreed With The Ko At The Time Of Awarding Qualified Personnel And Equipment To Conduct The Magnetic Survey Arranging Travel If Needed For Completion Of The Contracted Work Execution Of The Magnetic And Electric Field Survey As Detailed In Section 4 Final Summary Trip Report Including Raw Data And Analysis Recorded And Collated According To The References In Section 3 And Meeting The Requirements Of The Work Detailed In Section 4 Addendums To Trip Report Based On Follow Up Visits Magnetic Survey Procedure Documentation As A Technical Publication Part Iii Supporting Information Place Of Performance Homeport Of The Cutters Being Surveyed Us Coast Guard Station 1 Washington Avenue Philadelphia Pennsylvania The Contractor Must Submit Identifying Information For The Technicians Who Will Conduct The Survey Including Name Date Of Birth Id Number And Place Of Issuance Vehicle Registration And Insurance If A Vehicle Is Required Technical Information The Following Vessel Characteristics May Be Relevant To Preparing An Estimate For This Sow The Wytl Is A Steel Hull Tugboat 65 Foot Length 19 Foot Beam 9 Foot Draft The Magnetic Compass Is A Ritchie Globemaster D 5 S Included Quadrantal Correctors Required For Steel Vessels The Wytl Carries A Standard Suite Of Radio Communications Equipment Required For Vessels Of Commensurate Size To Conduct Safe Navigation And Operation Including Both Vhf And Uhf Frequencies Standard Shipboard Equipment Includes Hvac Motors And Pumps Generators Inverters Rectifiers And Both Ac And Dc Distribution Systems If More Complete Description Of The Equipment On Board Is Required Prior To The Visit For Survey Please Submit A Request Through The Ko
Contact Information
Other Detail
View Notice Now...
Fill Detail for Getting Instant Access
Download Tender Document / Tender Notice
Dear Sir,
Warm Greetings from TenderDetail.com !!
We have received Tender Document request for the TDR No : 30474943
Tender Notice along with it's Attachments ( Tender Document / Scan Image of News Paper)
sent to your Email Address :.
Please check your email for Tender Document.