|
Tender for Laying Of One Number Pvc Insulated And Pvc Sheathed / Xlpe Power Cable Of 1.1 Kv Grade Of Following Size In The Existing Masonry Open Duct As Required. Upto 35 Sq. Mm , Laying Of One Number Pvc Insulated And Pvc Sheathed / Xlpe Power Cable Of 1.1 Kv Grade Of Following Size In The Existing Rcc/ Hume/ Metal Pipe As Required. Upto 35 Sq. Mm , Providing And Fixing 6 Swg Dia G.I. Wire On Surface Or In Recess For Loop Earthing Along With Existing Surface/ Recessed Conduit/ Submain Wiring/ Cable As Required , Providing And Laying Earth Connection From Earth Electrode With 6 Swg Dia G.I. Wire In 15 Mm Dia G.I. Pipe From Earth Electrode Including Connection With G.I. Thimble Excavation And Re-Filling As Required. , Earthing With G.I. Earth Pipe 4.5 Meter Long, 40 Mm Dia Including Accessories, And Providing Masonry Enclosure With Cover Plate Having Locking Arrangement And Watering Pipe Etc. With Charcoal/ Coke And Salt As Required. , Supplying And Drawing Following Sizes Of Frls/Hffr Pvc Insulated Copper Conductor, Single Core Cable In The Existing Surface/ Recessed Steel/ Pvc Conduit As Required. 3X1.5 Sqmm , Providing And Laying In Position M25 Grade Reinforced Cement Concrete Foundation Of Size 450 Mm(L) X 450 Mm Wide And 1000 Mm Deep I/C Excavation Of Earth, Providing Cutting, Bending And Placing In Position, Reinforcement Of Cold Twisted Bars Of 12 Mm Dia -960 Mm Long (Approx.) - 8 Nos.And Reinforcement Of Cold Twisted Bar Of 8 Mm Dia - 1400 Mm (Approx.) - 6 Nos. (With 150 Mm Spacing) As Required With Supplying And Positioning Of 4 Nos Foundation Bolts Of Size 16Mm Dia And 600 Mm Long J Type I/C 2 Nos. Template Anchor Plates Of Size 225X225x3 Mm And Providing Dwc Hdpe For Cable Entry & Exit As Required For 3 M And 5 Mtr Pole. , Fabrication, Supply & Erection Of 5.0 Mtr Height, Minimum 3 Mm Thick, Bottom Dia Of 130Mm & Top Dia Of 70Mm, Base Plate Of Size 225 X 225 X 12 Mm Thick Flange Mounted Hot Dip Galvanized Octagonal Pole Made From Ht Steel Plate, Window With Flash Cover With Full Vertical Window Cover At Appropriate Height From The Base Plate On Existing Cement Concrete Pedestal As Required. L/C Supplying And Fixing Of 6 Mm Thick Laminated Mounted Sheet Inside The Window And L/C Providing And Welding 3 Nos. Gi Strips 4 Mm Thick Of Suitable Length And Having Suitable Size Tapped Holes As Reqd, Terminal Block Suitable For 25 Sq Mm Conductor - 4 Nos. & Shorting Links On Din Channel L/C Providing And Fixing Din Channel Of Suitable Length, 6 Amp. Spmcb C Curve Characteristics, Earth Stud, Cable Support Clamp Suitable For Upto 4X25 Sqmm Cable. Logo/Name Of Manufacturer Shall Be Either Embossed Or Rivited Plate On The Pole. Galvanization As Per Relevant Is Code Etc As Required , Fabrication Supplyiing And Fixing B-Class Galvanised Single Overhang Arm Bracket Made Out Of 250 Mm Long Galvanized Top Tube With Cap 1000Mm Long 32 Mm Dia Galvanized Pipe With Tightening Bolts Complete As Reqd. , Fabrication Supplyiing And Fixing B-Class Galvanised Double Overhang Arm Bracket Made Out Of 250 Mm Long Galvanized Top Tube With Cap 1000Mm Long 32 Mm Dia Galvanized Pipe With Tightening Bolts Complete As Reqd. , Fabrication,Supplying,Installation,Testing,Commissioning Of 12 Mts.High Mast System With Its Accessories ,Mast Shaft Shall Be In One Section , Hot Dip Galvanized 4Mm Thick (Single Dip ) Inside And Out Sides And Suitable For Wind Velocity As Per Is 875 Part3 .There Shall Be In Longitudinal Seam Weld Per Section And No Circufrential Weld. It Should Also Included Accessories For High Mast Head Frame ,2 Point Suspension System With Steel Wire Rope 5Mm Dia. (7/19Construction) Single Drum Winch ,Galvanized Lantern Carriage Arrangement Suitable For 4/6 Nos. Flood Light Luminaries Luminaries Symmitrically And Its Control Gears Boxes And Lighting Finial ,The Mast Shall Have Integral Type Manual Tool Mounted At The Base Compartment Of Its Raising And Lowering Operation With Foundation Bolts And Anchor Plate And Control Panel Housing Suitable Reinforced Cement Concrete (1:2:4) Shallow Foundation Of Size 1M(L)X1m (W)X2m Deep I/C Excavation Of Earth I/C Excavation Of Earth, Providing Cutting, Bending And Placing In Position, Rewinforcement Of Cold Twisted Bars Of 12 Mm Dia -2100 Mm Long (Approx.) - 16 Nos.And Reinforcement Of Cold Twisted Bar Of 8 Mm Dia - 3700 Mm (Approx.) - 13 Nos. (With 150 Mm Spacing) As Required With Positioning Of 4 Nos Foundation Bolts And Providing Dwc Hdpe Pipe For Cable Entry & Exit As Required For High Mast Considering The Safe Soil Bearing Capacity At Site As 10T/Sqm At 2Mts. Depth With All Material I/C,4Nos S.P Mcb,63Amp.Dpisolator Etc As Reqd. Logo/Name Of Manufacturer Shall Be Embossed On The Pole. Galvanized As Per Relevant Is. , Supply And Fabrication Of Pole Protection System Made Up 8 Swg Steel Wire Mesh Of Size 25 Mm X 75 Mm Rectanglar With 50 Mm X50 Mmx6mm Ms Angle Iron For Supporting The Mesh I/C Mv Danger Plate And Grounding The Protection System In Suitable Quality Of cement concrete Etc. , Providing And Fiving Name Board Made Of Ms Sheet 90X60cm, 1Mm Thick With Frame Of Ms Angle 50X50x6mm, Two Diagonal Braces At The Back Of The Sheet Of Ms Flat 40X6mm, Total Height Of The Board Above Ground Level 2.40M, Length Of Legs Below Ground 0.30M Embedded In Cement Concrete Block 1:2:4 (1 Cement: 2 Coarse Sand: 4 Graded Stone Aggregate 20Mm Nominal Size) 30X30x45cm Including Excavation And Removal Of Surplus Earth With In 50M Lead, Applying Priming Coat Of Approved Steel Primer, Painting With Synthetic Enamel Paint Of Approved Quality And Lettering With Enamel Paint Of Approved Colour (One Side) As Per Drawing/Direction Of Engineer-In-Charge , Providing And Fixing Of Stainless Steel Name Plate Of Size 6X8 Sq Inch Made Of 20 Gauge Sheet Including Engraved Name Of Area Representative Duly Painted Along With Ss Clamp Nut Bolt Etc As Required. , Supply Of Xlpe Insulated,Pvc Sheathed Al.Conductor Armoured Cable 1.1Kv Grade Conforming To Is 7098/1988 Of Following Sizes (A) 2 X6 Sqmm , Supplying And Laying Of Following Size Dwc Hdpe Pipe Isi Marked Along With All Accessories Like Socket, Bend, Couplers Etc. Conforming To Is 14930, Part Ii Complete With Fitting And Cutting, Jointing Etc.Direct In Ground (75 Cm Below Ground Level) Including Excavation And Refilling The Trench But Excluding Sand Cushioning And Protective Covering Etc., Complete As Required. 63 Mm Dia (Od-63 Mm & Id-51 Mm Nominal) , Supplying And Laying Of Following Size Dwc Hdpe Pipe Isi Marked Along With All Accessories Like Socket, Bend, Couplers Etc. Conforming To Is 14930, Part Ii Complete With Fitting And Cutting, Jointing Etc. In The Existing Trench, Complete As Required. 63 Mm Dia (Od-63 Mm & Id-51 Mm Nominal) , Excavation Of The Cable Trenches In Hard Rock Not Exceeding 1.5 Metres In Width, And Lift Upto 1.5 Metres, Including Getting Outthe Excavated Soil And Disposal Of Excavated Soil As Directed Within A Lead Of 50 Metres , Providing And Laying In Position Cement Concrete Of Specific Grade Excluding The Cost Of Centering And Shuttering-All Work Up To Plinth Level:1:3:6 (1 Cement : 3 Coarse Sand (Zone-Iii) Derived From Natural Sources : 6 Graded Stone Aggregate 20 Mm Nominal Size Derived From Natural Sources. , Supplying And Fixing Of Light Class G.I. Pipe Of 50 Mm Dia. (Nominal) 3 Metres Length Along The Pole For Protection Of Under Ground Cable As Required. , Led Street Light Fixture, Powder Coated Pressure Die Cast Aluminum Body (System Lumen Efficacy 135 Lm/Watt) Supplying, Installation, Testing & Commissioning Of Street Light Led Fixture, Powder Coated Pressure Die Cast Aluminium Body With Built In Or Separate Driver As Per The Requirement With Driver Efficiency 85%, Input Voltage: 140-270 Volt Ac, Frequency 50/60 Hz, Operating Temp Range -5 0C To 50 0C, Internal Surge Protection Of 5 Kv L,N,E As Per Iec 61000-4-5, Driver Efficiency 85%,Thd 10% As Per Iec 61000-3-2, P. F.=0.95, Ip-66,Ik-10, Cri 70, Under Voltage And Over Voltage Protection, Emi-Emc As Per Cispr-15, Lenses For Beam Angle As Per Iesna Type I/Ii/Iii As Per The Width Of The Road And The Project Requirement., Suitable To Fit In Up To 65Mm Dia Pipe, Life Time (Led,Driver & Electrical Circuitary) Of Minimum 50000 Burning Hours With 70% Of Initial Lumen Maintained Till Life Ends As Per Lm80 Extrapolation Ies Tm-21-11 Report, Cct 3000°K / 4000°K / 5700°K /6500°K (As Per Ansi Bin), Sdcm(Standard Deviation Color Matching) 5, Maximum Power Consumption Should Not More Than The Specified Rating And Fixture Shall Be Of Relevant Bis Standard Complete In All 51 Delhi Schedule Of Rates (E&M)-2025 Respect I/C External Connections With 1.5 Sq Mm Frls/Hffr, Pvc Insulated Copper Conductor Single Core Cable And Earthing Etc. As Required With Minimum 5 Year Oem Warranty. System Lumen Efficacy 135 Lm/Watt Output . Lm79 & Lm80 Test Report And All Testing Required For Led Fixtures As Per Bis Shall Be Submitted.. Shape Size And Cct Shall Be As Approved By Engineer-In-Charge As Per Requirement. (Thermal Management: Heat Sink Of Aluminium Housing Such That Led Junction Temperature Shall Not Rise Above 90°C). 45 Watt , Led Flood Light, Powder Coated Pressure Die Cast Aluminium (System Lumen Efficacy 135 Lm/Watt) Supplying, Installation, Testing & Commissioning Of Flood Light, Powder Coated Pressure Die Cast Aluminium Body With Built In Or Separate Driver As Per The Requirement With Driver Efficiency 85%, Input Voltage: Input Voltage: 140-270 Volt Ac, Frequency 50/60 Hz, Operating Temp Range -5 0C To 50 0C, Internal Surge Protection Of 5 Kv L,N,E As Per Iec 61000-4-5, Driver Efficiency 85%,Thd 10% As Per Iec 61000-3-2, P. F.=0.95, Ip-66,Ik-10, Cri 70, Under Voltage And Over Voltage Protection, 54 Delhi Schedule Of Rates (E&M)-2025 Emi-Emc As Per Cispr-15, Lenses For Beam Angle 30 Deg-120Deg As Per The Application And The Project Requirement., Suitable Tilt Able Fitting, Life Time (Led, Driver & Electrical Circuitry) Of Minimum 50000 Burning Hours With 70% Of Initial Lumen Maintained Till Life Ends As Per Lm80 Extrapolation Ies Tm-21-11 Report, Cct 3000°K / 4000°K / 5700°K /6500°K (As Per Ansi Bin) , Sdcm (Standard Deviation Colour Matching) 5, Maximum Power Consumption Should Not More Than The Specified Rating And Fixture Shall Be Of Relevant Bis Standard Complete In All Respect I/C External Connections With 1.5 Sq.Mm Frls/Hffr, Pvc Insulated Copper Conductor Single Core Cable And Earthing Etc. As Required With Minimum 5 Year Oem Warranty. System Lumen Efficacy 135 Lm/Watt Output. Lm79 & Lm80 Test Report And All Testing Required For Led Fixtures As Per Bis Shall Be Submitted. Shape Size And Cct Shall Be As Approved By Engineer-In-Charge As Per Requirement. (Thermal Management: Heat Sink Of Aluminium Housing Such That Led Junction Temperature Shall Not Rise Above 90°C). 100W
|
