Annual Repair, Shifting, Installation & Maintenance And Restoring Of Pump Of (1) Jaganpura, (2) Ramkrishna N ... in India

Work Detail

Annual Repair, Shifting, Installation & Maintenance And Restoring Of Pump Of (1) Jaganpura, (2) Ramkrishna Nagar, (3) Nandlal Chapra And (4) Srinagar Colony Tdps Under Mech. Works Division, Buidco, Patna For The Period Of Done Before Monsoon 2026 (01St June 2026 To 15Th Oct 2026).-5 Cost for supply and fitting of bronze bush of size ID 80MM OD 95MM length 210mm 1 job 0.00 6 Cost for supplying and fitting of rubber patta with bolts & nuts for 10" dia. Motor pump couplings. 1 set 0.00 7 Cost for supplying and fitting of ball bearing SKF 7317 BEP of DE including CP & labour cess. 2 nos 0.00 8 Cost for supplying and fitting of roller ball bearing SKF of NDE NU2219ECJ or ECP including CP & labour cess. 1 no. 0.00 9 Cost for rubber insertion 1/8” thick. 10 kg 0.00 10 Cost for making steel key for impeller and coupling pulley. 2 nos 0.00 11 Cost for supplying and fitting SS316 lock nut for bearing as per sample. 1 no. 0.00 12 Cost for supplying and fitting SS316 lock washer. 1 no. 0.00 13 Cost for supplying and fitting nose type CI dom nut of nose type for impeller as per sample. 1 no. 0.00 14 Cost for fitting consumable materials such as grease 2 kg, gland packing 5/8”- 5 kg, cotton waste, packing paper, rubber water thrower etc as required at the time of fitting of pump. 1 job. 0.00 15 Cost for reassembling of pump shaft, its bearing and accessories into the bearing housing and fitting of impeller in workshop. 1 job. 0.00 16 Cost for supplying all labours, tools & tackles at site for fitting of bearing housing along with impeller with pump casing and tightening all holding bolts and nuts of pump casing, checking alignment of pump bearing housing,palcing of motor on base, doing coupling of motor with pump, checking and correcting alignment of motor pump and doing all electrical connection of motor & testing on no-load and full load. etc all complete.(1job x 2 days) 2 job. 0.00 17 Cost for transportation of pump and its accessories from pump house to firm workshop and back to pump house (The total weight of pump and accessories is approximately 600 kg & work shall be undertaken by loading on Pick-up Van). 1 job. 0.00 18 Cost for supplying and fitting bolts and nuts of different sizes with washer. 6 Kg 0.00 19 Deduct : Cost of Scrap materials bronze. 3 kg 0.00 Total- 0.00 There are 2 nos of 100 HP C/F pumps 2 nos 0.00 0.00 Annexure -2 Name of work - Annual repairing and servicing of 150 HP CF pump of storm drainage pumping plant . Sl. No Particulars Quantity Rate Amount(Rs) 1 Cost for providing all labours, tools and tackles at site for opening all coupling bolts of 150 HP CF motor and pump and all the electrical connections of motor, taking down motor from its base by top lifting of motor from motor base and stacking the motor at proper place. 1 job 0.00 2 Cost for providing all labours, tools and tackles at site for opening of all bolts and nuts of pump casing and bearing housing & taking out of bearing housing together with impeller and coupling and pump shaft (complete rotating assembly). 1 job 0.00 3 Cost for opening and dismantling 150 HP pump rotating assembly in workshop and tacking out impeller, pump shaft and bearings from bearing housing, thrust collar, grease shield of DE & NDE, shaft sleeve, spacer sleeve, bearing cover, etc, and cleaning all inner components for ready for repair. 1 job 0.00 4 Cost for re-metaling, turning and polishing of SS 410 pump shaft and rethreading two points & straightening the shaft by hydraulic pressure machine. 1 job 0.00 5 Cost for supply and fitting of Bronze bush of size OD 102MM ID 90MM Length 152mm 1 Nos. 0.00 6 Cost for supplying and fitting of roller ball bearing SKF 3219 A of driving end including CP & labour cess. 2 nos 0.00 7 Cost for supplying and fitting of roller ball bearing SKF FAG 7315 BMP UO of non driving end including CP & labour cess. 1 nos 0.00 8 Cost for rubber insertion 1/8” thick. 8 kg 0.00 9 Cost for making steel key for impeller and coupling pulley. 2 nos 0.00 10 Cost for making, supplying and fitting impeller lock screw made of SS 316 with full thread. 1 Set 0.00 11 Cost for making, supplying and fitting impeller lock washer made of SS 316 with full thread. 1 Set 0.00 12 Cost for supplying and fitting lock nut for bearing. 1 no 0.00 13 Cost for supplying and fitting lock washer. 1 nos 0.00 14 Cost for fitting consumable materials such as grease 2 kg, gland packing 5/8”- 5 kg, cotton waste, packing paper, rubber water thrower etc as required at the time of fitting of pump. 1 job. 0.00 15 Cost for reassembling of pump shaft, its bearing and accessories into the bearing housing and fitting of impeller in workshop. 1 job. 0.00 16 Cost for supplying all labours, tools & tackles at site for fitting of bearing housing along with impeller with pump casing and tightening all holding bolts and nuts of pump casing, checking alignment of pump bearing housing, and palcing of motor on base, doing coupling of motor with pump, checking and correcting alignment of motor pump and doing all electrical connection of motor & testing on no-load and full load.etc all complete.(1 job X 2 days) 2 job. 0.00 17 Cost for transportation of pump and its accessories from pump house to firm workshop and back to pump house (The total weight of pump and accessories is approximately 800 kg & work shall be undertaken by loading on Pick-up Van). 1 job. 0.00 19 Cost for supplying and fitting bolts and nuts of different sizes with washer. 6 Kg 0.00 20 Deduct : Cost of Scrap materials Stainless steel 4 Kg 0.00 Total 0.00 Annexure -3 Name of work - Aannual repairing and servicing of 156 HP CF pump of 156 HP diesel engine pump . Sl. No. Particulars Qty. Unit Rate Amount (Rs.) 1 Cost for providing all labours, tools and tackles at site for opening all coupling bolts of 156 HP CF motor and pump and all the electrical connections of motor, taking down motor, from its base by top lifting of motor from motor base and stacking the motor at proper place. 1 job 0.00 2 Cost for providing all labours, tools and tackles at site for opening of all bolts and nuts of pump casing and bearing housing & taking out of bearing housing together with impeller and coupling and pump shaft (complete rotating assembly). 1 job 0.00 3 Cost for opening and dismantling 156 HP pump rotating assembly in workshop and tacking out impeller, pump shaft and bearings from bearing housing, thrust collar, grease shield of DE & NDE, shaft sleeve, spacer sleeve, bearing cover, etc, and cleaning all inner components for ready for repair. 1 job 0.00 4 Cost for re-metaling, turning and polishing of SS 410 pump shaft and rethreading two points & straightening the shaft by hydraulic pressure machine. 1 job 0.00 5 Cost for supply and fitting of Bronze bush of size 102mm OD X 90mm ID X 150 mm long 1 Nos. 0.00 6 Cost for supplying and fitting of roller ball bearing SKF 22320 E of driving end including CP & labour cess. 2 nos 0.00 7 Cost for rubber insertion 1/8” thick. 8 kg 0.00 8 Cost for making steel key for impeller and coupling pulley. 2 nos 0.00 9 Cost for making, supplying and fitting impeller lock screw made of SS 316 with full thread. 1 Set 0.00 10 Cost for making, supplying and fitting impeller lock washer made of SS 316 with full thread. 1 Set 0.00 11 Cost for supplying and fitting lock nut for bearing. 1 no 0.00 12 Cost for supplying and fitting lock washer. 1 nos 0.00 13 Cost for fitting consumable materials such as grease 2 kg, gland packing 5/8”- 5 kg, cotton waste, packing paper, rubber water thrower etc as required at the time of fitting of pump. 1 job. 0.00 14 Cost for reassembling of pump shaft, its bearing and accessories into the bearing housing and fitting of impeller in workshop. 1 job. 0.00 15 Cost for supplying all labours, tools & tackles at site for fitting of bearing housing along with impeller with pump casing and tightening all holding bolts and nuts of pump casing, checking alignment of pump bearing housing, etc all complete. 1 job. 0.00 16 Cost for transportation of pump and its accessories from R K Avanue pump house to firm workshop and back to pump house (The total weight of pump and accessories is approximately 800 kg & work shall be undertaken by loading on Pick-up Van). 1 job. 0.00 17 Cost for placing of motor on base, doing coupling of motor with pump, checking and correcting alignment of motor pump and doing all electrical connection of motor & testing on no-load and full load. 1 job. 0.00 18 Cost for supplying and fitting bolts and nuts of different sizes with washer. 6 Kg 0.00 19 Cost for supplying and fitting SS coupling bolt as per sizes and sample. 12 nos 0.00 20 Cost for supplying and fitting Damroo shape rubber coupling bush. 12 nos 0.00 21 Deduct : Cost of Scrap materials Stainless steel 3 Kg 0.00 TOTAL 0.00 Annexure-4 Name of work - Annual repairing and servicing of 177 HP submersible pump set of storm drainage pumping plant . Sl. No Particulars Quantity Rate Amount(Rs) 1 Cost for providing all labours, tools and tackles at site for disconnecting the 177 HP submersible pump set and taking out from sump well. 2 P/job 0.00 2 Cost for dismantaling of monoblock dubmersible pump set taking out rotor from startor of motor and taking out damaged bearing from rotor and cleaning with petrol and ready for rapair work. 2 P/job 0.00 3 Cost for supplying and fitting Angular Contact ball bearing no. 3313A/C3 SKF Make. 2 each 0.00 4 Cost for supplying and fitting deep grooved ball bearing no. 6313 ZZ3 SKF Make. 2 Each 0.00 5 Cost for supplying and fitting copper cable socket. 8 each 0.00 6 Cost for supplying and fitting cable entry kit. 2 P/set 0.00 7 Cost for supplying and fitting joint rubber gasket. 2 each 0.00 8 Cost for making, supplying and fitting mechanical lock. 2 P/set 0.00 9 Cost for supplying and fitting mechanical seal as per size and sample. 2 each 0.00 10 Cost for supplying following with GST @ 18%, CP @ 10 % and lanour cess @ 1% (i) Mobil (Super Servo-10) hydrolic 10 P/ltr. 0.00 (ii) Servo bearing grease 5 p/kg 0.00 (iii) Nuts, bolts and key of different sizes 2 P/set 0.00 11 Cost for fitting and bearing in rotor of motor assembling rotor in startor of motor complete set. 2 p/job 0.00 12 Cost for suppyling and fitting rubber insertion sheet of sizes 1/8" thick (black). 6 p/kg 0.00 13 Cost for transportation of pump motor assembly from site to workshop for repair and back to pump house after repair including all cost of labour for loading and unloading. 2 p/job 0.00 14 Cost for providing all labours, tools and tackles at site for lowering of motor pump assembly. Fitting and fixing of sump motor assembly to discharge pipe and testing on load. 2 p/job 0.00 Total 0.00 Annexure - 5 Name of Work : - Annual servicing of 156 HP diesel engine and its accessories vacuum pump set of storm drainage pumping plant . Sl. No Particulars Quantity Rate Amount(Rs) 1 Cost for providing all labours, tools, tackles and an experienced mechanic at site for servicing of 156 HP diesel engine of Greaves make by checking of fuel pump, oil pump, decarbonisation of engine cylinder head and testing of engine on unload and load, etc, all complete. 1 job. 0.00 2 Cost for supplying and fitting following :- (i) Air filter outer 1 set 0.00 (ii) Diesel filter 1.1 L 2 nos. 0.00 (iii)set of joints 1 set 0.00 (iv)Lubricating oil filter 1 set 0.00 (v)Set of Hoses 1 set 0.00 (vi)Hose pipe clip 1 no. 0.00 (vii) Flexible pipes 1 set 0.00 (viii) Pre Diesel Filter 'O' ring 1 no. 0.00 (ix) Fuel on Solenoid switch 24 V DC for fuel pump 1 no. 0.00 (x) Coolant 5 ltr cane 1 cane 0.00 (xi) Lube Oil 20 ltr 15 W 40 (25 LTR X 1 CANE) 1 cane 0.00 (xii) Open relay 1 no. 0.00 (xiii) Start Relay 1 no. 0.00 (xiv) V Belt 1 set 0.00 (xv) H P Pipe 1 set 0.00 (xvi) Exhaust pipe flexible 125 mm ID 1 no. 0.00 (xvii)Sealing washer 1 set 0.00 (xviii)Set of gasket 1 set 0.00 (xix)Cable Harmess 1 no. 0.00 3 Cost for checking of leakages in radiator in workshop and repairing of leakages in radiator by replacing damaged portion of copper tube and repairing leakages by soldering of reparable copper pipes. 1 Job. 0.00 4 Cost for supplying and fitting Tata Green Battery / Exide make of capacity 150 AH excluding the cost of old battery. 2 nos. 0.00 5 Cost repairing of electrical panel of diesel engine by repalcing all burnt and damaged electrical wires and fuses and ckecking the electrical panel including the cost of labour and electricians. 1 Job. 0.00 6 Cost for servicing of alternator 1 Job. 0.00 7 Cost for self servicing 1 job. 0.00 8 Cost for providing all labours, tools and tackles at site for opening and taking of self of 10 HP vacuum pump diesel engine for repairing and refitting the same after repairing. 1 job. 0.00 Total 0.00 Annexure-6 Name of work:- Repairing and servicing of 10 HP vaccum pump. Sl no Particulars Qty Rate Amount 1 Cost for providing all labour, tools and tackles at site for opening electrical connection of 10 HP vacuum pump motor, foundation bolts and nuts of pump, GI flange and taking out and removing it from base. 2 P/job. 0.00 2 Cost for dismantling of 10 HP vacuum pump for taking out impeller, pump shaft, etc and cleaning all the components for ready for repair. 2 P/job. 0.00 3 Cost for repairing of steel shaft by remetalling on cut point, turning and polishing of the shaft and making key way groove. 2 P/job. 0.00 4 Cost for repairing GM impeller by brazing the blades of impeller with brass, turning, polishing and facing the blade to bring it to running condition 2 P/job. 0.00 5 Cost for making supplying and fitting GM bush as per sample. 4 Each 0.00 6 Cost for supplying and fitting ball bearing no. 6307 ZNR of SKF. 4 Each 0.00 7 Cost for supplying and fitting oil seal as per sample. 4 Each 0.00 8 Cost for fitting materials such as packing paper, grease, gland packing, nuts and bolts, cotton waste etc required at the time of fitting of pump. 2 Each 0.00 9 Cost for repairing of body (brass discs) by facing both the sides. 2 Each 0.00 10 Cost for supplying and fitting split type GM gland flange. 2 Each 0.00 11 Cost for reassembling of pump with shaft, impeller, bearing set, oil seal, etc accessories in workshop. 2 Each 0.00 12 Cost for transportation of pump fromKrishnaghat Pump house to work shop and back to pump house. 2 P/job. 0.00 13 Cost for providing all labour, tools and tackles for reinstallation of motor and pump on base and doing electrical connections and testing all complete. 2 P/job. 0.00 14 Cost for supplying motor pump 3" dia. coupling pulley 2 Each 0.00 15 Cost for making hole as per dia. Of pump & motor shaft and making key way groove in the coupling on lathe machine and fitting & fixing in the pump & motor. 3 P/set 0.00 16 Cost for cutting and removing burnt cable sockets and doing cable socketing of 4 mm² 3 core copper cable of both motor and starter. 10 Each 0.00 17 Deduct : Cost of Scrap materials Gun metal -1 P/Kg 0.00 Total- 0.00 ANNEXURE- 7 Name of work - Annual repairing and servicing of transformer of 2x315 kva, 1x 500 KVA transformer and servicing, greasing, repairing of AB switch & DP structure of 11 KV electric sub - station . Sl. Particulars Quantity Rate Amount(Rs) 1 Cost for providing all labours, tools and tackles at site for opening and dismantling all electrical connections of HT and LT of transformer, loading and unloading the transformer on transportation vehicle by using hydraulic crane including the hire cost and reinstallation, commissioning after repairing at DPS 1 jobs. 0.00 2 Cost for opening the top cover and dismentling the same for taking out HT and LT coils from transformer body after draining out transformer oil and stacking in a container, taking out sludge of transformer oil and cleaning inside of transformer body and radiator fins by blowing pressurised oil. 1 jobs. 0.00 3 Cost for providing all labours and tools and taking out HT and LT coil from transformer body by using chain pulley block 1 jobs. 0.00 4 Cost for supplying and fitting following :- (i) LT stud of copper 3 nos. 0.00 (ii) LT bush 3 nos. 0.00 (iii) HT stud of copper 3 nos. 0.00 (iv) HT bush 3 nos. 0.00 (v) Rubberized gasket 1 nos. 0.00 5 Cost for supplying and filling of tranformer oil. 60 ltrs. 0.00 6 cost for transformer oil filtration 370 ltrs. 0.00 7 Cost for cutting and removing old and damaged cable socket of LT cable of transformer and doing cable socketing including the cost of 185 mm² cable socket and all requisite insulating materials such as glass tape, PVC tape, empire Tape, etc. 3 nos. 0.00 8 Cost for tightening of HT & LT studs after refilling of transformer oil and fitting of top cover with ruberised gasket and re-installing equalizing pipes, etc all complete work. 1 jobs. 0.00 9 Cost for providing all labours, tools and tackles at site for opening and dismantling of 400 Amp. AB switch such as male & female contact, knife type contact, cleaning & washing each component with petrol properly and resetting them all complete job. 1 jobs. 0.00 10 Cost for supplying & fitting following spares. :- i. Post insulator. 2 Pcs 0.00 ii. Horn gap fuse. ( 1 pcs = 3 nos.) 2 Pcs 0.00 iii. Net fuse for 400 Amp. AB switch. (1 pcs =3 nos.) 2 Pcs 0.00 iv. Copper wire 6 SWG. 2 kg 0.00 v. GI bolts & nuts with washer of different sizes 10 kg 0.00 vi. Knife type male & female contact for 400 Amp. AB switch. ( 1 Pcs = 3 nos) 1 Pcs 0.00 vii Lightening arrestor for 11 KV sub station 1 Pcs 0.00 viii Rabit conductor for connection of main ncoming feeder. 5 M 0.00 ix Fuse wire 19 no. 0.5 Kg 0.00 11 Cost for PVC sleeving suitable to withstand 11 KV power supply for sleeving of 6 SWG jumpher wire 5 Mtr. 0.00 13 Deduct : Cost of Scrap materials Copper 4 kg 0.00 Total Cost 0.00 Therefore cost for 3 (three) nos 0f Transformer 3 nos. 0.00 0.00 ANNEXURE-8 Name of Work : Annual repairing and servicing for starter of 3 x150 HP C/F pump set & 2 x 177 HP Submersible pump set and cable of storm drainage pumping plant . Sl. No particulars Qty Rate Amount 1 Cost for providing all labours, tools and tackles at site for servicing LT distribution panel board by decarbonisation of its all contact joints, bushes by washing with petrol doing proper insulation at cable terminals with requisite kinds of tapes and repair all internal wiring of above mention starters of pump sets. 5 P/job. 0.00 2 Cost for providing all labours, tools and tackles at site for servicing LT distribution panel board of pump set decarbonisation of its all contact joints, bushes by washing with petrol doing proper insulation at cable terminals with requisite kinds of tapes and repair its all internal wiring. 5 P/job. 0.00 3 Cost for supplying and fitting followings in the panel board of pump sets: - (i) Cost for supply of MCCB DN2-250D with thermal release range 200-250 A and breaking capacity 36 ka in the outgoing feeders of panel boards including all taxes, 1 Each 0.00 (iii) LED pilot lamp standard 12-240 V AC Colour R/Y/G/A 15 Each 0.00 (iv) Volt meter (0-500) volt. 1 Each 0.00 (v) Ampere meter (0-300) Amp. 1 Each 0.00 (vi) CT coil 300/5 2 Each 0.00 (vii) 1.5 sq. mm flexible copper wire for repair of internal wiring of all the panel boards & starters 1 P/coil 0.00 (viii) Making, supplying & fitting, fixing frames made of M.S. flats & angles for fixing of starters on the ground . 1 Each 0.00 (ix) Cost for supply of C - curve DP 32 Amp. MCB in the combine panel boards including all taxes, 2 Each 0.00 (x) Cost for supply of MCCB DH 125 with thermal release range 100-125 A and breaking capacity 35 ka in the outgoing feeders of panel boards including all taxes, 1 Each 0.00 4 Cost for supplying & fitting followings for starters :- (i) CT operated Over load relay CT5MC305ANA3C having relay range for pump set including all taxes, 1 P/job. 0.00 (ii) Contactor MCE 15 RN3.7 pump set including all taxes, 1 Each 0.00 (iii) Electronic timer 415V, 50Hz KRTPN10.0 for pump sets including all taxes, 1 Each 0.00 (iv) Contact set 6-288 of contactor MCE 15 RN3.7 for pump set including all taxes, 1 P/set 0.00 (v) Cost for supply of 12 M x 35 mm x 5 mm copper flat for making bus-bars for connections of cable with starters, ACB & MCCB. 1 P/job. 0.00 5 Cost for laying of 70 & 95 sq. mm cable inside pump house including supplying & fitting cable glands, etc, all complete job. 2 Each 0.00 6 Cost for doing cable socketing including the cost of 95 mm² cable socket and all requisite insulating materials such as glass tape, PVC tape, empire Tape, etc. 20 Each 0.00 7 Cost for supplying , fitting, repairing and servicing of soft starter of 2 x 177 HP sub pump sets are i. HRC Fuse - 06 nos. ii. MCCB 630 amp - 2 nos iii. TP contactor 220 volt control-01 no. iv.ON/OFF Switch- 02 nos v. soft starter control kit - 01 vi. Soft starter display kit board - 01 vii. soft starter display cable 29 p/38 p flat cable -01 viii.Relay meter ( control line) - 01, ix.Auto switch- 01,x. Relay meter (MPR) - 01 ,xi. single phase preventer- 01,xii. Four step self starting relay- 01,xiii. Amp volt control meter- 01, xiv.MCB- 04 way 63 amp - 01,xv. 63 amp single phase - 04 no. , xvi.2 amp - 6 no.xvii contractor model LC1E 1201, 4 pole 12 amp- 6 nos.xviii LED- 15 nos. xix 110 volt,LED - 06 nos, 440 volt 1 Each 0.00 8 Cost for doing cable socketing including the cost of 70 mm² cable socket and all requisite insulating materials such as glass tape, PVC tape, empire Tape, etc. 15 Each 0.00 9 Providing & Bus Duct cabling of 50 mm² x 3 core PVC insulated and PVC sheathed copper conductor flexible cable in double from starter to motor & laying in trench/ cable tray in pump house. (If required) 50 mts 0.00 10 Cost for supply of DOL starter for one no.. 10 HP motor including all taxes, duty & cess. 1 Each 0.00 11 Cost for cutting and removing burnt cable sockets and doing cable socketing of 4 mm² 3 core copper cable of both motor and starter. 6 Each 0.00 12 Deduct : Cost of Scrap materials copper -2 P/Kg 0.00 Total 0.00 Annexure-9 Name of work - Cleaning and desilting of sump of Drainage pumping stations under Mechanical works division, Buidco . Sl. No Particulars Quantity Rate "Amount (Rs)" 1 Labour Analysis for desilting BCD SOR 2.24.1 Labour required = 1.2 labour per Cum 2 Cost for supplying all labours, tools and suitable tackles for cleaning and desiliting of filled and choked sewage tank, approach channel and inlet chamber etc of drainege pumping station and to lift and disposal of all soils up to a lead of 50 mtr all complete as per specification and direction of E/I at site. (i) sump 14.5 m x 3.1 m x 2 m (avg) = 89.90 m³ 89.9 m³ 0.00 3 Cost for providing all labours, tools and tackles at site for repairing, removing rust,dust, scale, smokes etc. from old surface and spray painting two or more coats with anticorrosive bituminous paint of approved brand of two MS gate and channel. 1 job 0.00 4 Cost for providing all labours, tools, tackles & a 10 H.P. electric pump set for dewatering the area within band including cost of hire of electric pump set . SOR RCD PM6 1001. Basic rate-195/Hr. 30 Hr 0.00 Total 0.00 Gr-05 (2) Name of Work- Annual repairing, maintenance & operation of electro-mechanical accessorries of the pump sets installed in storm drainage pumping plant at Antaghat for monsoon 2026 for the year 2026-27. "Sl. No." Particulars of work Qty. Unit Rate Amount (in Rs.) 1 Cost for complete repairing and overhauling of 175 HP VT pump set no.-1 as per Annexure-1 1 Per job 0.00 0.00 2 Cost for complete repairing and overhauling of 175 HP VT pump set no.-2 as per Annexure-2 1 Per job 0.00 0.00 3 Cost for Repairing and overhauling of 2 nos electric motors by dismantaling the motors, double coat varnishing, heating, loop repairing, replacement of the damaged bearing, assembling with all required consumable materials and testing on load. 1 P/Job 0.00 4 Cost for repairing & servicing of panel boards and starter of 2X 175 HPVT pump set as per Annexure-3 1 Per job 0.00 0.00 5 Cost for cleaning, servicing, greasing and repairing of flap valve as per Annexure-4 . 1 Per job 0.00 0.00 6 Cost for servicing & filteration of T- oil of 2 x 500 KVA out door transformers as per Annexure-5 1 Per job 0.00 0.00 7 Cost for complete repairing and servicing of 198 HP diesel Engine as per Annexure-6 1 Per job 0.00 0.00 8 Complete repairing and overhauling of 198 HP pump set of diesel engine as per Annexure-10 1 Per job 0.00 0.00 9 Cost for servicing, cleaning, greasing and repairing of AB switch and DP structure of 11 KV electric substation as per Annexure-7 1 Per job 0.00 0.00 10 Cost for cleaning and Desilting of sumps as per Annexure-8 1 Per job 0.00 0.00 11 Cost for Providing & installation of New water level Gauge as per direction of Engineer-in-charge . 1 P/Job 0.00 12 Cost for Making Bamboo gratings of size 12'x12'-08 nos.(approx) made of 12' (approx) long 2.5'' dia bamboo with gap of 2.5'', with nails ans S.S. wire for fixing and installation in the sumps inlet at storm Drainage Pumping Plant, Antaghat as Per Annexure-9 1 P/Job 0.00 0.00 13 Cost for complete repair of Sluice gate as Per Direction of Engineer-in-Charge. 1 P/Job 0.00 14 Cost for Complete Reparing ,Overhauling ,Servicing & Functionlity of 10 Ton Manual Chain pulley block Over head crane mounted on DPS as Per Direction of Engineer-in-Charge. 1 P/Job 0.00 15 Cost for construction of 8 m deep earth station as per standard with connection of all electro mechanical equipment with recessing GI flat & GI wiire as per Direction in charge. 2 Per job 0.00 16 Cost for providing of spray painting over double coat of paint with red oxide primer of all existing electro-mechanical equipments by removing old paints as per direction of engineer in charge. 1 P/Job 0.00 17 Cost for light wiring in & out the pump house with all required electrical wiring. 1 Per job 0.00 18 Cost for Providing & Laying of 240 Sq.mm 3.5 core copper armoured Cable for 2x175 HP starter to motor with required Jointing kit as per Direction of Engineer -In Charge (make - KEI/Polycab/Havells). 30 per m 0.00 19 Cost for outdoor cable end terminations heat shrink type LT cable jointing kit suitable for 240 mm2 cable with providing gas cylinder kit etc. as per Direction of E/I 6 each 0.00 20 Cost for Deployment of 5 nos. x 3 shifts road sweepers for removing floating materials from sump, cleaning the premises, taking out the garbages from pump impeller and miscellaneous work during the monsoon period 1st june 2026 to 15th Oct 2026 and 02 no. x 1 shift from 16th Oct.2026 to 31.03. 2027 and 1st April' 26 to 31th May' 26. during rest period. ( The no. of road Sweeper may increase as per situation arisen due to heavy rain fall). 2511 each 0.00 21 Cost for Deployment of 2 nos. x 3 shifts Highly skilled technician cum pump operators during the monsoon period 1st june 2026 to 15th Oct. 2026 and 01 nos. x 3 shift from rest period (16.10.2026 to 31.03.2027) and 1st April' 26 to 31th May' 26. ( The no. of pump operators may increase as per situation arisen due to heavy rain fall). 1506 each 0.00 22 Cost of all required materials for making and fitting of anti flood sluice gate at out side of bypass gate etc as per direction of E/I. 1 Job 0.00 23 Providing all materials for construction of shed near inlet sump grattings (30x40) 1 job 0.00 24 Maintenance of miscllenious work of Electro-machineries for the period of (01.04.26 to31.03.27) at DPS. The Bidder shall be totally responsible for proper Functioning of DPS with immediate minor & major work repairing like burning of motor, transformer, maintenance of new supply pump & transformer per annum, panel, starter, bearing replacing, cleaning of Campus, Sprinking of Bleaching Powder, pump operation, Functionality of Sluice gate & any other equipments installed or to be install should be Functional in this DPS, Proper flood light, fan, rabber mat, Log Book, ABC store press (4 kg-02nos) & carbon dioxide (4kg-02nos) type fire extingusher required for safety purpose, spray Painting, misc.type of all civil releted work, light wiring, exhaust fan, Name Plate of buidco, wall painting, warvet wire Recharge of CCTV, availability of 24 hrsx365 days in sufficient quantity of saftey materials, black stone (ballast) transportation and loading, unloadingof any equipment/material, repairing of Civil structure during emergency for water draining as per Direction of E/I. 1 Per job 0.00 Total 0.00 ANNEXURE-01 "Sl. No." Particulars of Works Qty. Unit Rate Amount (in Rs.) 1 Cost for providing labour, tools and tackles at site for opening all coupling bolts of 175HP VT motor and pump and all the electrical connections of motor, taking down motor from its base by top lifting of motor from motor stool and stacking the motor at proper place. 1 p/job 0.00 2 Cost for providing all labours, tools and tackles at site for opening and taking out discharge tee, column pipe, bowl mouth assembly, etc of 175 HP VT pump from sump. 1 p/job 0.00 3 Cost for opening and dismantling of bowl mouth assembly of 175 HP VT pump, taking out pump shaft, upper & lower bowl mouth, impeller, upper and lower bushes, etc in workshop with GST, CP & Labour cess. 1 p/job 0.00 4 Cost for checking of pump shaft, head shaft & line shaft on lathe for straightness and straightening the same on hydraulic press machine with GST, CP & Labour cess. 2 each 0.00 5 Cost for remetalling & rethreading at both ends of pump & line shaft with GST, CP & Labour cess. 3 each 0.00 6 Cost for making and supplying line shaft bronze bush of size ID 56 mm OD 65 mm Length 125 mm 2 each 0.00 7 Cost for making and supplying stuffing box bronze bush of size ID 56 mm OD 65 mm Length 100 mm 1 each 0.00 8 Cost for making and fitting of SS 416 shaft coupling by cutting and making internal thread of size ID 53 mm OD 76 mm Length 145 mm 2 each 0.00 9 Cost for making and supplying lower bearing bush for discharge bowl of size ID 69 mm OD 82 mm Length 130 mm 1 p/job 0.00 10 Cost for making and supplying upper discharge bowl bearing bush of size ID 69 mm OD 145 mm Length 130 mm 1 p/job 0.00 11 Cost for making M.S. check nut as per sample and size with GST, CP & Labour cess. 1 each 0.00 12 Cost for making, supplying and fitting SS 316 Key as per sample and size for impeller and coupling with GST, CP & Labour cess. 3 each 0.00 13 Cost for making, supplying and fitting steel coupling bolts as per size and sample with GST, CP & Labour cess. 8 each 0.00 14 Cost for repairing of ratchet plate by doing CI welding, grinding & finishing and making 11 nos. sharp edges of proper size and sample by grinding machine with GST, CP & Labour cess. 1 p/job 0.00 15 Cost for reassembling of pump accessories such as bowl mouth bush, impeller, pump shaft, etc in bowl housing in the work shop with GST, CP & Labour cess. 1 p/job 0.00 16 Cost for transportation of pump and its accessories from Antaghat pump house to workshop and back to pump house including all cost of labour charge for loading & unloading with GST, CP & Labour cess. 1 p/job 0.00 17 Cost for scratching old paint of column pipe and discharge pipe and doing one coat primer with red oxide and painting two coats with black Japan paint with GST, CP & Labour cess. 1 p/job 0.00 18 Cost for supplying and fitting MS bolts & nuts with washer of different sizes with GST, CP & Labour cess. 14 p/kg 0.00 19 Cost for supplying and fitting rubber insertion sheet of size 1/8" thick (black) with GST, CP & Labour cess. 20 p/kg 0.00 20 Cost for fitting materials such as greese- 5 kg, cotton waste - 4 kg, gland packing -3 kg, emery paper- 10 sheets, K oil - 7 ltrs. etc required at the time of fitting of pump with GST, CP & Labour cess. 1 p/job 0.00 21 Cost for supplying and filling mobil with GST, CP & Labour cess. 12 P/Ltr 0.00 22 Cost for fitting of pump accessories and lowering such as column pipe, bowl mouth assembly, discharge tee line shaft, all spider bushes, etc into the sump. 1 p/job 0.00 23 Cost for placing of motor on its base, doing coupling of motor & pump, doing all electric connection of motor and testing the pump on load. 1 p/job 0.00 24 Cost for supplying of 'O' ring of different sizes made of neoprine rubber as per sample with GST, CP & Labour cess. 8 each 0.00 25 Cost for supplying of OIL SEAL of sizes 65-95-13 made of nitrile rubber with GST, CP & Labour cess. 2 each 0.00 26 Cost for supplying of rachet pin with GST, CP & Labour cess. 4 each 0.00 27 Cost for deep groove ball bearing 6024 of SKF with GST, CP & Labour cess. 1 Each 0.00 28 Deduct : Cost of Scrap materials Bronze. -16 p/kg 0.00 29 Deduct : Cost of Scrap materials Stainless steel -22 p/kg 0.00 Total 0.00 ANNEXURE-02 "Sl. No." Particulars of Works Qty. Unit Rate Amount (in Rs.) 1 Cost for providing labour, tools and tackles at site for opening all coupling bolts of 175HP VT motor and pump and all the electrical connections of motor, taking down motor from its base by top lifting of motor from motor stool and stacking the motor at proper place. 1 p/job 0.00 2 Cost for providing all labours, tools and tackles at site for opening and taking out discharge tee, column pipe, bowl mouth assembly, etc of 175 HP VT pump from sump 1 p/job 0.00 3 Cost for opening and dismantling of bowl mouth assembly of 175 HP VT pump, taking out pump shaft, upper & lower bowl mouth, impeller, upper and lower bushes, etc in workshop with GST, CP & Labour cess. 1 p/job 0.00 4 Cost for checking of pump shaft, head shaft & line shaft on lathe for straightness and straightening the same on hydraulic press machine with GST, CP & Labour cess. 3 each 0.00 5 Cost for remetalling & rethreading at both ends of pump & line shaft with GST, CP & Labour cess. 4 each 0.00 6 Cost for making and supplying line shaft bronze bush of size ID 56 mm OD 65 mm Length 125 mm 2 each 0.00 7 Cost for making and supplying stuffing box bronze bush of size ID 56 mm OD 65 mm Length 100 mm 1 each 0.00 8 Cost for making and fitting of SS 416 shaft coupling by cutting and making internal thread of size ID 53 mm OD 76 mm Length 145 mm 2 each 0.00 9 Cost for making and supplying lower bearing bush for discharge bowl of size ID 69 mm OD 82 mm Length 130 mm 1 p/job 0.00 10 Cost for making and supplying upper discharge bowl bearing bush of size ID 69 mm OD 145 mm Length 130 mm 1 p/job 0.00 11 Cost for making M.S. check nut as per sample and size with GST, CP & Labour cess. 1 each 0.00 12 Cost for making, supplying and fitting SS 316 Key as per sample and size for impeller and coupling with GST, CP & Labour cess. 2 each 0.00 13 Cost for making, supplying and fitting steel coupling bolts as per size and sample with GST, CP & Labour cess. 10 each 0.00 14 Cost for repairing of ratchet plate by doing CI welding, grinding & finishing and making 11 nos. sharp edges of proper size and sample by grinding machine with GST, CP & Labour cess. 1 p/job 0.00 15 Cost for reassembling of pump accessories such as bowl mouth bush, impeller, pump shaft, etc in bowl housing in the work shop with GST, CP & Labour cess. 1 p/job 0.00 16 Cost for transportation of pump and its accessories from Antaghat pump house to workshop and back to pump house including all cost of labour charge for loading & unloading with GST, CP & Labour cess. 1 p/job 0.00 17 Cost for scratching old paint of column pipe and discharge pipe and doing one coat primer with red oxide and painting two coats with black Japan paint with GST, CP & Labour cess. 1 p/job 0.00 18 Cost for supplying and fitting MS bolts & nuts with washer of different sizes with GST, CP & Labour cess. 12 p/kg 0.00 19 Cost for supplying and fitting rubber insertion sheet of size 1/8" thick (black) with GST, CP & Labour cess. 23 p/kg 0.00 20 Cost for fitting materials such as greese- 4 kg, cotton waste - 6 kg, gland packing - 2 kg, emery paper- 10 sheets, K oil -6 ltrs. etc required at the time of fitting of pump with GST, CP & Labour cess. 1 p/job 0.00 21 Cost for supplying and filling mobil with GST, CP & Labour cess. 10 P/Ltr 0.00 22 Cost for fitting of pump accessories and lowering such as column pipe, bowl mouth assembly, discharge tee line shaft, all spider bushes, etc into the sump. 1 p/job 0.00 23 Cost for placing of motor on its base, doing coupling of motor & pump, doing all electric connection of motor and testing the pump on load. 1 p/job 0.00 24 Cost for supplying of 'O' ring of different sizes made of neoprine rubber as per sample with GST, CP & Labour cess. 9 each 0.00 25 Cost for supplying of OIL SEAL of sizes 65-95-13 made of nitrile rubber with GST, CP & Labour cess. 2 each 0.00 26 Cost for supplying of rachet pin with GST, CP & Labour cess. 4 each 0.00 27 Cost for roller bearing 29322 E of SKF with GST, CP & Labour cess. 1 Each 0.00 28 Cost for deep groove ball bearing 6024 of SKF with GST, CP & Labour cess. 1 Each 0.00 29 Deduct : Cost of Scrap materials Bronze. -12 p/kg 0.00 30 Deduct : Cost of Scrap materials Stainless steel. -20 p/kg 0.00 Total 0.00 ANNEXURE-03 "Sl. No." Particulars of Works Qty. Unit Rate Amount (in Rs.) 1 Cost for providing all labours, tools & tackles at site for opening & dismantling all internal wiring, copper bus bars of 2 x 175 HP pump set panel board, removing dust, vermins and foreign materials by blowing machine, cleaning and washing all the internal joints & components with petrol and greasing them properly and resetting, all complete job with GST, CP & Labour cess. 1 P/job. 0.00 2 Cost for providing all labours, tools, suitable tackles and an electrician for opening and dismantling of 1000 Amp. ACB of 2x175 HP pump set, cleaning all the moving & fixed contacts with petrol and greasing them properly as well as setting the male & female contacts and replacing burnt bakelite terminals, all complete job with GST, CP & Labour cess. 1 P/job. 0.00 3 Cost for supplying and fitting following in the 175 HP pump set panel with GST, CP & Labour cess. : (i) CT coil 500/5 4 Each 0.00 (ii) Cost for supply of 2.5 sq. mm flexible copper wire for repair of internal wiring of all the panel boards & starters. 1 P/coil 0.00 (iii) LED pilot lamp standard 12-240 V AC Colour R/Y/G/A 5 Each 0.00 (iv) 3Ph VAF + PF, Class 1, 1A 2 Each 0.00 (v) Push Button ON / OFF Switch 2 Each 0.00 (vi) Cost for supply and fitting of 3 Pole, 415 v, 50 Hz DTH 800 MCCB having current rating 630 Amp. & breaking capacity 50 KA including GST, C.P. & Labour cess in the outgoing feeder of panel board of 175 HP pump set-1 . Make - L&T 1 Each 0.00 (vii) Cost for supplying, making & fitting 9 nos.. copper bus barsfrom copper flats of size 40 mm x 5 mm x 4.5 m long in the incomming & outgoing feeders of 2 nos. MCCB & 1 no. ACB. 1 P/job. 0.00 (viii) Cost for supply of lock with key for 2 x 175 HP panel boards and starters. 4 P/set 0.00 4 Cost for supplying and fitting followings in the soft starter of 175 HP pump sets are i. HRC Fuse - 06 nos. ii. MCCB 1000 amp - 2 nos iii. TP contactor 220 volt control-01 no. iv.ON/OFF Switch- 02 nos v. soft starter control kit - 01 vi. Soft starter display kit board - 01 vii. soft starter display cable 29 p/38 p flat cable -01 viii.Relay meter ( control line) - 01, ix.Auto switch- 01,x. Relay meter (MPR) - 01 ,xi. single phase preventer- 01,xii. Four step self starting relay- 01,xiii. Amp volt control meter- 01, xiv.MCB- 04 way 63 amp - 01,xv. 63 amp single phase - 04 no. , xvi.2 amp - 6 no.xvii contractor model LC1E 1201, 4 pole 12 amp- 6 nos.xviii LED- 15 nos. xix 110 volt,LED - 06 nos, 440 volt 2 P/job 0.00 5 Cost for complete repairing and changing of spare parts of APFC panel ( 7% reactor) are 200 KVAR- 01 no , TP 50 KA 800 amp MCCB- 1 no , C.T coil - 600/5 amp - 03 no. MCB 32 amp(TP) - 3 no. Wire 2.5 sq. mm - 01 coil, Power controller - 01 no. , Rotary handle - 01 no, speader - 01 set etc for proper controlling of power factor and also preventing power losses from transformer. 1 P/job 0.00 6 Cost for providing all labours, tools suitable tackles & electrician for opening and dismantling the starters of 2 x 175 HP pump sets by opening and dismantling all the contactors, timer, overload relay, etc, cleaning the starter by blowing air to remove dust & vermins, washing all the components with petrol, resetting the starter by replacing burnt & damaged contactors and their accessories, tapping all the bus bars by rapping pvc tape including the cost of pvc tape , petrol etc. all complete job with GST, CP & Labour cess. 2 P/job 0.00 7 Cost for supply of followings for starers of 2 x 175 HP pump sets with GST, CP & Labour cess. :- (i) Contactor LC1FDP185A. Make - C&S . 1 Each 0.00 (ii) Contactor LC1FDP265A . Make-C&S . 2 Each 0.00 (iii) Thermal overload relay with relay setting range 250-400 Amp. LR1F400. Make -C&S. 2 Each 0.00 (iv) Timer TA2-DS2 (0-30 SEC). Make - C&S. 2 Each 0.00 (v) AC coil of LC1FDP265A. Contactors. 2 Each 0.00 (vi) Brass bolts & nuts with washer of different sizes 5 P/kg 0.00 8 Cost for cutting and removing old and damaged Copper & aluminium cable socket of panel board & starters and doing cable socketing of 240 mm² cable of panel & starters including the cost socket and required insulating materials with GST, CP & Labour cess. 20 Each 0.00 9 Deduct : Cost of Scrap materials Copper -3 P/Kg 0.00 Total 0.00 ANNEXURE-04 "Sl. No." Particulars of Works Qty. Unit Rate Amount (in Rs.) 1 Cost for providing all labours tools and tackles at site for opening and dismantling of lifting gear unit mechanisms, cleaning with K. oil, greasing all the gears and resetting the same including all consumable materials such as K. oil, grease, cotton waste, mobil, etc and replacing all the bolts and nuts of TVS make with GST, CP & Labour cess. 2 Each 0.00 2 Cost for supplying all labours, tools and tackles at site for taking out damaged and broken wire rope of size 5/8" dia. and supplying and fitting new wire rope with GST, CP & Labour cess. 25 P/M 0.00 3 Cost for supplying and fitting 'U' clamp suitable for fastening 5/8" dia. wire rope with GST, CP & Labour cess. 6 Each 0.00 4 Cost for supplying all labours, tools and tackles at site for lifting plate of flap valves from outlet and supplying and fitting 3/4" x 8" long steel pin shaft in flap valve with GST, CP & Labour cess. 2 Each 0.00 5 Cost for dismentling and Repairing of damaged lifting unit mechnism including cost of gear unit etc with GST, CP & Labour cess. 2 P/job. 0.00 6 Cost for miscellaneous work such as closing leakages in flap valves caused due to floating materials in the valves with the help of diver before starting of pumping machineries during flood situation in Ganga river with GST, CP & Labour cess. 1 P/job. 0.00 7 Deduct : Cost of Scrap materials M.S. -5 P/Kg 0.00 Total 0.00 ANNEXURE-05 "Sl. No." Particulars of Works Qty. Unit Rate Amount (in Rs.) 1 Cost for providing all labours, tools and tackles at site for opening and dismantling all electrical connections of HT and LT of 500 KVA transformer with GST, CP & Labour cess. 1 P/job 0.00 2 Cost for opening the top cover and other equalizing pipes of transformer for fitting and tightening of HT & LT studs and draining of transformer oil and stacking of transformer oil in container with GST, CP & Labour cess. 1 P/job 0.00 3 Cost for supplying and fitting following with GST, CP & Labour cess. :- (i) LT stud of copper 3 Each 0.00 (ii) LT bush 3 Each 0.00 (iii) HT stud of copper 3 Each 0.00 (iv) HT bush 3 Each 0.00 (v) Rubberized gaskit 1 Each 0.00 (vi) Transformer oil 120 P/ltr. 0.00 4 Cost for tightening of HT & LT studs, refilling of transformer oil and fitting of top cover with ruberised gaskit and reisnstaling equalizing pipes, etc all complete work with GST, CP & Labour cess. 1 P/job 0.00 5 Cost for filtration of transformer oil with GST, CP & Labour cess. 500 P/ltr. 0.00 6 Cost for PVC sleeving suitable to withstand 11 KV power supply for sleeving of 6 SWG jumpher wire with GST, CP & Labour cess. 10 p/mtr 0.00 7 Cost for supplying making and fitting of 4 nos. extension bus bars each of length 1.25' made of copper strips of size 60 mm x 8 mm x 1.5 M for connection of cables to the transformers. 1 P/job 0.00 8 Cost for cutting and removing old and damaged cable socket of LT cable of transformer and doing cable socketing including the cost of 185 mm² cable socket and all requisite insulating materials such as glass tape, PVC tape, empire Tape, etc with GST, CP & Labour cess. 15 Each 0.00 9 Deduct : Cost of Scrap materials Copper -5 P/kg 0.00 Total 0.00 ANNEXURE-06 "Sl. No." Particulars of Works Qty. Unit Rate Amount (in Rs.) 1 Cost for providing all labours, tools, tackles and an experienced mechanic at site for servicing of 198 HP diesel engine of Greaves make by checking of fuel pump, oil pump, decarboration of engine cylinder head and testing of engine on unload and load etc all complete with GST, CP & Labour Cess. 1 P/job 0.00 2 Cost for supplying and fitting following with GST, CP & Labour cess. :- (i) Air Filter 1 Each 0.00 (ii) Diesel Filter set 1 p/set 0.00 (iii) Lubricating oil filter 2 Each 0.00 (iv) Set of Hoses 1 P/set 0.00 (v) Fuel Flexible pipe 1 p/set 0.00 (vi) Fuse 24 V Assly 1 Each 0.00 (vii) Coolant 5 ltr cane 1 p/cane 0.00 (viii) V Belt 1280 3 Each 0.00 (ix) Realy in electrical panel 2 Each 0.00 (x) Solenoid 24 Volt 1 Each 0.00 (xi) Lube Oil 20 Ltr 1 p/cane 0.00 (xii) Head Gasket 1 Each 0.00 (xiii) Set of joint 1 Each 0.00 (xiv) Set of sealing ring 1 P/set 0.00 (xv) Set of Hose clip 1 Each 0.00 (xvi) Magnetic Pickup 1 P/set 0.00 (xvii) Battery Terminal 4 Each 0.00 4 Cost for checking of leakages in radiator in workshop and repairing of leakages in radiatory by replacing damaged portion of cooper tube and repairing leakages by soldering of reparable cooper pipes with GST, CP & Labour cess. 1 P/job 0.00 5 Cost repairing of electrical panel of desel engine by replacing all burnt and damaged electrical wires and fuses and checking the electrical panel including the cost of labour and electicians with GST, CP & Labour cess. 1 p/job 0.00 6 Cost for repairing and servicing of self starter with all materials with GST, CP & Labour cess. 1 p/job 0.00 7 Cost for a alternator repairing & servicing with GST, CP & Labour cess. 1 P/job 0.00 Total 0.00 ANNEXURE-07 "Sl. No." Particulars of Works Qty. Unit Rate Amount (in Rs.) 1 Cost for providing all labours, tools and tackles at site for opening and dismantling of AB switch such as male & female contact, knife type contact, cleaning & washing each component with petrol properly and resetting them all complete job with GST, CP & Labour cess. 1 P/job 0.00 2 Cost for supplying & fitting following spares with GST, CP & Labour cess. :- i. Post insulator. 3 Each 0.00 ii. Horn gap fuse set. 3 Each 0.00 iii. Net fuse. 3 Each 0.00 iv. Fuse wire 19 SWG. 2 P/kg 0.00 v. Rabit conductor for connection of main incoming feeder. 20 P/ M 0.00 vi. Copper wire 6 SWG. 4 P/kg 0.00 vi. GI bolts & nuts with washer of different sizes 4 P/kg 0.00 vii. Knife type male & female contact for 400 Amp. AB switch. ( 1 Pcs = 3 nos) 1 Each 0.00 Total 0.00 ANNEXURE-08 "Sl. No." Particulars of Works Qty. Unit Rate Amount (in Rs.) 1 Cost for supplying all labours, tools and suitable tackles for cleaning and desiliting of filled and choked sump tank, approach channel and inlet chamber etc of different pumping station and to lift and disposal of all soils and foreign materials all complete as per specification and direction of E/I at site. (i) Sump – 3 nos x 4 m x 2.75 m x 1.25 m (avg) = 41.25 m³ (ii) Approach Chamber – (3.6 m + 10 m)/ 2 x 10 m x 0.75 m = 51 m³ (iii) Inlet Chamber- 3 nos. x 4.1 m x 2.75 m x 1 m (avg) = 33.83 m³ 126.08 p/m³ 0.00 2 Supplying all labours, tools and tackles for cleaning and extracting floating materials from the approach channel and bye pass drain outlet channel etc. (i) Approach Chamber – (3.6 m + 10 m)/ 2 x 10 m = 68 m² (ii) Inlet Chamber- 3 nos. x 4.1 m x 2.75 m = 33.83 m³ (iii) By Pass Drain- 15 m x 3.5 m = 52.50 m² (iv) Sump- 3 nos x 4 m x 2.75 m = 33 m² 187.33 P/m² 0.00 3 Cost for providing all materials , tools for making diversion bandh near bye pass drain with help of sand filled Plastic bags and placing the sand in proper stake and making water tight to divert the flow of water for desilting etc all complete as per direction of E.I. in Antaghat pumping plant . 1 x 3.7 m x 1.5 m x 1.8 m = 9.99 m³ @ 30 nos bag/m³ 9.99 x 30 = 300 bags 300 p/bag 0.00 4 Labour charge for taking out sand bags from drain of sump after desilting of bandh after the completion of desilting work in Antaghat pumping plant. 300 p/bag 0.00 5 Cost for providing all labours, tools, tackles & a 5 H.P. Diesel pump set at Antaghat pumping plant for dewatering the area within band including cost of hire of diesel pump set and lubricants & fuel. 12 p/hr 0.00 6 Cost for supplying all labour, tools, tackles at site for lift and disposal of soils and foreign materials to a lead of 15 KM all complete with loading and unloading charge all complete. (70% of silt taken out) 88.26 p/m³ 0.00 Total 0.00 ANNEXURE-09 "Sl. No." Particulars of Works Qty. Unit Rate Amount (in Rs.) 1 Cost for making and supplying bamboo gratings of size 12" long made of half 12' long x 2.5" dia. Bamboo having gaps of 2.5" between two consecutive bamboos including labours, tools and tackles. 8 Each 0.00 2 Cost for M.S wires for fastening of bamboo gratings into sump 9 p/kg 0.00 3 Cost for providing all labours, tools and tackles at site for fitting, fixing and binding bamboo gratings into sump. 9 Each 0.00 Total 0.00 ANNEXURE-10 "Sl. No." Particulars of work Unit Qty. Rate Amount 1 Cost for providing all labours, tools and tackles at site for opening all coupling bolts of 198 HP pump from motor and all electrical connection of motor and opening all nut and bolt of pump casing, bearing housing and taking out of bearing housing together with impeller coupling and pump shaft. P/job 1 0.00 2 Cost for dismentalling of all nut & bolt of pump casing, pump with pump shaft, bearing housing from pump casing including all labour, tools & tackles etc. P/job 1 0.00 3 Cost for remetalling, turning and polishing of SS 410 pump shaft and rethreading two points & straightening the shaft by hydraulic pressure machine including all labours, tools & tackles etc. P/job 1 0.00 4 Cost for making, supply and fitting of bronze nush including cutting. Turning, polishing and finishing of size 100 mm ID x 122 mm OD x 220 mm Length Each 1 0.00 5 Cost for supply and fitting of S cylindercal roller bearing no. SKF 3322 A equivalent for 198 HP pump with GST, CP and Labour Cess. Each 2 0.00 6 Cost for supply and fitting of spherical Roller bearing no. SKF 3322 a equivalent for 198 HP Electric pump with GST,CP & labour cess etc Each 1 0.00 7 Cost for making, supplying and fitting impeller steel key, lock screw and lock washer made of SS 316 with full thread. p/set 1 0.00 8 Repairing of impeller by gas welding at damaged portion, turning, polishing, finishing including supplying all labour, tools and tackles, welding machine hiring, electrode and all consumable items (if required) as per direction of E/I. p/job 1 0.00 9 Cost for supplying and fitting of mechanical seal, oil seal, 'O' rings, water deflector, lantern ring, hexa nut for gland packing, oil filler plug including labour, tools and tackles etc. p/job 1 0.00 10 Cost for supplying and fitting lock nut and lock washer for bearing including labour, tools and tackles. p/set 1 0.00 11 Cost for fitting consumable materials such as grease, gland packing 5/8", cotton waste, packing paper, flexible rubber water thrower etc as required at the time of fitting of pump. p/job 1 0.00 12 Cost for supplying al labours, tools & tackles at size for reassembling of bearing housing along with impeller with pump casing and tightening all holding bolts and nuts of pump casing, checking alignment of pump bearing housing on unload. P/job 1 0.00 13 Providing all labours, tools, tackles for installation of 198 HP pump on foundation,refitting nut-bolt & testing on unload at DPS. P/job 1 0.00 14 Cost for supplying and fitting bolts and nuts of different sizes with washer including labours, tools & tackles. P/kg 10 0.00 15 Cost for supplying and fitting SS coupling bolt as per size and sample including labours, tools & tackles Each 10 0.00 16 Deduct: Cost of scrap materials stainless steel P/kg -2 0.00 Total 0.00 Gr-05 (3) Name of Work- Annual repairing and servicing of electro mechanical equipment of drainage pumping plant of Kadamkuan before monsoon 2026 for the year 2026-27. SI.No. Description Of Work Qty Unit Rate (RS.) Amount (RS.) 1 Pump -75 HP C/F no-1,2 & 3, three phase,440 volts, 50 HZ. Annexture-1 1 Job 0.00 0.00 2 Motor- 75 HP C/F no- 1,2 &3 , three phase,440 volts, 50 HZ. Annexture-2 1 Job 0.00 0.00 3 Vaccum pump-3 x 10 HP three phase,440 volts, 50 HZ. Annexture-3 1 Job 0.00 0.00 4 Tranformer- 200 KVA Annexture-4 1 Job 0.00 0.00 5 Pump- 38 HP diesel engine pump . Annexture-5 1 Job 0.00 0.00 6 Starter cum panel- 2 x 75 HP .Annexture-6 1 Job 0.00 0.00 7 Desilting of sump Annexture-7 1 Job 0.00 0.00 8 Deployment of 2x3 nos. shift per day road sweepers for removing floating materials from sump, cleaning the premises, taking out the garbages from pump impeller and miscellaneous work during the monsoon period 01.06.2026 to 15.10.2026 and after mansoon (1x1) shift from 16 Oct 2026 to 31.03.2027 & 1st April 2026 to 31st May 2026 during rest period. (The no. of road sweepers may increase as per situation arisen due to heavy rain fall). 1050 shift 0.00 9 Deployment of per day shift wise (2X3) manpower for pump operation & Electricity work during the monsoon period 01.06.2026 to 15.10.2026 and after mansoon (1x3) shift from 16 Oct 2026 to 31.03.2027 & 1st April 2026 to 31st May 2026 during rest period.(The no. of pump operators may increase as per situation arisen due to heavy rain fall). 1506 shift 0.00 10 Operation & maintenance of the electro-machanical equipment for one year period and after the bidder shall be totally responsible for the operation of minor and major work of DPS i.e burning of motor, transformer, panel, starter, bearing, Shaft replacing, and any other fault etc. no further claim will be paid by Buidco. 1 Job 0.00 11 Spray painting of all electro mechanical equipment and pipe line over one coat of red primer complrte job. 1 Job 0.00 12 Cost for miscellaneous work such as CCTV camera, light, wiring, switch , switch board , medical kit, cable and other works in sewerage pumping plant Kadamkuan before monsoon . 1 Job 0.00 Total 0.00 Annexture-1 Name of work - Repairing and servicing of 3 X 75 HP CF pump of storm drainage pumping plant of Kadamkuan. Sl. No Particulars Quantity Rate Amount(Rs) 1 Cost for providing labour, tools and tackles at site for opening all coupling bolts of 75 HP CF motor and pump and all the electrical connections of motor, taking down motor from its base by top lifting of motor from motor base and stacking the motor at proper place with GST, CP & Labour Cess. 3 job 0.00 2 Cost for providing all labours, tools and tackles at site for opening of all bolts and nuts of pump casing and bearing housing & taking out of bearing housing together with impeller and coupling and pump shaft (complete rotating assembly) including all taxes, duties, Cess & CP. 3 job 0.00 3 Cost for opening and dismantling 75 HP pump rotating assembly in workshop and tacking out impeller, pump shaft and bearings from bearing housing, thrust collar, grease shield of DE & NDE, shaft sleeve, bearing cover, etc, and cleaning all inner components for ready for repairing including all taxes, duties, Cess & C.P. 3 job 0.00 4 Cost for supplying and fitting of angular contact ball bearing SKF Make 3213 A.for NDE 3 no. 0.00 5 Cost for supplying and fitting angular contact ball bearing SKF Make 3313 A/C3.for DE 3 no. 0.00 6 Cost for re-metaling, turning and polishing of SS 410 pump shaft and rethreading two points & straightening the shaft by hydraulic pressure machine including all taxes, duties, Cess & C.P. 3 job 0.00 7 Cost for making , supplying and fitting of bronze bush of size OD 65mm x 58mm x180mm. 3 nos 0.00 8 Cost for supply of Fenaflex type coupling of through bore type F120 size for pump no. 1 of 75 HP capacity including all taxes, duties, Cess & C.P. 3 job 0.00 9 Cost for turning and finishing the bore of coupling as per dia. Of pump shaft and motor shaft including cutting the key way as per size. Including all taxes, duties, Cess & C.P. 3 job 0.00 10 Cost for making, supplying and fitting of CI bearing bush as per sample and size including all taxes, duties, Cess & C.P. 3 set 0.00 11 Cost for rubber insertion 1/8” thick including all taxes, duties, Cess & C.P. 3 kg 0.00 12 Cost for fitting materials such as grease 2 kg, gland packing 5/8”- 3 kg, cotton waste, packing paper, rubber water thrower etc as required at the time of fitting of pump including all taxes, duties, Cess & C.P. 3 job. 0.00 13 Cost for reassembling of pump shaft, its bearing and accessories into the bearing housing and fitting of impeller in workshop including all taxes, duties, Cess & C.P. 3 job. 0.00 14 Cost for supplying all labours, tools & tackles at site for fitting of bearing housing along with impeller, placing of motor on its base by top lifting, coupling of motor with pump, checking of alignment of pump with motor,doing all electrical connection of motor & testing on no-load and full load including all taxes, duties, Cess & C.P. 3 job. 0.00 15 Cost for transportation of pump and its accessories from Kadamkuan pump house to firm workshop and back to pump house (The total weight of pump and accessories is approximately 500 kg & work shall be undertaken by loading on Pick-up Van) including all taxes, duties, Cess & C.P. 3 job. 0.00 16 Cost for supplying and fitting bolts and nuts of different sizes with washer including all taxes, duties, Cess & C.P. 14 Kg 0.00 17 Deduct : Cost of Scrap materials bronze metal 3 Kg 0.00 Total 0.00 Annexture-2 Name of work - Repairing and Servicing of 3x75 HP C/F motor No. 1, 2 & 3 of storm drinage pumping plant of Kadamkuan . Sl. No Particulars Quantity Rate Amount(Rs) 1 Cost for providing all labours, tools & tackles at site for opening and tackles at site for opening all electrical connections of 75 HP C/F motor and dismantalling of delievery line,suction line and taken out of motor by lifting of motor. 3 Job. 0.00 2 Cost for complete opening of 75 HP C/F motor part by part and taking out rotor from starter from servicing with GST, CP & Labour Cess. 3 Job. 0.00 3 Cost for taken out of top & bottom bearing from bearing housing with providing all labours, tools and tackles with GST, CP & Labour Cess. 3 Job. 0.00 4 Cost for providing all labours, tools & tackles for repairing of bearing housing with weilding with C.I. electrode turning and finishing as required shape and size with GST, CP & Labour Cess. 3 Job. 0.00 5 Cost for greasing the bearing of the motor and varnisihing, heating & tapping of enamelled copper winding wire including required materials like 3 kg grease and varnish- 7 ltrs with GST, CP & Labour Cess. 3 Job. 0.00 6 Cost for reassembling the rotor and stator of motor and also fitting of bearings in the bearing housing at repairing place with GST, CP & Labour Cess. 3 Job. 0.00 7 Cost for supplying and fitting bolts & nuts of different size with washer with GST, CP & Labour Cess. 6 Kg 0.00 8 Cost for rubber insertion 1/8" thick with GST, CP & Labour Cess. 4 Kg 0.00 9 Cost for providing all labours, tools & tackles at site for installation of 75 HP C/F motor on foundation base, doing all electric connection, refitting nut-bolts to the pump and base foundation also adjoining suction line, delivery pipe line, then testing on full load. 2 Job. 0.00 Total 0.00 Annexture-3 Name of work - Opening, dismantling and repairing of 3 x 10 HP vacuum pump of storm drainage pumping plant Kadamkuan . Sl. No Particulars Quantity Rate Amount (Rs) 1 Cost for providing all labour, tools and tackles at site for opening electrical connection of 10 HP vacuum pump motor, foundation bolts and nuts of pump, GI flange and taking out and removing it from base with GST, CP & Labour Cess. 3 jobs. 0.00 2 Cost for dismantling of 10 HP vacuum pump for taking out impeller, pump shaft, etc and cleaning all the components for ready for repair with GST, CP & Labour Cess. 3 jobs. 0.00 3 Cost for repairing of steel shaft by remetalling on cut point, turning and polishing of the shaft and making key way groove with GST, CP & Labour Cess. 3 jobs. 0.00 4 Cost for repairing GM impeller by brazing the blades of impeller with brass, turning, polishing and facing the blade to bring it to running condition with GST, CP & Labour Cess. 3 jobs. 0.00 5 Cost for making supplying and fitting GM bush as per sample with GST, CP & Labour Cess. 2 nos. 0.00 6 Cost for supplying and fitting ball bearing no. 6307 ZNR of SKF. 6 nos. 0.00 7 Cost for supplying and fitting oil seal as per sample with GST, CP & Labour Cess. 6 nos. 0.00 8 Cost for fitting materials such as packing paper, grease, gland packing, nuts and bolts, cotton waste etc required at the time of fitting of pump with GST, CP & Labour Cess. 3 jobs. 0.00 9 Cost for supplying and fitting split type GM gland flange with GST, CP & Labour Cess. 3 nos. 0.00 10 Cost for reassembling of pump with shaft, impeller, bearing set, oil seal, etc accessories in work shop with GST, CP & Labour Cess. 3 jobs. 0.00 11 Cost for transportation of pump from Kadamkuan Pump house to work shop and back to pump house with GST, CP & Labour Cess. 3 jobs. 0.00 12 Cost for providing all labour, tools and tackles for reinstallation of motor and pump on base and doing electrical connections and testing all complete with GST, CP & Labour Cess. 3 jobs. 0.00 13 Cost for cutting and removing burnt cable sockets and doing cable socketing of 4 mm² 3 core copper cable of both motor and starter with GST, CP & Labour Cess. 18 nos. 0.00 14 Deduct : Cost of Scrap materials Gun metal 1 Kg 0.00 Total 0.00 Annexture-4 Name of work - Servicing, cleaning, greasing and repairing of AB switch & DP structure of 11 KV electric sub - station & filtration of transformer oil of 1 x 200 KVA transformer, repairing, servicing of panel board etc of fully automatic star-delta starter of 3 nos. x 75 HP pump sets of sewerage pumping plant Kadamkuan. Sl. No Particulars Quantity Rate Amount(Rs) 1 Cost for providing all labours, tools and tackles at site for opening and dismantling of AB switch such as male & female contact, knife type contact, cleaning & washing each component with petrol properly and resetting them all complete job with GST, CP & Labour Cess. 1 jobs. 0.00 2 Cost for supplying & fitting following spares with GST, CP & Labour Cess. :- i. Post insulator. 2 nos. 0.00 ii. Horn gap fuse. 2 nos. 0.00 iii. Net fuse for 400 amp AB switch (1 pc = 3 nos.) 2 nos. 0.00 iv. Copper wire 6 SWG. 2 kg 0.00 v. GI bolts & nuts with washer of different sizes 1.5 kg 0.00 vi. Knife type male & female contact for 400 amp AB sitch (1 pcs =3 nos) 1 nos. 0.00 vii. Rabit conductor for connection of main incomming feeder. 5 mtr 0.00 viii. Fuse wire 19 no. 0.5 kg 0.00 3 Cost for providing all labours, tools and tackles at site for opening and dismantling all electrical connections of HT and LT of 200 KVA transformer, loading and unloading the transformer on transportation vehicle by using hydraulic crane including the hire cost and reinstallation, commissioning after repairing at DPS. 1 jobs. 0.00 4 Cost for opening the top cover and dismentling the same for taking out HT and LT coils from transformer body after draining out transformer oil and stacking in a container, taking out sludge of transformer oil and cleaning inside of transformer body and radiator fins by blowing pressurised oil. 1 jobs. 0.00 5 Cost for supplying and fitting following with GST, CP & Labour Cess. :- (i) LT stud of copper 2 nos. 0.00 (ii) LT bush 2 nos. 0.00 (iii) HT stud of copper 2 nos. 0.00 (iv) HT bush 2 nos. 0.00 (v) Rubberized gaskit 1 nos. 0.00 6 Cost for tightening of HT & LT studs, refilling of transformer oil and fitting of top cover with ruberised gaskit and reisnstaling equalizing pipes etc all complete work with GST, CP & Labour Cess. 1 jobs. 0.00 7 Cost for filtration of transformer oil with GST, CP & Labour Cess. 150 ltrs. 0.00 8 Cost for PVC sleeving suitable to withstand 11 KV power supply for sleeving of 6 SWG jumpher wire with GST, CP & Labour Cess. 5 mtr 0.00 9 Cost for cutting and removing old and damaged cable socket of LT cable of transformer and doing cable socketing including the cost of 185 mm² cable socket and all requisite insulating materials such as glass tape, PVC tape, empire Tape, etc. with GST, CP & Labour Cess. 2 nos. 0.00 10 Cost for providing all labours and tools & Taking out HT & LT coil from Transformer body by using chainfully block 1 jobs. 0.00 11 Cost for supplying & filling of Transformer oil. 150 ltrs. 0.00 12 Deduct : Cost of Scrap materials Copper 4 kg 0.00 Total 0.00 Annexture-5 Name of work - Repairng and servicing of 38 HP diesel pump set of storm drainage pumping plant Kadamkuan . Sl. No Particulars Quantity Rate Amount (Rs) 1 Cost for providing all labours, tools, tackles and an experienced mechanic at site for servicing of 38 HP. Eicher make diesel engine by checking of fuel pump, oil pump, decarbonisation of engine cylinder head and testing of engine on unload and load etc. all complete with GST, CP & Labour Cess. 1 Job. 0.00 2 Cost for supplying and filling mobil (castrol make) with GST, CP & Labour Cess. 10 ltrs. 0.00 3 Cost for supplying and fitting following with GST, CP & Labour Cess. :- (i) Mobil filter. 1 no. 0.00 (ii)Diesel filter. 2 no. 0.00 (iii) Air filter. 1 no. 0.00 (iv) V Belt 1 no. 0.00 4 Cost for complete overhuling of self starter by changing the bearing, carbon brush, bushes nut-bolts, washer etc. as requried during overhauling. 1 Job. 0.00 5 Cost for supplying and fitting battery terminal wires of length 2 mtr. Each. 2 no. 0.00 6 Cost for banzo bolts and washer with GST, CP & Labour Cess. 12 nos. 0.00 7 Cost for supplying and fitting battery cable and terminals with GST, CP & Labour Cess. 2 nos. 0.00 8 Cost for supplying all labour and tools for servicing and repairing of self starter of Diesel engine including changing of it's spares such as bearings, carbon brush, penion, bushes etc and testing on load at site with GST, CP & Labour Cess. 1 Job. 0.00 9 Cost for repair of alternator by changing it's burnt armature, carbon brush, bearings, bushes,etc as required and testing on load at site with GST, CP & Labour Cess. 1 Job. 0.00 Total 0.00 ANNEXURE- 6 Name of work - Repairing of 3 x 75 HP FASD air break Starter cum control panel for operation of DPS Kadamkuan . SI.No Particular Quantity Rate Amount(Rs) 1 Providing all Labours,tool & tackles for repairing of 1 x 75 HP, 1 x 100 HP and 1 x 125 HP fully automatic star-delta air break starter cum panel with supply,changing and fitting contactor, timer, over load realy unit, push botton and changing all internal wiring with suitable PVC Wire & strip as required. (i) Contactor 70 amp BCH make for 75 HP pump.for 2 sets. 4 no. 0.00 (ii) Timer (0-30)sec. 2 no. 0.00 (iii) Thermal Over load relay unit having (84-135) Amp. 3 no. 0.00 (iv) Push Button. 4 no. 0.00 (v) C.T Coil 1000/5 . 6 no. 0.00 (vi) MCB . 6 no. 0.00 (vii) Single phase preventer. 3 no. 0.00 (viii) Ammeter (0-200) amp. 3 no. 0.00 (ix) Voltmeter(0-500)Volt . 3 no. 0.00 (x) selector switch . 3 no. 0.00 (xi) Bus-bar . 6 no. 0.00 (xii) Phase indicating lamp . 6 no. 0.00 2 Cost for supplying and fitting single core 70 mm² copper wire for lead wire. 10 M 0.00 Total Rs. 0.00 Annexture- 7 Name of work - Cleaning and desilting of sump, bye pass gate, approach channel, outlet channel etc of pirmuhani Drainage pumping stations under Mechanical works division, Buidco , Patna Sl. No Particulars Quantity Rate "Amount (Rs)" 1 Labour Analysis for desilting BCD SOR 2.24.1 Labour required = 1.2 labour per Cum 2 Cost for supplying all labours, tools and suitable tackles for cleaning and desiliting of filled and choked circular sewage tank, approach channel and inlet chamber etc of Kadamkuan drainege pumping station and to lift and disposal of all soils up to a lead of 50 mtr all complete as per specification and direction of E/I at site. (i) Sump- 3.5 mx 22.75 m x 2 m = 19.25 m³ 19.25 m³ 0.00 3 Cost for providing all labours, tools and tackles at site for repairing, removing rust,dust, scale, smokes etc. from old surface and spray painting two or more coats with anticorrosive bituminous paint of approved brand of two MS gate and channel . 1 job 0.00 Total 0.00 Gr-05 (4) Name of Work- Annual repairing , servicing , operation and maintenance of all electro-mechanical equipment of the pumps set installed in drainage IPS pumping plant at Pirmuhani under south Bihar , works division Buidco, patna before monsoon 2026 for the year 2026-27. SI.No. Description Of Work Qty Unit Rate (RS.) Amount (RS.) 1 pump no-1 -20 HP submersible pump (Annexure-1) 1 Job 0.00 0.00 2 20 HP submersible motor . (Annexure-2) 1 Job 0.00 0.00 3 Pump no-2 & 3 :- 60 HP Submersible (Annexure-4) 2 Job 0.00 0.00 4 60 HP Submersible motor. (Annexure-5) 2 Job 0.00 0.00 5 Starter & control panel . (Annexure-3) 1 Job 0.00 0.00 6 Transformer 315 KVA (Annexure-6) 1 Job 0.00 0.00 7 Desilting of sump (Annexure-7) 1 Job 0.00 0.00 8 Repairing & providing of light wiring , fan, inside & outside with supply of required LED Bulb ,wired etc complete job for proper light. 1 job 0.00 9 Complete the below mention mix work as per instruction of Engineer-In-Charge. a Writing the name details of officers & pump operator, sweeper on the wall paint. 1 Job 0.00 b Providing log book & other required Register. 4 Job 0.00 c Providing & availability during monsoon period in sufficient qty required safety materials like first aid box kit, machinery work hand tool kit, electrical glooves, normal hand gloves, torch (02 no.), umbrella (02), safety jacket, gun boot, rain coat & other required as per instruction of Engineer-In-Charge. 1 Job 0.00 10 Operation & maintenance of the electro-machineries for monsoon period and after (01.04.2026 to 31.03.2027) the bidder shall be totally responsible for the operation of minor and major work of IPS i.e burning of motor, panel, starter, bearing/Shaft replacing, CCTV camera etc. no further claim will be paid by Buidco. 1 job 0.00 11 Deployment of 2x3 nos. shift per day road sweepers for removing floating materials from sump, cleaning the premises, taking out the garbages from pump impeller and miscellaneous work during the monsoon period 01.06.2026 to 15.10.2026 and after mansoon (1x1) shift from 16 Oct 2026 to 31.03.2027 & 1st April 2026 to 31st May 2026 during rest period. (The no. of road sweepers may increase as per situation arisen due to heavy rain fall). 1050 staff 0.00 12 Deployment of per day shift wise (2X3) manpower for pump operation & Electricity work during the monsoon period 01.06.2026 to 15.10.2026 and after mansoon (1x3) shift from 16 Oct 2026 to 31.03.2027 & 1st April 2026 to 31st May 2026 during rest period.(The no. of pump operators may increase as per situation arisen due to heavy rain fall). 1506 staff 0.00 13 Providing all materials for construction of shed near inlet sump grattings (25x30) 1 job 0.00 Total 0.00 Annexure-1 "Name of work - Repairing of 20 HP submersible motor of pump set at Pirmuhani I & D plant . " SI. NO Particulars Quantity Rate Amount (RS) 1 Cost for Providing all labours,tools and tackles at site for disconnecting the 20 HP submersible pump set and taking out form sump well. 1 Job 0.00 2 Cost for dismantaling of monoblock Sub-mersible pump set,taking out rotor from stator of motor and taking out damaged bearing from rotor and cleaning with petrol and ready for repair work. 1 Job 0.00 3 "Cost for supplying and fitting Angular contact ball bearing no. 3313A/C3.SKF make. " 1 no. 0.00 4 "Cost for supplying and fitting deep grooved ball bearing no. 6313 ZZ.Skf make. " 1 no. 0.00 5 Cost for supplying and fitting copper cable socket. 6 nos. 0.00 6 Cost for supplying and fitting joint rubber gasket. 1 no. 0.00 7 Cost for making, supplying and fitting mechanical lock . 1 set 0.00 8 Cost for supplying and fitting mechanical seal as per size and sample. 1 no. 0.00 9 Cost for supplying following . (i) Mobil (super servo-10) hydraulic 5 ltrs 0.00 (ii) Servo bearing grease 2 Kgs 0.00 (iii) Nuts,bolts and key of different sizes. 1 set 0.00 10 Cost for supplying and fitting rubber insertion sheet of size 1/8'' thick(black). 4 Kgs 0.00 11 Cost for transportation of pump motor assembly form site to workshop for repair and back to pump house after repair including all cost of labour for loading and unloding. 1 Job 0.00 12 Cost for providing all labours,tools and tackles at site for lowering of motor pump assembly . Fitting and fixing of pump motor assembly to discharge pipe and testing on load. 1 Job 0.00 TOTAL 0.00 Annexture -2 Name of work - Repairing and servicing of 20 HP sub motor at Pirmuhani . Sl. No Particulars Quantity Rate Amount(Rs) 1 Cost for providing all labours, tools and tackles at site for opening all coupling bolts of 20 HP sub motor & pump and all the electrical connections of motor, taking down motor from its base by top lifting of motor from motor base and stacking the motor at proper place. 1 job 0.00 2 Cost for complete opening of 20 HP sub motor part by part & taken out of top & bottom bearing from bearing houshing and repairing of bearing houshing with weilding with C.I electrode, turning, and finishing as required shape and size. 1 job 0.00 3 Cost for supplying angular contact bearing 6319C3 of SKF Make, if required. 1 job 0.00 4 Cost for greasing the bearing of motor and varnishing, heating & taping of enamelled copper winding wire including required materials like grease and varnish-6 lit.etc. 1 job 0.00 5 Cost for reassembling of rotor & stator of motor and also fitting of bearing in the bearing houshing at repairing place etc. 1 job 0.00 6 Cost for providing all labours, tools and tackles at site for fitting of 25 HP C/F motor on foundation base and refitting nut bolts & testing also. 1 nos 0.00 Total 0.00 Annexure-3 Name of work - Repairing and servicing of 60 Hp soft starter, 25 HP FASD air break Starter & control panel for operation of 20 HP Sub pump . SI.No Particular Quantity Rate Amount(RS) 1 Providing all Labours,tool & tackles for repairing of 25 HP fully automatic stat - delta air break starter with supply,changing and fitting acitiation D type contractor 40 amp - 1no. timer (0-30sec),1 no. over load realy unit (37.6-60)amp,2 no. push botton and changing all internal wiring with suitable PVC Wire & strip as required. 1 Job 0.00 2 Reparing of Panel with changing and fitting (0-150A) Ampere meter- 1no,(0-500V) voltmeter-1no, 1 no selector switch,3 no copper strip bus bar ,2no C.T Coil, 3 no pilot lamp ,100 Amp.and 1 no 25/100 Amp. 16 KAMCCB and changing all interval wiring etc. all complete. 1 Job 0.00 3 Repairing and sevicing of Soft starter suitable for operation of 60 HP sub pump with (a) incomer consisting of 600 Amp. TP 50 kA breaking capacity MCCB- 1 no. LED indicator (RYB)-1 set, 3 phase digital volt meter-1 no., LED frequency meter-1 no., 3 phase digital ampere meter-1 no., CT coil 1000/5- 1 set, ON/OFF Trip indicator (GRY)- 1 set, MCB SP- 2 Amp.-7 nos, APFC panel (7% reactor)-60 KVAR (b) TP 50 kA 400 Amp. MCCB-1 no., terminal speader -1 set, rotory handle-1no., VAF+PF meter-1 no., CT coil-800/5- 1set, 3 pole power Controller-650 Amp-2 nos., LED indicator (RYB)-3 set, Semi conductor fuse base- 6 nos, fuse-6 nos Soft Starter 400 Amp.- 1 set., ON/OFF Trip indicator (GRY)- 1 set, ON/OFF Push Button-1 set copper panel wiring etc. as required in a 4'x8'x3' size panel board. Quantity may vary. 2 job 0.00 Total Rs. 0.00 Annexure-4 "Name of work - Repairing of 60 HP submersible motor of pump set at Pirmuhani I & D plant " SI. NO Particulars Quantity Unit Rate Amount(RS) 1 Cost for Providing all labours,tools and tackles at site for disconnecting the 60 HP submersible pump set and taking out form sump well. 1 P/Job 0.00 2 Cost for dismantaling of monoblock Sub-mersible pump set,taking out rotor form stator of motor and taking out damaged bearing form rotor and cleaning with petrol and ready for repair work. 1 P/Job 0.00 3 "Cost for supplying and fitting Angular contact ball bearing no. 3313A/C3. SKF make. " 1 Each 0.00 4 "Cost for supplying and fitting deep grooved ball bearing no. 6313 ZZ. Skf make. " 1 Each 0.00 5 Cost for supplying and fitting copper cable socket. 5 P/each 0.00 6 Cost for supplying and fitting cable entry kit. 1 P/set 0.00 7 Cost for supplying and fitting joint rubber gasket. 1 Each 0.00 8 Cost for making, supplying and fitting mechanical lock . 1 P/set 0.00 9 Cost for supplying and fitting mechanical seal as per size and sample. 1 Each 0.00 10 Cost for supplying following with GST @ 18%, CP @10% and Labour cess@ 1%. (i) Mobil (super servo-10) hydraulic 7 P/Ltr 0.00 (ii) Servo bearing grease 2 P/Kg 0.00 (iii) Nuts,bolts and key of different sizes. 1 P/Set 0.00 11 Cost for fitting and bearing in rotor of motor assembling rotor in stator of motor complete set. 1 P/Job 0.00 12 Cost for supplying and fitting rubber insertion sheet of size 1/8'' thick(black). 3 p/kg 0.00 13 Cost for transportation of pump motor assembly form site to workshop for repair and back to pump house after repair including all cost of labour for loading and unloding. 1 P/Job 0.00 14 Cost for providing all labours,tools and tackles at site for lowering of motor pump assembly . Fitting and fixing of pump motor assembly to discharge pipe and testing on load. 1 P/Job 0.00 TOTAL 0.00 Annexure-5 Name of work - Repairing and servicing of 60 HP sub motor . Sl. No Particulars Quantity Unit Rate Amount(Rs) 1 Cost for complete opening of 60 HP sub motor part by part & taken out of top & bottom bearing from bearing houshing and repairing of bearing houshing with weilding with C.I electrode, turning, and finishing as required shape and size. 1 p/job 0.00 2 Cost for greasing the bearing of motor and varnishing, heating & taping of enamelled copper winding wire including required materials like grease and varnish-6 lit.etc. 1 p/job 0.00 3 Cost for reassembling of rotor & stator of motor and also fitting of bearing in the bearing houshing at repairing place etc. 1 p/job 0.00 Total 0.00 ANNEXURE-6 Name of work -Servicing, cleaning, greasing and repairing of AB switch & DP structure of 11 KV electric sub - station and 1 x 315 KVA transformer of Pirmuhani . Sl. No Particulars Quantity Rate Amount(Rs) 1 Cost for providing all labours, tools and tackles at site for opening and dismantling of 400 Amp. AB switch such as male & female contact, knife type contact, cleaning & washing each component with petrol properly and resetting them all complete job. 1 jobs. 0.00 2 Cost for supplying & fitting following spares. :- i. Post insulator. 2 Pcs 0.00 ii. Horn gap fuse. ( 1 pcs = 3 nos.) 2 Pcs 0.00 iii. Net fuse for 400 Amp. AB switch. (1 pcs =3 nos.) 2 Pcs 0.00 iv. Copper wire 6 SWG. 2 kg 0.00 v. GI bolts & nuts with washer of different sizes 1.5 kg 0.00 vi. Knife type male & female contact for 400 Amp. AB switch. (1 Pcs = 3 nos) 1 Pcs 0.00 vii. Lightening arrestor for 11 KV sub station 1 Pcs 0.00 ix. Fuse wire 19 no. 0.5 Kg 0.00 3 Cost for providing all labours, tools and tackles at site for opening and dismantling all electrical connections of HT and LT of 1x315 KVA transformer. 1 jobs. 0.00 4 Cost for opening the top cover and other qualizing pipes of transformer for fitting and lightening of HT & LT studs and draining of transformer oil and stacking of transformer oil in container. 1 jobs. 0.00 5 Cost for supplying and fitting following :- (i) LT stud of copper 1 nos. 0.00 (ii) LT bush 1 nos. 0.00 (iii) HT stud of copper 1 nos. 0.00 (iv) HT bush 1 nos. 0.00 (v) Rubberized gasket 1 nos. 0.00 (vi) Transformer oil 40 ltrs. 0.00 6 Cost for tightening of HT & LT studs, refilling of transformer oil and fitting of top cover with ruberised gasket and re-installing equalizing pipes, etc all complete work. 1 jobs. 0.00 7 Cost for PVC sleeving suitable to withstand 11 KV power supply for sleeving of 6 SWG jumpher wire 6 Mtr. 0.00 8 Cost for cutting and removing old and damaged cable socket of LT cable of transformer and doing cable socketing including the cost of 185 mm² cable socket and all requisite insulating materials such as glass tape, PVC tape, empire Tape, etc. 6 nos. 0.00 9 Deduct : Cost of Scrap materials Copper 4 kg 0.00 Total 0.00 Annexure-7 Name of work - Cleaning and desilting of sump, bye pass gate, approach channel, outlet channel etc of Drainage pumping stations under Mechanical works division, Buidco. Sl. No Particulars Quantity Rate "Amount (Rs)" 1 Cost for supplying all labours, tools and suitable tackles for cleaning and desiliting of filled and choked sewage tank, approach channel and inlet chamber etc of drainege pumping station and to lift and disposal of all soils up to a lead of 50 mtr all complete as per specification and direction of E/I at site. 19.25 m³ 0.00 2 Cost for providing all labours, tools, takles & a 10 HP electtric pump set for dewatering the area within brand including cost of hire of electric pump[ set SOR RCD PM6 1001. 24.0 Hr 0.00 3 Cost for providing all labours, tools and tackles at site for repairing, removing rust,dust, scale, smokes etc. from old surface and spray painting two or more coats with anticorrosive bituminous paint of approved brand of two MS gate and channel . 1 job 0.00 Total 0.00 Gr-05 (5) Name of Work- Annual Repairing, maintenance & operation of electro-mechanical accessorries of the pump sets installed in storm drainage pumping plant at S.P. Verma Road for monsoon 2026 for the year 2026-27. SI.No. Description Of Work Qty Unit Rate (RS.) Amount (RS.) 1 Cost for complete repairing and overhauling of 214 HP CF pump set no.-1 as per Annexure-1 1 P/Job 0.00 0.00 2 Cost for complete repairing and overhauling of 75 HP CF pump set no.-2 as per Annexure-2 1 P/Job 0.00 0.00 3 Cost for complete repairing and overhauling of 176 HP CF pump set no.-3 as per Annexure-3 1 P/Job 0.00 0.00 4 Cost for complete repairing and overhauling of 120 HP sub pump set no.-4 as per Annexure-4 1 P/Job 0.00 0.00 5 Cost for complete repairing and overhauling of 156 HP CF pump set no.-5 of diesel pump as per Annexure-5 1 P/Job 0.00 0.00 6 Cost for fitting GI pipe and fitting for repair of vaccum priming line as per Annexure-6 1 P/Job 0.00 0.00 7 Cost for complete repairing and servicing of 156 HP diesel Engine as per Annexure-11 1 P/Job 0.00 0.00 8 Complete repairing and overhauling of 156 HP pump set of diesel engine and its accessories As per Annexure-12 1 P/Job 0.00 0.00 9 Cost for servicing, cleaning, greasing and repairing of AB switch and DP structure of 11 KV electric substation as per Annexure-7 1 P/Job 0.00 0.00 10 Cost for complete repairing and overhauling of 2x10 HP CF vaccum pump set as per Annexure-8 1 P/Job 0.00 0.00 11 Cost for Repairing and overhauling of 3 nos electric motors by dismantaling the motors, double coat varnishing, heating, loop repairing, replacement of the damaged bearing, assembling with all required consumable materials and testing on load. 3 P/Job 0.00 12 Cost for repairing & servicing of panel boards and starter of 1X 214 HP , 1x 75 HP , 1 x 176 HP and 1 x 120 HP pump set as per Annexure-9 1 P/Job 0.00 0.00 13 Cost for providing of spray painting over double coat of paint with red oxide primer of all existing electro-mechanical equipments by removing old paints as per direction of engineer in charge. 1 P/Job 0.00 14 Cost for cleaning and Desilting of sumps as per Annexure-10 . 1 P/Job 0.00 0.00 6 Cost for servicing & filteration of T- oil of 500 KVA out door transformers as per Annexure14 1 P/Job 0.00 0.00 6 Cost for servicing & filteration of T- oil of 2x315 KVA out door transformers as per Annexure15 2 P/Job 0.00 0.00 5 Cost for cleaning, servicing, greasing and repairing of flap valve as per Annexure-13 . 1 P/Job 0.00 0.00 15 Cost for providing supply & fitting of 500 mm dia & 450 mm dia C.I. delivery pipe (10 mm thick) for replacing of old rotten pipe etc as per direction of EI form BCD SOR Sl. No. 18.27.10 20 P/Job 0.00 16 Cost for providing supply & fitting of 500 mm & 450 mm dia. C.I. flange and its all accessories as per direction of E.I from BCD SOR S.L N0. 18.26 4 Per quintal 0.00 17 Cost for providing supply & fitting of 500 mm & 450 mm dia.C.I. flap valve and required all accessories for replacing of old damage flap etc as per direction of EI as per BCD CODE. 7706 6 Mtr. 0.00 18 Cost for Providing & installation of New water level Gauge as per direction of Engineer-in-charge . 1 P/Job 0.00 19 Cost for Complete Reparing ,Overhauling ,Servicing & Functionlity of 10 Ton Manual Chain pulley block Over head crane mounted on DPS as Per Direction of Engineer-in-Charge. 1 P/Job 0.00 20 Cost for construction of 8 m deep earth station as per standard with connection of all electro mechanical equipment with recessing GI flat & GI wiire as per Direction in charge. 3 P/Job 0.00 21 Cost for light wiring in & out the pump house with all required electrical wiring. 1 P/Job 0.00 22 Cost for supply & fitting of 500 mm dia. Automatic butterfly valve ISI marked for 176 HP CF pump as per Direction of Engineer in charge. 1 P/Job 0.00 23 Cost for outdoor cable end terminations heat shrink type LT cable jointing kit suitable for 240 mm2 cable with providing gas cylinder kit etc. As per Direction of E/I. 2 each 0.00 24 Cost for supply & fitting of 300 mm dia. Automatic butterfly valve ISI marked for 75 HP CF pump as per Direction of Engineer in charge. 1 P/Job 0.00 25 Cost for Providing & Laying of 240 Sq.mm 3.5 core copper armoured Cable for 2x350 HP starter to motor with required Jointing kit as per Direction of Engineer -In Charge (make - KEI/Polycab/Havells). 30 m 0.00 26 Maintenance of miscllenious work of Electro-machineries for the period of (01.04.26 to31.03.27) at DPS. The Bidder shall be totally responsible for proper Functioning of DPS with immediate minor & major work repairing like burning of motor, transformer, maintenance of new supply pump & transformer per annum, panel, starter, bearing replacing, cleaning of Campus, Sprinking of Bleaching Powder, pump operation, Functionality of Sluice gate & any other equipments installed or to be install should be Functional in this DPS, Proper flood light, fan, rabber mat, Log Book, ABC store press (4 kg-02nos) & carbon dioxide (4kg-02nos) type fire extingusher required for safety purpose, spray Painting, misc.type of all civil releted work, light wiring, exhaust fan, Name Plate of buidco, wall painting, Recharge of CCTV, availability of 24 hrsx365 days in sufficient quantity of saftey materials, black stone (ballast) transportation and loading, unloadingof any equipment/material, repairing of Civil structure during emergency for water draining as per Direction of E/I. 1 P/Job 0.00 27 Cost for Deployment of 5 nos. x 3 shifts sweepers for removing floating materials from sump, cleaning the premises, taking out the garbages from pump impeller and miscellaneous work during the monsoon period 1st june 2026 to 15th Oct 206 and 02 no. x 1 shift from 16th Oct.2026 to 31.03. 2027. & 1st Aprii' 26 to 31th May' 26 during rest period. 2511 shift 0.00 28 Cost for Deployment of 2 nos. x 3 shifts Highly skilled technician cum pump operators during the monsoon period 1st june 2025 to 15th Oct. 2025 and 01 nos. x 3 shift from rest period (16.10.2025 to 31.03. 2027) & (1st April' 26 to 31th May' 26 ( The no. of pump operators may increase as per situation arisen due to heavy rain fall). 1506 shift 0.00 Total Rs. 0.00 ANNEXURE-01 "Sl. No." Particulars of work Qty. Unit Rate Amount (in Rs.) 1 Cost for providing labour, tools and tackles at site for opening all coupling bolts of 214 HP CF motor and pump and all the electrical connections of motor, taking down motor from its base by top lifting of motor from motor base and stacking the motor at proper place. 1 p/job 0.00 2 Cost for providing all labours, tools and tackles at site for opening of all bolts and nuts of pump casing and bearing housing & taking out of bearing housing together with impeller and coupling and pump shaft (complete rotating assembly). 1 p/job 0.00 3 Cost for opening and dismantling 214 HP pump rotating assembly in workshop and tacking out impeller, pump shaft and bearings from bearing housing, thrust collar, grease shield of DE & NDE, shaft sleeve, bearing cover, etc, and cleaning all inner components for ready for repairing. 1 p/job 0.00 4 Cost for re-metaling, turning and polishing of SS 410 pump shaft and rethreading two points & straightening the shaft by hydraulic pressure machine. 1 p/job 0.00 5 Cost for making,supply and fitting of bronze bush including cutting, turning, polishing and finishing of size. 95 mm ID x 119 mm OD x 200 mm length 1 each 0.00 6 Cost for making 12 nos. 5/8" dia internal thread by top 1 Job. 0.00 7 Cost for supplying and fitting rubber patta with coupling bolts, nuts & washers. 1 P/set 0.00 8 Cost for making, supplying and fitting of CI bearing bush as per sample and size 1 P/set 0.00 9 Cost for supplying and fitting of angular contact ball bearing SKF 3213 A. 1 each 0.00 10 Cost for supplying and fitting of angular contact ball bearing SKF 3313 A. 1 each 0.00 11 Cost for rubber insertion 1/8” thick. 8 p/kg 0.00 13 Cost for making steel key for impeller and coupling pulley. 2 each 0.00 12 Cost for making, supplying and fitting impeller lock screw with washer made of MS with full thread. 1 p/set 0.00 15 Cost for supplying and fitting lock nut. 1 each 0.00 16 Cost for supplying and fitting lock washer. 1 each 0.00 17 Cost for fitting materials such as grease 2 kg, gland packing 5/8”- 2 kg, cotton waste, packing paper, rubber water thrower etc as required at the time of fitting of pump. 1 P/job. 0.00 18 Cost for reassembling of pump shaft, its bearing and accessories into the bearing housing and fitting of impeller in workshop. 1 P/job. 0.00 19 Cost for supplying all labours, tools & tackles at site for fitting of bearing housing along with impeller, placing of motor on its base by top lifting, coupling of motor with pump, checking of alignment of pump with motor, etc all complete 1 P/job. 0.00 20 Cost for transportation of pump and its accessories from S P Verma Road pump house to firm workshop and back to pump house (The total weight of pump and accessories is approximately 500 kg & work shall be undertaken by loading on Pick-up Van). 1 P/job. 0.00 21 Cost for doing all electrical connection of motor & testing on no-load and full load. 1 P/job. 0.00 22 Cost for supplying and fitting bolts and nuts of different sizes with washer. 5 P/Kg 0.00 23 Deduct : Cost of Scrap materials Stainless steel -1 P/Kg 0.00 24 Deduct : Cost of Scrap materials bronze metal -1 P/Kg 0.00 Total 0.00 ANNEXURE-02 "Sl. No." Particulars of work Qty. Unit Rate Amount (in Rs.) 1 Cost for providing labour, tools and tackles at site for opening all coupling bolts of 75 HP CF motor and pump and all the electrical connections of motor, taking down motor from its base by top lifting of motor from motor base and stacking the motor at proper place. 1 p/job 0.00 2 Cost for providing all labours, tools and tackles at site for opening of all bolts and nuts of pump casing and bearing housing & taking out of bearing housing together with impeller and coupling and pump shaft (complete rotating assembly). 1 p/job 0.00 3 Cost for opening and dismantling 75 HP pump rotating assembly in workshop and tacking out impeller, pump shaft and bearings from bearing housing, thrust collar, grease shield of DE & NDE, shaft sleeve, bearing cover, etc, and cleaning all inner components for ready for repairing. 1 p/job 0.00 4 Cost for re-metaling, turning and polishing of SS 410 pump shaft and rethreading two points & straightening the shaft by hydraulic pressure machine. 1 p/job 0.00 5 Cost for making , supplying and fitting of bronze bush of size OD 65 mm ID 58 mm Length 180 mm 1 each 0.00 6 Cost for making 12 nos. 5/8" dia internal thread by tape. 1 Job. 0.00 7 Cost for supplying and fitting rubber patta with coupling bolts, nuts & washers. 1 P/set 0.00 8 Cost for making, supplying and fitting of CI bearing bush as per sample and size 1 P/set 0.00 9 Cost for supplying and fitting of angular contact ball bearing SKF 3213 A. 1 each 0.00 10 Cost for supplying and fitting of angular contact ball bearing SKF 3313 A. 1 each 0.00 11 Cost for rubber insertion 1/8” thick. 15 p/kg 0.00 13 Cost for making steel key for impeller and coupling pulley. 2 each 0.00 12 Cost for making, supplying and fitting impeller lock screw with washer made of MS with full thread. 1 p/set 0.00 15 Cost for supplying and fitting lock nut. 1 each 0.00 16 Cost for supplying and fitting lock washer. 1 each 0.00 17 Cost for fitting materials such as grease 2 kg, gland packing 5/8”- 2 kg, cotton waste, packing paper, rubber water thrower etc as required at the time of fitting of pump. 1 P/job. 0.00 18 Cost for reassembling of pump shaft, its bearing and accessories into the bearing housing and fitting of impeller in workshop. 1 P/job. 0.00 21 Cost for supplying all labours, tools & tackles at site for fitting of bearing housing along with impeller, placing of motor on its base by top lifting, coupling of motor with pump, checking of alignment of pump with motor, etc all complete 1 P/job. 0.00 22 Cost for transportation of pump and its accessories from S P Verma Road pump house to firm workshop and back to pump house (The total weight of pump and accessories is approximately 500 kg & work shall be undertaken by loading on Pick-up Van). 1 P/job. 0.00 23 Cost for doing all electrical connection of motor & testing on no-load and full load. 1 P/job. 0.00 24 Cost for supplying and fitting bolts and nuts of different sizes with washer. 8 P/Kg 0.00 25 Deduct : Cost of Scrap materials Stainless steel -1 P/Kg 0.00 26 Deduct : Cost of Scrap materials bronze metal -1 P/Kg 0.00 Total 0.00 ANNEXURE-03 "Sl. No." Particulars of work Qty. Unit Rate Amount (in Rs.) 1 Cost for providing labour, tools and tackles at site for opening all coupling bolts of 176 HP CF motor and pump and all the electrical connections of motor, taking down motor from its base by top lifting of motor from motor base and stacking the motor at proper place. 1 p/job 0.00 2 Cost for providing all labours, tools and tackles at site for opening of all bolts and nuts of pump casing and bearing housing & taking out of bearing housing together with impeller and coupling and pump shaft (complete rotating assembly). 1 p/job 0.00 3 Cost for opening and dismantling 176 HP pump rotating assembly in workshop and tacking out impeller, pump shaft and bearings from bearing housing, thrust collar, grease shield of DE & NDE, shaft sleeve, bearing cover, etc, and cleaning all inner components for ready for repairing. 1 p/job 0.00 4 Cost for re-metaling, turning and polishing of SS 410 pump shaft and rethreading two points & straightening the shaft by hydraulic pressure machine. 1 p/job 0.00 5 Cost for making & supplying of stuffing box bronze bush of size ID 80 mm OD 95 mm Length 210 mm 1 p/job 0.00 6 Cost for making & supplying bronze stuffing box of size ID 90 mm OD 115 mm Length 40 mm 1 each 0.00 7 Cost for casting, making & supplying C.I. bearing housing of DE & NDE 2 each 0.00 8 Cost for supplying and fitting of rubber patta with bolts & nuts for 10" dia. Motor pump couplings.. 1 P/set 0.00 9 Cost for supplying and fitting of ball bearing SKF 7317 BEP of DE including all taxes, duty & cess. 2 each 0.00 10 Cost for supplying and fitting of roller ball bearing SKF of NDE NU2219ECJ or ECP including all taxes, duty & cess. 1 each 0.00 11 Cost for making and fitting M.S. sleeve in the bearing holder for tight fitting of bearings 2 each 0.00 12 Cost for rubber insertion 1/8” thick. 10 p/kg 0.00 13 Cost for making steel key for impeller and coupling pulley. 2 each 0.00 14 Cost for supplying and fitting SS316 lock nut for bearing as per sample. 1 each 0.00 15 Cost for supplying and fitting SS316 lock washer. 1 each 0.00 16 Cost for supplying and fitting nose type CI dom nut of nose type for impeller as per sample. 1 each 0.00 17 Cost for fitting consumable materials such as grease 2 kg, gland packing 5/8”- 2 kg, cotton waste, packing paper, rubber water thrower etc as required at the time of fitting of pump. 1 P/job. 0.00 18 Cost for reassembling of pump shaft, its bearing and accessories into the bearing housing and fitting of impeller in workshop. 1 P/job. 0.00 19 Cost for supplying all labours, tools & tackles at site for fitting of bearing housing along with impeller with pump casing and tightening all holding bolts and nuts of pump casing, checking alignment of pump bearing housing, etc all complete. 1 P/job. 0.00 20 Cost for transportation of pump and its accessories from S P Verma Road pump house to firm workshop and back to pump house (The total weight of pump and accessories is approximately 600 kg & work shall be undertaken by loading on Pick-up Van). 1 P/job. 0.00 21 Cost for palcing of motor on base, doing coupling of motor with pump, checking and correcting alignment of motor pump and doing all electrical connection of motor & testing on no-load and full load. 1 P/job. 0.00 22 Cost for supplying and fitting bolts and nuts of different sizes with washer. 6 P/Kg 0.00 23 Deduct : Cost of Scrap materials bronze. -5 P/Kg 0.00 24 Deduct : Cost of Scrap materials Stainless steel -8 P/Kg 0.00 Total 0.00 ANNEXURE-04 "Sl. No." Particulars of work Qty. Unit Rate Amount (in Rs.) 1 Cost for Providing all labours,tools and tackles at site for disconnecting the 120 HP submersible pump set and taking out form sump well. 1 P/Job 0.00 2 Cost for dismantaling of monoblock Sub-mersible pump set,taking out rotor form stator of motor and taking out damaged bearing form rotor and cleaning with petrol and ready for repair work. 1 P/Job 0.00 3 "Cost for supplying and fitting Angular contact ball bearing no. 3313A/C3. SKF make. " 1 Each 0.00 4 "Cost for supplying and fitting deep grooved ball bearing no. 6313 ZZ. Skf make. " 1 Each 0.00 5 Cost for supplying and fitting copper cable socket. 5 each 0.00 6 Cost for supplying and fitting cable entry kit. 1 P/set 0.00 7 Cost for supplying and fitting joint rubber gasket. 1 Each 0.00 8 Cost for making, supplying and fitting mechanical lock . 1 P/set 0.00 9 Cost for supplying and fitting mechanical seal as per size and sample. 1 Each 0.00 10 Cost for supplying following with GST @ 18%, CP @10% and Labour cess@ 1%. (i) Mobil (super servo-10) hydraulic 7 P/Ltr 0.00 (ii) Servo bearing grease 2 P/Kg 0.00 (iii) Nuts,bolts and key of different sizes. 1 P/Set 0.00 11 Cost for fitting and bearing in rotor of motor assembling rotor in stator of motor complete set. 1 P/Job 0.00 12 Cost for supplying and fitting rubber insertion sheet of size 1/8'' thick(black). 6 p/kg 0.00 12 Cost for transportation of pump motor assembly form site to workshop for repair and back to pump house after repair including all cost of labour for loading and unloding. 1 P/Job 0.00 13 Cost for providing all labours,tools and tackles at site for lowering of motor pump assembly . Fitting and fixing of pump motor assembly to discharge pipe and testing on load. 1 P/Job 0.00 Total 0.00 ANNEXURE-05 "Sl. No." Particulars of work Qty. Unit Rate Amount (in Rs.) 1 Cost for providing labour, tools and tackles at site for opening all coupling bolts of 156 HP CF motor and pump and all the electrical connections of motor, taking down motor from its base by top lifting of motor from motor base and stacking the motor at proper place. 1 p/job 0.00 2 Cost for providing all labours, tools and tackles at site for opening of all bolts and nuts of pump casing and bearing housing & taking out of bearing housing together with impeller and coupling and pump shaft (complete rotating assembly). 1 p/job 0.00 3 Cost for opening and dismantling 156 HP pump rotating assembly in workshop and tacking out impeller, pump shaft and bearings from bearing housing, thrust collar, grease shield of DE & NDE, shaft sleeve, bearing cover, etc, and cleaning all inner components for ready for repairing. 1 p/job 0.00 4 Cost for re-metaling, turning and polishing of SS 410 pump shaft and rethreading two points & straightening the shaft by hydraulic pressure machine. 1 p/job 0.00 5 Cost for making,supply and fitting of bronze bush including cutting, turning, polishing and finishing of size. 95 mm ID x 119 mm OD x 200 mm length 1 each 0.00 6 Cost for making 12 nos. 5/8" dia internal thread by top 1 Job. 0.00 7 Cost for supplying and fitting rubber patta with coupling bolts, nuts & washers. 1 P/set 0.00 8 Cost for making, supplying and fitting of CI bearing bush as per sample and size 1 P/set 0.00 9 Cost for supplying and fitting of angular contact ball bearing SKF 3213 A. 1 each 0.00 10 Cost for supplying and fitting of angular contact ball bearing SKF 3313 A. 1 each 0.00 11 Cost for rubber insertion 1/8” thick. 5 p/kg 0.00 13 Cost for making steel key for impeller and coupling pulley. 2 each 0.00 12 Cost for making, supplying and fitting impeller lock screw with washer made of MS with full thread. 1 p/set 0.00 15 Cost for supplying and fitting lock nut. 1 each 0.00 16 Cost for supplying and fitting lock washer. 1 each 0.00 17 Cost for fitting materials such as grease 2 kg, gland packing 5/8”- 2 kg, cotton waste, packing paper, rubber water thrower etc as required at the time of fitting of pump. 1 P/job. 0.00 18 Cost for reassembling of pump shaft, its bearing and accessories into the bearing housing and fitting of impeller in workshop. 1 P/job. 0.00 19 Cost for supplying all labours, tools & tackles at site for fitting of bearing housing along with impeller, placing of motor on its base by top lifting, coupling of motor with pump, checking of alignment of pump with motor, etc all complete 1 P/job. 0.00 20 Cost for transportation of pump and its accessories from S P Verma Road pump house to firm workshop and back to pump house (The total weight of pump and accessories is approximately 500 kg & work shall be undertaken by loading on Pick-up Van). 1 P/job. 0.00 21 Cost for doing all electrical connection of motor & testing on no-load and full load. 1 P/job. 0.00 22 Cost for supplying and fitting bolts and nuts of different sizes with washer. 3 P/Kg 0.00 23 Deduct : Cost of Scrap materials Stainless steel -1 P/Kg 0.00 24 Deduct : Cost of Scrap materials bronze metal -1 P/Kg 0.00 Total 0.00 ANNEXURE-06 "Sl. No." Particulars of work Qty. Unit Rate Amount (in Rs.) 1 "Brass full way valve with C.I. wheel (screwed end) 40 mm dia (SOR BCD 18.17)" 2 Each 0.00 2 "Brass full way valve with C.I. wheel (screwed end) 15 mm dia(SOR BCD 18.18)" 3 Each 0.00 3 GI Union Socket of 40 mm dia. (SOR BCD 18.47) 7 Each 0.00 4 G.I. pipe 40 mm dia. (SOR BCD 18.10) 20 P M 0.00 5 G.I. pipe 15 mm dia.(SOR BCD 18.10) 18 P M 0.00 6 G.I. union socket 15 mm(SOR BCD 18.47) 5 Each 0.00 7 Cost for miscellaneous items like G.I. elbow, G.I. nipple, tap, sockets, etc required for repairing the vacuum priming lines. 1 P/job. 0.00 Total 0.00 ANNEXURE-07 "Sl. No." Particulars of work Qty. Unit Rate Amount (in Rs.) 1 Cost for providing all labours, tools and tackles at site for opening and dismantling of 400 Amp. AB switch such as male & female contact, knife type contact, cleaning & washing each component with petrol properly and resetting them all complete job. 3 P/job 0.00 2 Cost for supplying & fitting following spares. :- i. Post insulator. 6 Each 0.00 ii. Horn gap fuse. ( 1 pcs = 3 nos.) 3 Each 0.00 iii. Net fuse for 400 Amp. AB switch. (1 pcs =3 nos.) 3 Each 0.00 iv. Copper wire 6 SWG. 20 P/kg 0.00 v. GI bolts & nuts with washer of different sizes 12 P/kg 0.00 vi. Knife type male & female contact for 400 Amp. AB switch. ( 1 Pcs = 3 nos) 3 Each 0.00 vii Lightening arrestor for 11 KV sub station 9 p/set 0.00 viii Rabit conductor for connection of main incoming feeder. 25 P M 0.00 3 Cost for supply of 2 nos. M.S. channel of size 75 mm x 40 mm x 2.5 M for fitting of lightening arrestor. 40 P/kg 0.00 4 Cost for supply of clamps for fitting the channel on DP. 8 Each 0.00 5 Cost for supply of M.S. clamp for fitting of lightening arrestor on M.S. channel. 6 Each 0.00 6 Cost for providing all labours, tools & tackles at site for fitting and fixing the lightening arrestor on DP by making three nos. hole in the channel, fitting the lightening arrestor on M.S. channel with clamps, fitting the M.S. channel on DP with clamp, all complete work. @ 30% of (2.vii+3+4+5) 3 P/job 0.00 7 Cost for making 20' deep earth station for lightening arrestor and motor & other electrical equipmrnts made of 250 mm x 250 mm x 6 mm thick copper plate with copper flat which shall pass through 40 mm dia. G.I. pipe and fitted with a funnel at top for watering the earth station, the total resistance of the earth stattion shall not be more than 1 ohm. 6 Each 0.00 8 Cost for providing all labours, tools & tackles at site for supplying and laying 25 mm x 3 mm G.I. flat from lightening arrestor and motor & other electrical equipments to the earth stations including the cost of G.I. flat, G.I. bolts & nuts , etc all complete. 60 P/kg 0.00 9 Cost for providing all labours, tools and tackles at site for opening and dismantling all electrical connections of HT and LT of 300 KVA transformer. 3 P/job 0.00 10 Cost for opening the top cover and other equalizing pipes of transformer for fitting and tightening of HT & LT studs and draining of transformer oil and stacking of transformer oil in container. 3 P/job 0.00 11 Cost for supplying and fitting following :- (i) LT stud of copper 6 Each 0.00 (ii) LT bush 6 Each 0.00 (iii) HT stud of copper 5 Each 0.00 (iv) HT bush 5 Each 0.00 (v) Rubberized gasket 3 Each 0.00 (vi) Transformer oil 210 P/ltr. 0.00 12 Cost for tightening of HT & LT studs, refilling of transformer oil and fitting of top cover with ruberised gasket and re-installing equalizing pipes, etc all complete work. 3 P/job 0.00 14 Cost for filtration of transformer oil.(each transformer contains 350 ltr of T. oil) 650 P/ltr. 0.00 15 Cost for PVC sleeving suitable to withstand 11 KV power supply for sleeving of 6 SWG jumpher wire 25 p/mtr 0.00 16 Cost for supplying making and fitting of 4 nos. extension bus bars each of length 2' made of copper strips of size 75 mm x 8 mm x 3 M for connection of cables to the transformers. 3 P/job. 0.00 17 Cost for cutting and removing old and damaged cable socket of LT cable of transformer and doing cable socketing including the cost of 185 mm² cable socket and all requisite insulating materials such as glass tape, PVC tape, empire Tape, etc. 12 Each 0.00 18 Deduct : Cost of Scrap materials Copper -6 P/kg 0.00 Total 0.00 ANNEXURE-08 "Sl. No." Particulars of work Qty. Unit Rate Amount (in Rs.) 1 Cost for providing all labour, tools and tackles at site for opening electrical connection of 10 HP vacuum pump motor, foundation bolts and nuts of pump, GI flange and taking out and removing it from base. 2 P/job. 0.00 2 Cost for dismantling of 10 HP vacuum pump for taking out impeller, pump shaft, etc and cleaning all the components for ready for repair. 2 P/job. 0.00 3 Cost for repairing of steel shaft by remetalling on cut point, turning and polishing of the shaft and making key way groove. 2 P/job. 0.00 4 Cost for repairing GM impeller by brazing the blades of impeller with brass, turning, polishing and facing the blade to bring it to running condition 2 P/job. 0.00 5 Cost for making supplying and fitting GM bush as per sample. 4 Each 0.00 6 Cost for supplying and fitting ball bearing no. 6307 ZNR of SKF. 4 Each 0.00 7 Cost for supplying and fitting oil seal as per sample. 4 Each 0.00 8 Cost for fitting materials such as packing paper, grease, gland packing, nuts and bolts, cotton waste etc required at the time of fitting of pump. 2 Each 0.00 9 Cost for repairing of body (brass discs) by facing both the sides. 2 Each 0.00 10 Cost for supplying and fitting split type GM gland flange. 2 Each 0.00 11 Cost for reassembling of pump with shaft, impeller, bearing set, oil seal, etc accessories in workshop. 2 Each 0.00 12 Cost for transportation of pump from S P Verma Road Pump house to work shop and back to pump house. 2 P/job. 0.00 13 Cost for providing all labour, tools and tackles for reinstallation of motor and pump on base and doing electrical connections and testing all complete. 2 P/job. 0.00 14 Cost for supplying motor pump 3" dia. coupling pulley 2 Each 0.00 15 Cost for making hole as per dia. Of pump & motor shaft and making key way groove in the coupling on lathe machine and fitting & fixing in the pump & motor. 3 P/set 0.00 16 Cost for cutting and removing burnt cable sockets and doing cable socketing of 4 mm² 3 core copper cable of both motor and starter. 12 Each 0.00 17 Deduct : Cost of Scrap materials Gun metal -1 P/Kg 0.00 18 Deduct : Cost of Scrap materials Stainless steel -2 P/Kg 0.00 Total 0.00 ANNEXURE-09 "Sl. No." Particulars of work Qty. Unit Rate Amount (in Rs.) 1 Cost for providing all labours, tools and tackles at site for servicing LT distribution panel board by decarbonisation of its all contact joints, bushes by washing with petrol doing proper insulation at cable terminals with requisite kinds of tapes and repair all internal wiring of above mention starters of pump sets. 4 P/job. 0.00 2 Cost for providing all labours, tools and tackles at site for servicing LT distribution panel board of pump set decarbonisation of its all contact joints, bushes by washing with petrol doing proper insulation at cable terminals with requisite kinds of tapes and repair its all internal wiring. 4 P/job. 0.00 3 Cost for supplying and fitting followings in the panel board of pump sets: - (i) Cost for supply of MCCB DN2-250D with thermal release range 200-250 A and breaking capacity 36 ka in the outgoing feeders of panel boards including all taxes, 1 Each 0.00 (iii) LED pilot lamp standard 12-240 V AC Colour R/Y/G/A 15 Each 0.00 (iv) Volt meter (0-500) volt. 4 Each 0.00 (v) Ampere meter (0-300) Amp. 4 Each 0.00 (vi) CT coil 300/5 6 Each 0.00 (vii) 1.5 sq. mm flexible copper wire for repair of internal wiring of all the panel boards & starters 1 P/coil 0.00 (viii) Making, supplying & fitting, fixing frames made of M.S. flats & angles for fixing of starters on the ground . 1 Each 0.00 (ix) Cost for supply of ACB 400 AMP thermal magnetic release type with breaking capacity 50 ka in the outgoing feeders of panel boards including all taxes, 1 Each 0.00 (x) Cost for supply of C - curve SP 10 Amp. MCB in the 75 HP combine panel boards including all taxes, duty & cess for 75 & 100 HP. Make - L&T 6 Each 0.00 (xi) Cost for supply of C - curve DP 32 Amp. MCB in the combine panel boards including all taxes, 2 Each 0.00 (xii) Cost for supply of MCCB DH 125 with thermal release range 100-125 A and breaking capacity 35 ka in the outgoing feeders of panel boards including all taxes, 1 Each 0.00 4 Cost for opening & dismantling starters by taking out all contactors, bus bars, cleaning & removing dust & vermins blowing machine. 2 Each 0.00 5 Cost for supplying & fitting followings for starters :- (i) CT operated Over load relay CT5MC305ANA3C having relay range for pump set including all taxes, 2 P/job. 0.00 (ii) Contactor MCE 15 RN3.7 pump set including all taxes, 2 Each 0.00 (iii) Electronic timer 415V, 50Hz KRTPN10.0 for pump sets including all taxes, 2 Each 0.00 (iv) Contact set 6-288 of contactor MCE 15 RN3.7 for pump set including all taxes, 2 P/set 0.00 (v) Magnet coil 9-2412 for 125 HP MCE 15 RN3.7 contactor including all taxes, 2 Each 0.00 6 Cost for supply of 12 M x 35 mm x 5 mm copper flat for making bus-bars for connections of cable with starters, ACB & MCCB. 1 P/job. 0.00 7 Cost for supplying and fitting followings in the soft starter of 176 HP & 120 HP pump sets are i. HRC Fuse - 06 nos. ii. MCCB 630 amp - 2 nos iii. TP contactor 220 volt control-01 no. iv.ON/OFF Switch- 02 nos v. soft starter control kit - 01 vi. Soft starter display kit board - 01 vii. soft starter display cable 29 p/38 p flat cable -01 viii.Relay meter ( control line) - 01, ix.Auto switch- 01,x. Relay meter (MPR) - 01 ,xi. single phase preventer- 01,xii. Four step self starting relay- 01,xiii. Amp volt control meter- 01, xiv.MCB- 04 way 63 amp - 01,xv. 63 amp single phase - 04 no. , xvi.2 amp - 6 no.xvii contractor model LC1E 1201, 4 pole 12 amp- 6 nos.xviii LED- 15 nos. xix 110 volt,LED - 06 nos, 440 volt 1 Each 0.00 8 Cost for laying of 70 & 95 sq. mm cable inside pump house including supplying & fitting cable glands, etc, all complete job. 2 Each 0.00 9 Cost for complete repairing and changing of spare parts of APFC panel ( 7% reactor) are 150 KVAR- 01 no , TP 50 KA 630 amp MCCB- 1 no , C.T coil - 600/5 amp - 03 no. MCB 32 amp(TP) - 3 no. Wire 2.5 sq. mm - 01 coil, Power controller - 01 no. , Rotary handle - 01 no, speader - 01 set etc for proper controlling of power factor and also preventing power losses from transformer. 1 job 0.00 10 Cost for doing cable socketing including the cost of 95 mm² cable socket and all requisite insulating materials such as glass tape, PVC tape, empire Tape, etc. 20 Each 0.00 11 Cost for doing cable socketing including the cost of 70 mm² cable socket and all requisite insulating materials such as glass tape, PVC tape, empire Tape, etc. 15 Each 0.00 12 Cost for cutting and removing old and damaged cable socket of panel board & starters and doing cable socketing of 185 mm² cable including the cost of cable socket and required insulating materials. 8 Each 0.00 13 Deduct : Cost of Scrap materials copper -2 P/Kg 0.00 Total 0.00 ANNEXURE-10 "Sl. No." Particulars of work Qty. Unit Rate Amount (in Rs.) 1 Cost for supplying all labours, tools and suitable tackles for cleaning and desiliting of filled and choked sump tank, approach channel and inlet chamber etc of different pumping station and to lift and disposal of all soils and foreign materials all complete as per specification and direction of E/I at site. (I) Sump- 11.15 m X 2.5 m X 2.2 m (avg) = 61.33 m³ 61.33 p/m³ 0.00 2 Supplying all labours, tools and tackles for cleaning and extracting floating materials from the approach channel and bye pass drain outlet channel etc. (i) Sump- 11.15 m x 2.5 m = 28 m² 28 p/m² 0.00 3 Cost for supplying all labour, tools, tackles at site for lift and disposal of soils and foreign materials to a lead of 15 KM all complete with loading and unloading charge all complete. (70% of silt taken out) 42.93 p/m³ 0.00 Total 0.00 ANNEXURE-11 "Sl. No." Particulars of work Unit Qty. Rate Amount (in Rs.) 1 Cost for providing all labours, tools, tackles and an experienced mechanic at site for servicing of 156 HP diesel engine of Greaves make by checking of fuel pump, oil pump, decarbonisation of engine cylinder head and testing of engine on unload and load, etc, all complete with GST, CP & Labour Cess. P/job 1 0.00 2 Cost for supplying and fitting following with GST, CP & Labour Cess.:- (i) Air filter Each 1 0.00 (ii)Diesel filter set P/set 1 0.00 (iii)Lubricating oil filter Each 2 0.00 (iv) Set of Hoses p/set 1 0.00 (v) Fuel Flexible pipe p/set 1 0.00 (vi) Fuse 24V Assly Each 1 0.00 (vii) Coolant 5 ltr cane P/cane 1 0.00 (viii) V Belt 1280 Each 3 0.00 (ix) Relay in electrical panel Each 2 0.00 (x) Solenoid 24 Volt Each 1 0.00 (xi) Lube Oil 20Ltr P/cane 1 0.00 (xii) Head Gasket Each 1 0.00 (xiii) Set of joint Each 1 0.00 (xiv) Set of sealing ring P/set 1 0.00 (xv) Set of Hose clip Each 1 0.00 (xvi) Magnetic Pickup P/set 1 0.00 (xvii) Battery Terminal Each 4 0.00 3 Cost for repairing the leakages in exhaust system by dismantaling the exhaust manifolds and providing the gasket sets and nut bolts and testing on load. P/Job. 1 0.00 4 Cost for dismantaling the power take off system, providing and fitting of cluch set with pressure plate and testing on load at site. P/Job. 1 0.00 5 Cost for checking of leakages in radiator in workshop and repairing of leakages in radiator by replacing damaged portion of copper tube and repairing leakages by soldering of reparable copper pipes with GST, CP & Labour Cess. P/Job. 1 0.00 6 Cost repairing of electrical panel of diesel engine by repalcing all burnt and damaged electrical wires and fuses and ckecking the electrical panel including the cost of labour and electricians with GST, CP & Labour Cess. P/Job. 1 0.00 7 Cost for repairing and servicing of self starter with all materials with GST, CP & Labour Cess. P/job 1 0.00 8 Cost for alternator repairing & servicing with GST, CP & Labour Cess. P/job 1 0.00 Total 0.00 ANNEXURE-12 "Sl. No." Particulars of work Unit Qty. Rate Amount 1 Cost for providing all labours, tools and tackles at site for opening all coupling bolts of 156 HP pump from motor and all electrical connection of motor and opening all nut and bolt of pump casing, bearing housing and taking out of bearing housing together with impeller coupling and pump shaft. P/job 1 0.00 2 Cost for dismentalling of all nut & bolt of pump casing, pump with pump shaft, bearing housing from pump casing including all labour, tools & tackles etc. P/job 1 0.00 3 Cost for remetalling, turning and polishing of SS 410 pump shaft and rethreading two points & straightening the shaft by hydraulic pressure machine including all labours, tools & tackles etc. P/job 1 0.00 4 Cost for making, supply and fitting of bronze nush including cutting. Turning, polishing and finishing of size 100 mm ID x 122 mm OD x 220 mm Length Each 1 0.00 5 Cost for supply and fitting of S cylindercal roller bearing no. SKF 3322 A equivalent for 156 HP pump with GST, CP and Labour Cess. Each 2 0.00 6 Cost for supply and fitting of spherical Roller bearing no. SKF 3322 a equivalent for 156 HP Electric pump with GST,CP & labour cess etc Each 1 0.00 7 Cost for making, supplying and fitting impeller steel key, lock screw and lock washer made of SS 316 with full thread. p/set 1 0.00 8 Repairing of impeller by gas welding at damaged portion, turning, polishing, finishing including supplying all labour, tools and tackles, welding machine hiring, electrode and all consumable items (if required) as per direction of E/I. p/job 1 0.00 9 Cost for supplying and fitting of mechanical seal, oil seal, 'O' rings, water deflector, lantern ring, hexa nut for gland packing, oil filler plug including labour, tools and tackles etc. p/job 1 0.00 10 Cost for supplying and fitting lock nut and lock washer for bearing including labour, tools and tackles. p/set 1 0.00 11 Cost for fitting consumable materials such as grease, gland packing 5/8", cotton waste, packing paper, flexible rubber water thrower etc as required at the time of fitting of pump. p/job 1 0.00 12 Cost for supplying al labours, tools & tackles at size for reassembling of bearing housing along with impeller with pump casing and tightening all holding bolts and nuts of pump casing, checking alignment of pump bearing housing on unload. P/job 1 0.00 13 Providing all labours, tools, tackles for installation of 156 HP C/F pump on foundation,refitting nut-bolt & testing on unload at DPS. P/job 1 0.00 14 Cost for supplying and fitting bolts and nuts of different sizes with washer including labours, tools & tackles. P/kg 10 0.00 15 Cost for supplying and fitting SS coupling bolt as per size and sample including labours, tools & tackles Each 10 0.00 16 Deduct: Cost of scrap materials stainless steel P/kg -2 0.00 Total 0.00 ANNEXURE-13 "Sl. No." Particulars of work Qty. Unit Rate Amount (in Rs.) 1 Cost for providing all labour, tools and tackles at site for opening 16" dia. sluice valve and taking out spindle of sluice valve. 3 P/job. 0.00 2 Cost for repairing of GM spindle of sluice valve by rematalling, turning, polishing the spindle and rethreading square thread about 8" long. 3 Each 0.00 3 Cost for making CI check nut of sluice valve and making square thread as per size and sample of spindle. 3 Each 0.00 4 Cost for making GM ring of sluice valve of size 18" OD x 14" ID of plate of sluice valve. 3 Each 0.00 5 Cost for providing all labour, tools and tackles at site for fitting of sluice valve and spindle check nut & plate complete job. 3 Each 0.00 6 Cost for providing all labour, tools and tackles at site for opening of 16" dia. NR valve and taken out flap, pin shaft etc. 3 Each 0.00 7 Cost for making GM bush of size 1" OD x 1/4" ID x 1" long. 5 Each 0.00 8 Cost for remetalling of CI flap of NR valve about 18 cm² and finishing as per proper ring fitting by grinding. 3 P/job. 0.00 9 Cost for making supplying and fitting SS pin shaft 8" long as per sample with locking arrangement. 3 Each 0.00 10 Cost for providing all labour, tools and tackles at site for fitting of NR valve, flap, & pin shaft etc. 3 P/job. 0.00 11 Cost for providing all labour, tools and tackles at site for opening discharge pipes for taking out & dismantle 1 x 100 HP pump set NR valve and taken out flap, pin shaft etc. 3 Each 0.00 12 Cost for rubber insertion sheet of size 1/8" thick (black) 20 P/Kg 0.00 13 Cost for supplying and fitting bolts and nuts with washer of different sizes. 5 P/Kg 0.00 14 Cost for supplying and fitting graphite gland packing of size 1/2". 3 P/Kg 0.00 15 Deduct : Cost of Scrap materials Gun metal -1.5 P/Kg 0.00 16 Deduct : Cost of Scrap materials Cast iron -5 P/Kg 0.00 Total 0.00 ANNEXURE-14 "Sl. No." Particulars of Works Qty. Unit Rate Amount (in Rs.) 1 Cost for providing all labours, tools and tackles at site for opening and dismantling all electrical connections of HT and LT of 500 KVA transformer with GST, CP & Labour cess. 1 P/job 0.00 2 Cost for opening the top cover and other equalizing pipes of transformer for fitting and tightening of HT & LT studs and draining of transformer oil and stacking of transformer oil in container with GST, CP & Labour cess. 1 P/job 0.00 3 Cost for supplying and fitting following with GST, CP & Labour cess. :- (i) LT stud of copper 3 Each 0.00 (ii) LT bush 3 Each 0.00 (iii) HT stud of copper 3 Each 0.00 (iv) HT bush 3 Each 0.00 (v) Rubberized gaskit 1 Each 0.00 (vi) Transformer oil 120 P/ltr. 0.00 4 Cost for tightening of HT & LT studs, refilling of transformer oil and fitting of top cover with ruberised gaskit and reisnstaling equalizing pipes, etc all complete work with GST, CP & Labour cess. 1 P/job 0.00 5 Cost for filtration of transformer oil with GST, CP & Labour cess. 500 P/ltr. 0.00 6 Cost for PVC sleeving suitable to withstand 11 KV power supply for sleeving of 6 SWG jumpher wire with GST, CP & Labour cess. 10 p/mtr 0.00 7 Cost for supplying making and fitting of 4 nos. extension bus bars each of length 1.25' made of copper strips of size 60 mm x 8 mm x 1.5 M for connection of cables to the transformers. 1 P/job 0.00 8 Cost for cutting and removing old and damaged cable socket of LT cable of transformer and doing cable socketing including the cost of 185 mm² cable socket and all requisite insulating materials such as glass tape, PVC tape, empire Tape, etc with GST, CP & Labour cess. 15 Each 0.00 9 Deduct : Cost of Scrap materials Copper -5 P/kg 0.00 Total 0.00 ANNEXURE-15 Nanme of Work:- Repairing of transformer of 315 KVA transformer and Servicing, Cleaning, greasing, repairing of AB Switch & DP Structure of 11 KV electric sub station. "Sl. No." Particulars of Works Qty. Unit Rate Amount (in Rs.) 1 Cost for providing all labours, tools and tackles at site for opening and dismantling all electrical connections of HT and LT of 315 KVA transformer loading and unloading the transformer on transporation vehicle by using hydraulic crane including the hire cost and reinstallation, commissioning after repairing at DPS. 1 P/job 0.00 2 Cost for opening the top cover and dismantling the same or taking out HT and LT coils from transformer body after draining out transformer oil and stacking in a container, taking out sludge of transformer oil and cleaning inside of transformer body and radiator fins by blowing pressurised oil 1 P/job 0.00 3 cost for providing all labours, tools and taking out HT and LT coil from transformer body by using chain pulley block 1 P/job 0.00 4 Cost for supplying and fitting following:- (i) LT stud of copper 2 nos 0.00 (ii) LT bush 2 nos 0.00 (iii) HT stud of copper 2 nos 0.00 (iv) HT bush 2 nos 0.00 (v) Rubberized gaskit 1 nos 0.00 5 Cost for supplying and fitting of transformer oil 100 ltr. 0.00 6 cost for supplying and filling of transformer oil filteration 200 ltr. 0.00 7 cost forcutting and removing old and damaged cable socket of LT cable of transformer and doing cable socketing including the cost of 185 mm2 cable socket and all requisite insulating materials such as glass tape, pvc tepe, impire tape etc. 2 nos 0.00 8 cost for lightring of HT & LT studs after refilling of transformer oil and fitting of top cover with ruberised gasket and re-installing equalizing pipes, etc allcomplete work. 1 job 0.00 9 cost for providing all labours, tools and tackles at site for opening and dismantling of 400 amp. AB Switch such as male & female contact knife type contact, cleaning & washing each component with petrol properly and resetting them all complete joball electrical connections of HT and LT of 315 KVA transformer loading and unloading the transformer on transporation vehicle by using hydraulic crane including the hire 1 job 0.00 10 cost for supplying & fitting following spares:- Post insulator 2 pcs 0.00 Hom gap fuse (1pcs=3 nos) 2 pcs 0.00 Net fuse for 400 Amp. AB Switch. (1 pcs=3nos) 2 pcs 0.00 Copper wire 6 SWG 2 kg 0.00 GI Bolts & nuts with washer of different size 1.5 kg 0.00 Rabit conductor for connection of main incoming feeder. 5 M 0.00 fuse wire 19 no. 0.5 kg 0.00 11 Cost for PVC sleeving suitable to withstand 11 KV power supply for sleeving of 6 SWG jumpher wire. 5 mtr. 0.00 9 Deduct : Cost of Scrap materials Copper -4 P/kg 0.00 Total 0.00 Sl. No. Abstract Amount Gr05 (1) Annual, repairing , servicing , operation and maintenance of electro mechanical equipment of storm drainage pumping plant of Krishnaghat before monsoon 2026 for the year 2026-27. 0.00 Gr05 (2) Annual repairing, maintenance & operation of electro-mechanical accessorries of the pump sets installed in storm drainage pumping plant at Antaghat for monsoon 2026 for the year 2026-27. 0.00 Gr05 (3) Annual repairing and servicing of electro mechanical equipment of drainage pumping plant of Kadamkuan before monsoon 2026 for the year 2026-27. 0.00 Gr05 (4) Annual repairing , servicing , operation and maintenance of all electro-mechanical equipment of the pumps set installed in drainage IPS pumping plant at Pirmuhani under south Bihar , works division Buidco, patna before monsoon 2026 for the year 2026-27. 0.00 Gr05 (5) Annual Repairing, maintenance & operation of electro-mechanical accessorries of the pump sets installed in storm drainage pumping plant at S.P. Verma Road for monsoon 2026 for the year 2026-27. 0.00

Contact Information