|
Soldering Kit: Tin-Lead Solder 60/40 (Diameter 1.0 Mm) No Less Than 200 G, Soldering Flux (Gel) No Less Than 50 G, Rosin No Less Than 50 G, Braid For Removing Solder No Less Than 1 Pc. (Length 1.5 M), Replaceable Soldering Tips At Least 2 Pcs., Tip Cleaner (Heat-Resistant Sponge) At Least 1 Pc., Mounting Tweezers At Least 1 Pc., Soldering Holder (Mini-Third Hand Or Board Clamp) At Least 1 Pc. Goods Must Meet Or Exceed The Standards Specified In The Technical Specification. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Act Until The Identified Deficiencies Are Completely Eliminated., Spare Parts Kit: Propellers - 4 Pcs., Frame - 1 Pc., Motors 4 Pcs. Propellers-4 Pcs, Frame-1 Pcs Motors 4 Pcs Propeller 15 3‑Blade: Diameter 15 Inches, Pitch 7, Number Of Blades 3, Material: Fiberglass-Composite, Weight 63.9G, Hub Diameter 220Mm, Hub Thickness 12Mm. Motor: Model 4214 380Kv, Rated Voltage 8S Lipo (30.4V), Operating Range 3-12S, Kv Value 380 R/V, Maximum Power 1312 W, Maximum Continuous Current 41 A, No-Load Current 1.45 A (At 10 V), Maximum Thrust Up To 4510 G (With 15X7 Or 13X10 Propellers At 8S), Internal Winding Resistance 42 Mohm, 12 Slot / 14 Pole Configuration (12N14p), Motor Dimensions 51.2 × 49 Mm, M4 Base Mount (30 × 30 Mm), Reinforced Frame, With Mounting Accessories Kit Material: T300 Carbon Fiber; Frame Type: 15-Inch (Quadcopter); 647 Mm; Propellers: 15; Frame Size: 517 × 517 Mm; Top Plate Thickness: 2.0 Mm; Side Panel Thickness: 2.0 Mm; Camera Installation Distance: 19 Mm; 30.5 Mm / 20 Mm; Flight Controller Compatibility: 30.5 Mm; Internal Frame Height: 25 Mm. 13-15″ Propellers Supported, 14 Awg Silicone Wiring 150 Mm Long, Motor Weight 195 G. The Supplier Agrees To Provide Product Samples (Parts/Components) For Pre-Assembly And Testing. The Customer Has The Right To Assemble And Check The Technical Characteristics Of Several Copies., Power Cable No Less Than 2×1.5 Mm² – 30 M, Power Cable No Less Than 2×0.75 Mm² – 10 M, Signal Cable No Less Than 4×0.5 Mm² – 12 M, Utp Cat5e Twisted Pair Cable No Less Than 10 M, Installation Wire No Less Than 0.5 Mm² – 15 M, Silicone Power Cable 14–16 Awg Not Less Than 10 M, Set Of Connectors And Terminals (Xt60, Jst.) - 1 Set. Goods Must Meet Or Exceed The Standards Specified In The Technical Specification. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Act Until The Identified Deficiencies Are Completely Eliminated., A Set Of Heat-Shrinkable Tubes Of At Least 4 1/0.5 Mm, 522 Piece Tubes (In Assortment): Diameter Of At Least 1.5–2 Mm - 500 Pcs. (Pieces Of 50–100 Mm), Diameter Of At Least 3–4 Mm – 400 Pcs. (Pieces), Diameter Of At Least 5–6 Mm - 300 Pcs. (Pieces), Diameter Of At Least 8–10 Mm - 200 Pcs. (Segments), Color Black/Red/Blue/Yellow (Assorted), Shrinkage Ratio 2:1, Intended For Insulating And Marking Wires And Connections. Goods Must Meet Or Exceed The Standards Specified In The Technical Specification. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Act Until The Identified Deficiencies Are Completely Eliminated., Drone Test Bench Rigid Metal Frame Structure/Mounting Platform With Adjustable Clamps For 19″ Drone Frames, Material—Steel/Aluminum Alloy With Corrosion Coating, Stand Dimensions ~700×700×400 Mm (L×W×H) With The Ability To Change The Width/Height Of The Fixation; Weight ~8–15 Kg; Platform Tilt Angle Adjustment ±15…±30°; Universal Clamps/Clamps For Fastening The Frame (For Different Sizes), Anti-Vibration Rubber Pads/Shock Absorbers, Removable Support Platform/Footrests For The Drone, Holes For Mounting Sensors/Marking Marks, Mechanical Scales/Rulers For Centering The Frame; The Design Is Resistant To Mechanical Loads And Vibration During Static Tests, Without Power Supply, Without Sensors, Without Measuring Modules, Without Electronics; Contents: Base Frame, Mounting Clips/Clamps, Manual Adjustment Bolts, Rubber Gaskets, Installation Instructions., Thermo Adhesive Sticks (Eva): Diameter 7 Mm, At Least 12 Pcs. (Length 100–200 Mm, Assorted), Diameter 11 Mm, At Least 8 Pcs. (Length 100–300 Mm, Assorted), Melting Point Not Less Than 150–200 °C. Goods Must Meet Or Exceed The Standards Specified In The Technical Specification. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Act Until The Identified Deficiencies Are Completely Eliminated., 0M X 0.15Mm X 8Mm For Spot Welding And Soldering Of Batteries - High Quality Material Designed For Connecting Battery Cells In Batteries, Assembling Lithium-Ion (Li-Ion), Lithium Polymer (Li-Po) And Other Battery Packs. Goods Must Meet Or Exceed The Standards Specified In The Technical Specification. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Act Until The Identified Deficiencies Are Completely Eliminated., Epoxy Resin No Less Than 5 Kg, Hardener (Included With The Resin Or Separately) No Less Than 2.5 Kg, Reinforcing Fabric (Fiberglass) No Less Than 10 M², Plastic Measuring Containers No Less Than 5 Pcs., Paint Brushes No Less Than 10 Pcs., Protective Gloves (Nitrile/Latex) No Less Than 10 Pairs. Goods Must Meet Or Exceed The Standards Specified In The Technical Specification. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Act Until The Identified Deficiencies Are Completely Eliminated.
|
