|
Tender for Supply Of Electrical And Electronics Engineering Department Lab Equipments Are Required As Per New Syllabus , Upgradation Of Labarotaries Ece Department , 8051 Micro Controller Kit • Operating Voltage: +5 V Dc. • Flash Memory: 4 Kb (At89c51) / 8 Kb (At89s52). • Ram: 128 Bytes Internal Ram. • 16 × 2 Alphanumeric Lcd Display. • Push Buttons / Tactile Switches. • Dip Switches For Digital Input. • Inbuilt Adc Interface: Ldr, Potentiometer. • Inbuilt Dac Interface. • Inbuilt Stepper Motor Driver With Stepper Motor. • Inbuilt Dc Motor Driver With Dc Motor. • 1 × 4 Led Array, 1 × 4 Keypad, 1 × Relay. • 1 × Buzzer, 16 × 2 Lcd Display, 1 × Pwm Driver. • 1 × Hardware Interrupt Key, Inbuilt Rtc. • Inbuilt Eeprom And Uart Module. • 4 × 7-Segment Display. • Supports Both Assembly And C Language Programming. • Pc Interfaceable. , Single Phase Induction Motor 1 Hp, 230 V Ac, 1500 Rpm With Loading Arrangement - 1 No. Voltmeter: (0-300) V Ac, 96 × 96 Mm With Input Terminals - 1 No. Ammeter: (0-10) A Ac, 96 × 96 Mm With Input Terminals - 1 No. Wattmeter: 2 Kw, 96 × 96 Mm With Input Terminals - 1 No. Power Factor Meter: 96 × 96 Mm With Input Terminals - 1 No. Auto Transformer: 0-300 V, 1F Variac - 1 No. Mcb: 2-Pole, 40 A / 230 V Ac - 1 No. Digital Rpm Indicator With Proximity Sensor - 1 No. Aluminium Brake Drum: 230 Mm Diameter - 1 No. Spring Balance: (0-25) Kg - 02 Nos. Circuit Diagram Printed On Front Panel With Instruments And Connecting Terminals. Motor And Loading Arrangement Mounted On Rigid Channel Frame With Anti-Vibration Mounting Pads, M12 × 1.5 Bolt & Nut, 85 Mm Dia - 4 Nos. Mild Steel Powder-Coated Electrical Panel Table Setup. , Auto Transformer Input: 230-240 V Ac, 50 Hz. Output: Variable (0-270) V Ac. Rating: 1 Kva. Insulation Class: Class F / Class H. Construction: Copper Winding With Carbon Brush Arrangement. Mounting: Bench-Top / Panel Type. Protection: Suitable Fuse / Overload Protection. , Dth Trainer Kit Power Supply: • 200 V To 240 V Ac, 50 Hz. Dish Antenna: • 1.5 Ft Aluminium Steerable Dish Antenna. Lnb (Low Noise Block Down Converter): • Input Frequency: Ku-Band. • Output Frequency: 950 Mhz To 1450 Mhz. • Conversion Gain: 65 Db. • Noise Temperature: 35 K (Max). Set-Top Box Receiver In Trainer Form: • If Frequency: 70 Mhz. • Video Bandwidth: 50 Hz To 5 Mhz. • Video Output Level: 1 Vpp At 75 O Load. • Video Polarity: Normal/Inverted, Switch Selectable. • Audio Subcarrier Frequency: Tunable From 5.0 Mhz To 8.0 Mhz. • Remote Control Provided. • Hdmi Cable: 10 M. Controls: • Channel Selection. • Volume Control. Fault Simulation: • Five Built-In Simulated Faults For Troubleshooting Experiments. • If Signal Disconnected. • Video Output Fault. • Audio Mute Fault. • Tuner Misalignment. • Rf Output Interruption. Pcb Size: • 15 × 12 With Multicolour Section-Wise Block Diagram. Standard Accessories: • 1.5 Ft Dish Antenna. • Lnb. • Trainer Pcb. • Dish Connecting Wire.• Audio-Video Cable. • User Manual. • Acrylic Cover.• Hardware Materials For Assembly Of Dish Antenna. Additional Features: • Dth Subscription Connection With Doordarshanfree Channels. , Sim Reader Trainer Kit Power Supply: • Operates On 230 V Ac ±10%, 50 Hz Mains Supply. • Built-In Regulated Smps Power Supply. • Operating Dc Supply: 5 V / 12 V With Overload And Short-Circuit Protection. Sim Card Interface: • Supports Gsm Sim Cards Compatible With 2G / 3G / 4G / 5G Networks. • Sim Card Read/Write Interface. • Supports Sim Card Initialization, Authentication, And Communication Functions. • Compatible With Standard 6-Pin / 8-Pin Sim Card Sockets. Communication Interface: • Usb 2.0 Interface For Pc Communication. • Rs-232 Serial Communication Interface. • Uart Communication Facility For Embedded System Interfacing. Sim Operating Parameters: • Selectable Sim Clock Frequencies: • 3.579 Mhz • 7.159 Mhz • 14.318 Mhz • Sim Supply Voltage Selection Facility. • Sim Reset And Activation Control. Supported Protocols And Standards: • Gsm Etsi 07.07 And Etsi 07.05 At Command Support. • Iso/Iec 7816 Smart Card Communication Support. • Sim Communication Command Monitoring Facility. Hardware Features: • On-Board Sim Card Socket. • Led Indication For: • Power Status • Sim Detection • Reset Activity • Data Transmission/Reception • Built -In Keypad For Standalone Operation. • Lcd Display Module (128 × 64) For Menu And Status Display. • On -Board Microcontroller -Based Control Section. Software Support: • At Command Execution And Monitoring Software. • Sim Manager Utility Software.• Data Logging And Communication Terminal Utility. • Pc -Based Gui Software For Sim Data Communication Experiments. Trainer Features: • Fault Simulation Facility For Troubleshooting Experiments. • Simulation Of Faults Such As: • Sim Not Detected • Clock Failure • Vcc Failure • Reset Failure • Multiple On -Board Test Points For Signal Observation. • Test Points For: • Sim_Rst • Sim_Clk • Sim_Io • Vcc • Uart Tx/Rx • Suitable For Cro/Dso Signal Monitoring. • Glass Epoxy Pcb With Educational Block Diagram Layout. • Compact Tabletop Enclosed Cabinet Design. Construction: • Front Panel With Printed Block Diagram.• Banana Test Points And Patching Facility. Standard Accessories: • Gsm Sim Trainer Unit. • Usb Communication Cable. • Rs-232 Communication Cable. • Power Cord. • User Manual. • Utility Software Cd / Downloadable Software Package. , Fpga Trainer Kit • Must Use Industry-Standard Mid-Range Fpga Device • Usb-Jtag Programmable, Compatible With Vivado Ise (Webpack). • Power Supply: 5 V Dc Through Usb Or External Adapter. • On-Board Peripherals: Leds, Switches, Push Buttons, 7-Segment Display,Clock Source, Gpio / Pmod Expansion Ports, Uart, Vga / Hdmi, Usb-Uart Bridge, Usb Cable. •User Manual.
|
