|
Frame Slipway The Delivery Set Includes Installation And Connection. Platform Size 5200X2100mm. Load Capacity 3500 Kg. The Presence Of A Movable Support Allows You To Move The Slipway Around The Workshop. Using A Movable Support As A Platform Lifting Device. Does Not Require Electricity. All Operations Are Performed Using Compressed Air. Attaching Traction Towers Directly To The Frame At Any Point. Along The Entire Surface Of The Slipway There Are The Necessary Mounting Points For The Body Clamps. Two Carts For Rolling Up A Car With Damaged Wheels. Two Traction Towers With A Force Of 10 Tons Each. The Angle Of Application Of Force Is 360 Degrees. Contents: Platform – 1 Pc. Traction Tower With Chain And Hook – 2 Pcs. Pneumohydraulic Pump – 2 Pcs. Drive-In Ramps – 2 Pcs. Beam For Straightening The Roof – 1 Pc. Body Clamps – 4 Pcs. Rolling Cart – 2 Pcs. Support Support Posts – 2 Pcs. Chain Stop – 1 Pc. Set Of Clamps And Hooks. Technical Passport Operating Instructions Book Compliance With Technical Regulations/Standards Of The Republic Of Kazakhstan, The Delivery Set Includes Installation And Connection. 6 Operating Minimum Part Length 100 Mm Minimum Part Width 60 Mm Panel Thickness From 10 To 55 Mm Edge Width From 12 To 54 Mm Edge Thickness From 0.5 To 5 Mm Feeding Speed 8-10-12 M/Min Total Installed Power / Voltage 4.94 Kw / 380 V, 50 Hz Air Pressure 6 Bar Overall Dimensions B3150x1100x1350 Mm Designed For Gluing Pvc, Abs, Melamine Edges Up To 5 Mm Thick On The Straight Ends Of Furniture Parts Made Of Chipboard, Mdf, Plywood. Heated Guide Plate - Dries And Heats The End Of The Part, Which Promotes Better Adhesion Of The Edge. Touchscreen Control Panel (Delta) - Simple And Intuitive Control Of Each Unit, Counter For The Number Of Parts And Edge Length. Motorized Lifting / Lowering Of The Pressure Beam - The Machine Is Adjusted To A Different Thickness Of Parts From The Control Panel. The Part Pre-Launch Protection System Will Prevent The Operator From Starting The Workpiece Ahead Of Time. Pre-Cutting And Edge Gluing Unit. Glues Evenly And Continuously. Automatic Control Of Glue Supply. Easy Adjustment For Different Edge Thicknesses. Special Spiral Design Of The Glue Tank. Trimming Knot. Infrared Sensors; Separate Trimming Of Front And Rear Overhangs. Two High Frequency Motors. 12’000 Rpm Milling Unit For Removing Overhangs. Separate Processing Of The Upper And Lower Parts. Two High Frequency Motors. 12’000 Rpm Radius Scraping Unit With Carbide Knives, Corrects The “Wave” Effect, Removes Excess Glue The Edge Polishing Unit, Driven By Two Motors, Finishes The Part. Operating Instructions Book, The Delivery Set Includes Installation And Connection. Length Of The Moving Table, Mm 3200 Movable Table Travel, Mm 3200 Width Of Movable Table, Mm 375 Saw Angle 90° (Without Tilt) Largest Saw Diameter, Mm 305 Cutting Height, Mm 70 Diameter Of Cutting Blade, Mm 120 Saw Spindle Diameter, Mm 30 Scoring Blade Spindle Diameter, Mm 20 Desk Dimensions, Mm 950 X 550 Distance (Maximum) Between The Saw And The Side Base Ruler, Mm 1150 Engine, Kw 5 Scoring Device Motor, Kw 0.75 Saw Speed, Rpm 5000 Scoring Blade Speed, Rpm 8300 Diameter Of The Chip Receiver Pipe Of The Saw Unit / Main Saw Guard, Mm 100 / 60 Total Installed Power, Kw 5.75 Operating Instructions Book, The Delivery Set Includes Installation And Connection. Height, Mm1100 Length, Mm 1060 Number Of Spindles, Pcs. 21 Power, Kw 1.5 Spindle Speed, Rpm 2800 Working Area For The Machine, Mm3500 X 3500 Desk Dimensions, Mm 890 X 625 Distance Between Outer Spindles, Mm 640 Distance Between Spindles, Mm 32 Required Air Pressure, Bar6 Traverse Angle, °0 - 90 Width, Mm 1050 Pneumatic System Pressure, Bar6-8 Operating Instructions Book, The Delivery Package Includes Installation And Connection. The Chamber Is Made Of Sandwich Panels, Painted With Powder Paint, Coated On The Inside With A Special Anti-Reflective Coating. The Chamber Is Equipped With Three-Leaf Swing Gates. There Is A Side Door For Personnel. Camera Includes: One Heat-Generating Group, Equipped With: A Turbine-Type Supply Fan With A Capacity Of 24,000 M³, A 7.5 Kw Electric Motor, A Pneumatic Recirculation Damper, And A Group Of Pre-Air Filters. The Heat Generator Group Is Equipped With A Riello 40G20 Diesel Burner. One Extractor Group Equipped With An Exhaust Fan With A Capacity Of 20,000 M³/H And A 5.5 Kw Electric Motor. Automated Process Of Switching Painting\Blowing\Drying\Cooling Modes. The Chamber Is Equipped With Filters: Pre-Filter, Ceiling Fine Filter, Floor Filter Paint-Stop G3. The Chamber Has A Top Inclined And Side
|
