|
Tender For U200 New Control Room Revamping-Brick work demolishing 2 Demolishing brick work manually / by mechanical means including stacking ofserviceable material and disposal of unserviceable material within 50 metres lead asper direction of Engineer-in-Charge.In lime mortar with old mughal bricks 3 RCC demolition 4 Demolishing R.C.C. work manually / by mechanical means including stacking ofsteel bars and disposal of unserviceable material with in 50 metres lead as perdirection of Engineer -in-Charge. 5 Pcc demolishing 6 Demolishing cement concrete manually / by mechanical means including disposal ofmaterial within 50 metres lead as per direction of Engineer - in-Charge.Nominalconcrete 1:4:8 or leaner mix ( including equivalent design mix) 7 Demolishing wooden door 8 Dismantling doors, windows and clerestory windows (steel or wood ) shutterincluding chowkhats, architrave, holdfasts etc. complete and stacking within 50metres lead:Of area beyond 3 sq. metres 9 Dewatering with pump 10 Bailing out water/slush using pump above 5HP and up to 10 HP, includingconveyance to site and erection, cost of fuel, lubrication oil and other stores, pay ofstaff etc complete. All deposits/slush shall be shifted to designated location with in1km lead 11 Demolishing old iron ventilators 12 Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. orR.B. work ( Payment shall be made on the cross sectional area of R.C.C. or R.Bwork) as per direction of Engineer-in-charge. 13 Demolishing existing wooden partition 14 Dismantling wooden boardings in lining of walls and partitions, excluding supportingmembers but including stacking with in 50 metres lead:Upto 10 mm thick 15 Demolishing false ceiling 16 Dismantling roofing including ridges, hips, velleys and gutters etc., and stacking thematerial within 50 metres lead of :Asbestos cement Sheet 17 Excavation work 18 Earth work in excavation by mechanical means (Hydraulic excavator) /manual meansin foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan),including dressing of sides and ramming of bottoms, lift up to 1.5 m, includinggetting out the excavated soil and disposal of surplus excavated soil as directed,within a lead of 50 m.All kinds of soil 19 soling 20 Soling with rough stone of size 200 mm, well packed and filling voids with stonechips and required profile with hammer dressed stones having no side less than 15cm, with minimum depth of 20 cm includingpreparing the bedding surface etc. all complete 21 Providing and laying in position cement concrete of specified grade excluding thecost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mmnominal size derived from natural sources) 22 RCC upto plinth level 23 Providing and laying in position specified grade of reinforced cement concrete,excluding the cost of centering, shuttering, finishing and reinforcement - All work upto plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mmnominal size derived from natural sources) 24 Steel reinforcement work upto plinth level 25 Steel reinforcement for R.C.C work including straightening, cutting, bending, placingin position and binding all complete upto plinth levelMild steel and Medium Tensilesteel bars 26 Solid block masonry upto plinth level 27 Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cmor nearest available size confirming to IS 2185 part I of 1979 for foundation andplinth with thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand ) etccomplete 28 Bituminous painting 29 Painting with black anti- corrosive bitumastic paint of approved brand andmanufacture to give an even shade:Two or more coats on new work 30 Red earth filling 31 Filling with contractor"s own earth ( excluding rock) in trenches, plinth, sides offoundations etc. in layers not exceeding 20 cm in depth, consolidating each depositedlayer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per directionof site Engineer-in-charge 32 RCC for column above plinth level 33 Reinforced cement concrete work in walls (any thickness), including attachedpilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. up tot floor five level excluding cost of centering,shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 gradedstone aggregate 20 mm nominal size derived from natural sources) 34 Solid block masonry 35 Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15cmor nearest available size confirming to IS 2185 part I of 1979 for super structure up tofloor two level with thickness 15cm in :CM 1:6 ( 1 cement : 6 coarse sand) etc 36 RCC beam 37 Reinforced cement concrete work in beams, suspended floors, roofs, having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,staircases and spiral stair cases up to floor five level excluding the cost of centering,shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (ZoneIII) derived from natural sources: 3 graded stone aggregate 20 mm nominal sizederived from natural sources). 38 Steel reinforcement above plinth level 39 Steel reinforcement for R.C.C work including straightening, cutting, bending, placingin position and binding all complete above plinth level.Cold twisted bars 40 Plastering with 12mm cement plaster mix 1:4 41 Plastering with 12 mm cement plaster of mix: 1:4 (1 cement : 4 fine sand ) 42 Ceiling 43 Providing and fixing false ceiling at all height including providing and fixing of framework made of special sections, power pressed from M.S. sheets and galvanized withzinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting ofangle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mmdia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangersof 25x10x0.50 mm of required length with nuts & bolts of required size andother end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mmrunning at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular toG.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mmlong G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed towall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wallscrews @ 230 mm interval, including fixing of gypsum board to ceiling section andperimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c,including jointing and finishing to a flush finish of tapered and square edges of theboard with recommended jointing compound, jointing tapes, finishing with jointingcompound in 3 layers covering upto 150 mm on both sides of joint and two coats ofprimer suitable for board, all as per manufacturer's specification and alsoincluding the cost of making openings for light fittings, grills, diffusers, cutouts madewith frame of perimeter channels suitably fixed, all complete as per drawings,specification and direction of the Engineer in Charge but excluding the cost ofpainting with:12.5 mm thick tapered edge gypsum moisture resistant board 44 Shuttering for footing 45 Centering and shuttering including strutting, etc. and removal of formfor:Foundations, footings, bases of columns, etc for mass concrete 46 Shuttering for column above plinth level 47 Centering and shuttering including strutting, etc. and removal of form for:Columns,Pillars, Piers, Abutments, Posts and Struts 48 Shuttering for beams 49 Centering and shuttering including strutting, etc. and removal of form for:Lintels,beams, plinth beams, girders bressumers and cantilevers 50 Shuttering for slab 51 Centering and shuttering including strutting, etc. and removal of form for:Suspendedfloors, roofs, landings, balconies and access platform 52 Shuttering for sunshade 53 Centering and shuttering including strutting, etc. and removal of form for:Weathershade, Chajjas, corbels etc., including edges 54 Shuttering for stair 55 Centering and shuttering including strutting, etc. and removal of form for:Stairs,(excluding landings ) except spiral - staircases) 56 Applying SBR latex mixed plaster and applying bonding agent 57 Providing, mixing and applying SBR polymer (of approved make such as NitobondSBR/SBR Reomix/Cera SBR Latex of M/s Fosroc/BASF/Cera Chem or Similiarrespectively) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer as per manufactures specification) including surface cleaning and application of bonding slurry to the prepared surface for proper adhesion as per manufacturers specificationas and directions of Engineer in chargeNote:Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made onlyafter proper wet curing has been done and surface has been satisfactorily evaluated by sounding /tapping with a blunt metal instrument of 12 mm average thickness includingscaffoldings upto 4 m height 58 Thixotropic Non shrink mortar 59 Providing and applying single component fibre reinforced thixotropic non shrinkrepair mortar such as BASF EMACO S48CT or FOSROC/BOSTIK product forcolumns, beams, slabs and otherstructural members with 4 ltrs of potable water per 25kg of product, mixing by heavyduty,slow speed drill with spiral mixing paddle or a Pan type mixers etc. afterpouring the water in a mixing vessel, mixed materialshall be applied both by trowel or spray application and finished to get a uniformthickness and finish and all works as per manufactures specifications and as directedby the Engineer in charge, including curing, cost of materials, labour, scaffoldingupto a height of 4 mtr, conveyance etcThe work shall be carried by an agency havingsufficient experience and should ensure a guarantee of 5years. Only skilled andexperienced persons shall be employed for this purpose. 60 Supply and laying first quality vitrified tiles of size 1200*600 61 Providing and laying vitrified floor tiles in different sizes (thickness to be specified bythe manufacturer) with water absorption less than 0.08% and conforming to IS :15622, of approved make, in all colours and shades, laid on 20 mm thick cementmortar 1:4(1 cement : 4 coarse sand), including spacers 3mm and grouting the joints with epoxy which shall be paid extra., complete.Size of Tile 1200x600 mm 62 Epoxy grouting 63 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy groutmix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kgof resin per kg). including filling /grouting and finishing complete as per direction ofEngineer-in-charge.Size of Tile 600x600 mm or nearest 64 providing & fixing anti skid floor tile at toilet 65 Providing and fixing premium quality ceramic digital anti-skid floor tiles ofmake
Kajaria/Nitco/Simpolo/Cera or approved brand conforming to IS :15622 (thickness to be
specified by the manufacturer), in all colours, shadesof size matching to wall tiles or as approved by
Engineer -in-Charge, over12 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) with tilespacers 3mm and jointing with epoxy joint fillers with pigment of matchingshade of approved brand in approved pattern
with two or more desgin tilescomplete. 66 Providing & fixing premium quality ceramic digital wall tile 67 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622(thickness to be specified by the manufacturer), of approved make, in all colours,shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar1:3 (1 cement : 3 coarse sand) and including spacers 3mm and grouting the joints with epoxy which shall be paid extra., complete 68 painting 69 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additivesof required shade:New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over andincluding priming coat of exterior primer applied @ 2.20 kg/ 10 sqm) 70 Window grill 71 Providing and fixing M.S. Grills of required pattern in frames of windows etc. withM.S. flats, square or round bars etc. including priming coat with approved steelprimer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc 72 Aluminium Frame work for Doors windows and partitions 73 Providing and fixing aluminium work for doors, windows, ventilators and partitionswith extruded built up standard tubular sections/ appropriate Z sections and othersections of approved make conforming to IS : 733 and IS: 1285, fixing with dashfasteners of required dia and size, including necessary filling up the gaps at junctions,i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.Aluminium sections shall be smooth, rust free, straight, mitred and jointedmechanically wherever required including cleat angle, Aluminnium snap beading forglazing /paneling, C.P. brass/ stainless steel screws, all complete as per architecturaldrawings and the directions of Engineer-in-charge.(Glazing, paneling and dashfasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating50 micron) 74 Shutter for doors and windows 75 For shutters of doors, windows & ventilators including providing and fixinghinges / pivots and making provision for fixing of fittings wherever requiredincluding the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paidfor separately)Powder coated aluminium (minimum thickness of powder coating 50micron) 76 UV sheet for doors 77 Providing and fixing 4 mm thick UV sheet in panelling fixed in aluminum doors,windows shutters and partition frames with C.P. brass / stainless steel screws , UVSheet finished in two diffrent colours and complete as per architectural drawings anddirections of Engineer - in-Charge 78 Glass 79 Providing and fixing glazing in aluminium door, window, ventilator shutters andpartitions etc. with EPDM rubber / neoprene gasket etc. complete as per thearchitectural drawings and the directions of Engineer - in -Charge. ( Cost ofaluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mmthickness (weight not less than 10kg/sqm) 80 Lock for doors 81 Providing and fixing Brass100 mm mortice latch and lock with 6 levers without pairof handles ( best make of approved quality ) for aluminum doors including necessarycutting and making good etc. complete 82 Hinges 83 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating notless than grade AC 10 as per IS : 1868) transparent or dyed to required colour orshade, with necessary screws etc. complete:100 mm 84 Handles 85 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating notless than grade AC 10 as per IS : 1868) transparent or dyed to required colour orshade, with necessary screws etc. complete:100 mm 86 Tower bolts 87 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barreltype) with necessary screws etc. complete : (Copper oxidized as per IS : 1378)250x10mm 88 FRP door frame 89 Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of crosssection90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of30 mm thickness. The laminated shall be moulded with fire resistant gradeunsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mmthick and shall be filled with suitable wooden block in all the three legs. The frameshall be covered with fiber glass from all sides. M.S. stay shall be provided at thebottom to steady the frame. 90 FRP door shutter 91 Providing and fixing to existing door frames.30 mm thick Fiberglass ReinforcedPlastic (F.R.P) flush door shutter in different plain and wood finish made with fireretardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate allaround, with suitable wooden blocks inside at required places for fixing of fittingsand polyurethane foam (PUF) / Polystyrene foam to be used all filler materialthroughout the hollow panel, casted monoolithically with testing parameters of F.R.P.laminate conforming to table - 3 of IS : 14856, complete as per direction of Engineerin-charge. 92 25 mm PVC concealed 93 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step PVC solventcement and testing of joints complete as per direction of Engineer-in-Charge.Concealed work, including cutting chases and making good the wall etc. 25 mm pipe10kgf /cm2 94 32mm PVC concealed 95 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step PVC solventcement and testing of joints complete as per direction of Engineer-in-Charge.Concealed work, including cutting chases and making good the wall etc. 32 mm pipe10Kgf/cm2 96 50mm PVC concealed 97 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step PVC solventcement and testing of joints complete as per direction of Engineer-in-Charge.Concealed work, including cutting chases and making good the wall etc. 50 mm pipe6 kgf/cm2 98 63mm PVC concealed 99 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes with one step PVC solvent cement andtesting of joints complete as per direction of Engineer-in-Charge. Concealed workincluding cutting chases and making good the wall etc. 63 mm pipe 6 Kgf/cm2 100 32 mm pvc pipe exposed on wall 101 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00m spacing. this includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mmdia 6 Kgf/cm2 - External work - Exposed on wall 102 50mm pvc pipe exposed on wall 103 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step PVC solventcement and testing of joints complete as per direction of Engineer-in-Charge 50 mmdia 6Kgf/cm2 - External work - Exposed on wall 104 110mm pvc pipe trenching and refilling 105 Providing and fixing PVC pipes includes joints of pipes with one step PVC solventcement, trenching, refilling & testing of joints complete as per direction ofEngineer in CHarge. 110 mm dia 4 Kg/cm2 106 63mm dia elbow 107 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement -63 dia 45 degree Elbow 108 63mm 45 degree elbow 109 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement -63 dia 45 degree Elbow 110 63 dia pvc door elbow 111 Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 63 mm dia Door Elbow 112 63 dia tee 113 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipesincluding jointing with PVC solvent cement - 63x63x63 mm dia Tee 114 63mm dia pvc bend 115 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 63 mm dia Bend 116 63mm dia door tee 117 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement -63x63x63 mm dia Door Tee 118 63mm dia vent cowl 119 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 63 mm dia vent cowl 120 110-63mm pvc reducer 121 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement -110x63 mm dia Reducer 122 63x50mm pvc reducer 123 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 63x50 mm dia Reducer 124 63mm dia socket/coupling 125 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 63 mm dia End cap 126 63mm dia coupling 127 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 63 mm dia End cap 128 110mm dia elbow 129 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Elbow 130 110mm dia 45 degree elbow 131 Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow 132 110 mm dia door elbow 133 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement-110 mm dia Door Elbow 134 110mm dia bend 135 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement- 110 mm dia Bend 136 110mm dia tee 137 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipesincluding jointing with PVC solvent cement 110x110x110 mm dia Tee 138 110mm dia door tee 139 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110x110x110 mm dia Door tee 140 110mm dia socket/coupling 141 Providing and fixing PVC moulded fittings/accessories for Rigid PVCpipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling 142 GM ball valve 143 Providing and fixing GM ball valve of approved quality (screwed end) :
25mm nominal bore 144 Providing and fixing CP brass bib cock long body 145 Providing and fixing C.P. brass long body bib cock of approved quality conforming toIS standards and weighing not less than 690 gms.15 mm nominal bore 146 Providing and fixing CP brass stop cock 147 Providing and fixing C.P brass stop cock ( concealed) of standard design and ofapproved make conforming to IS: 893115 mm nominal bore 148 CP brass angle valve 149 Providing and fixing C.P. brass angle valve for basin mixer and geyser points ofapproved quality conforming to IS: 893115 mm nominal bore 150 PVC ball valves 151 Providing and fixing PVC ball valve (ISI marked) of approved brand for Rigid PVCpipes, including jointing with PVC solvent cement:
25mm nominal bore. 152 CP brass shower rose 153 Providing and fixing C.P. brass shower rose with arm of 15 or 20 mminlet:
100 mm diameter 154 SS soap Dish 155 Supplying and fixing Stainless steel soap dish including cost of materials and labourcharges etc complete as per the direction of site Engineer-in-charge. 156 Towel rod 157 Supplying and fixing CP Towel rod 45cm or nearest available length including cost ofmaterials and labour charges etc complete as per the direction of site Engineer-incharge. 158 Health faucet 159 Supplying and fixing CP Health faucet good quality including cost of materials andlabour charges etc. complete as per the direction of site engineer-in-charge 160 CP gratings 161 Providing and fixing CP grating of approved quality.
Rectangular type withopenable circular lid
150 mm nominal size square 100 mm diameter of theinner hinged round grating 162 Floor trap 163 Providing and fixing PVC moulded Floor trap for sanitary pipelines, including jointing PVC pipes with PVC solvent cement and filling gaps with cement groutFloor trap 4 way/3 way 164 Labour charge 165 Miscellaneous labour 166 ISMB 200 167 Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.)trusses etc., including cutting, hoisting,fixing in position and applying a priming coatof approved epoxy primer and 2 or more coats of epoxy paint, including welding andbolted with special shaped washers etc. complete 168 Steel reinforcement paint 169 Providing and applying anti corrosive Nitozinc primer/Cera cte SP CI/ protectosilCIT, two or more coats, over the steel reinforcement as per the manufacturesspecification including scaffolding upto height 4 mtr and as directed by Engineer-incharge. The product shall be applied on the reinforcement surface after throughlycleaning. painted area of steel shall be considered for payment 170 Orissa pattern W.C. pan 171 Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mmSand Cast Iron P or S trap, 10 litter low level white P.V.C.flushing cistern, includingflush pipe, manually controlled device (handle lever) conforming to IS : 7231, withall fittings and fixtures complete, including cutting and making good the walls andfloors wherever require:White Vitreous china Orissa pattern W.C. pan of size580x440 mm with integral type foot rests 172 Providing and fixing white vitreous china pedestal type water closet (European typeW.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, includingflush pipe, with manually controlled device (handle lever), conforming to IS : 7231,with all fittings and fixtures complete, including cutting and making good the wallsand floors wherever required:W.C. pan with ISI marked black solid plastic seat andlid 173 providing & fixing mirror 174 Providing and fixing mirror of superior glass ( of approved quality) and of requiredshape and size with plastic moulded frame of approved make and shade with 6 mmthick hard board backing :Rectangular shape 453x357 mm 175 providing & fixing wash basin 176 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever require:White Vitreous China Flat backwash basin size 450x300 mm with single 15 mm C.P. brass pillar tap 177 Tap pvc PTMT 178 Providing and fixing PTMT bib cock of approved quality and colour.15 mm nominalbore, 86 mm long, weighing not less than 88 gms 179 Providing new septic tank 180 Supplying and installing ready made RCC Septic tank including the cost of carriage,trenching, placing at the level below ground level as specified as per the direction ofengineer in charge incl supply of CC/Sand/06mm aggregate for the preparation of bed) 35 to 50 flush capacity 181 SUPPLY PARTDISTRIBUTION BOARDS 182 Supply of 63A, 3 phase 415V 4 way Verical Distribution boardIn sheet steel enclosure with double door and detachable gland plate, complete with cable entry adaptor box, tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as requiredFor surface mountingWith 63A, 4 pole MCCB as incomer and 1 No.s of 40A 4 pole MCCBs and 2 No. of 32A 4 pole MCCB as outgoing (Including required dummy to close the vaccant spaces)Make of DB: Standard/Havells/ABB/Siemens/Hager/SchneiderMake od MCCB/MCB: Standard/Havells/ABB/Siemens/Hager/Schneider 183 Supply of 40A, 3 phase 415V 4 way Horizontal Distribution boardIn sheet steel enclosure with double door and detachable gland plate, complete with cable entry adaptor box, tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as requiredFor surface mountingWith 40A, 3 phase 4P MCB & 40A, 30mA 3 phase RCCB as incomer and 9 No.s of 20A SP MCBs as outgoingMake of DB: Standard/Havells/ABB/Siemens/Hager/SchneiderMake od MCCB/MCB/RCCB: Standard/Havells/ABB/Siemens/Hager/Schneider 184 Supply of 25A, 3 phase 415V 6 way Horizontal Distribution boardIn sheet steel enclosure with double door and detachable gland plate, complete with cable entry adaptor box, tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as requiredFor surface mountingWith 25A, 3 phase 4P MCB & 25A, 30mA 3 phase RCCB as incomer and 12 No.s of 6A SP MCBs as outgoing (Including required dummy to close the vaccant spaces)Make of DB: Standard/Havells/ABB/Siemens/Hager/SchneiderMake od MCCB/MCB/RCCB: Standard/Havells/ABB/Siemens/Hager/Schneider 185 LIGHTING AND WIRING.LIGHT FIXTURES AND FANS, SWITCHES AND SOCKETS 186 Supply of LED downlight round (Approximate cutout dia 15cm), 10W (Approximate), 230V, 50Hz AC supply, with spring buckle for concealed false ceiling mounting, Lumen efficacy: 100 Lumens/W or above, Lumens: 1000 Lumens or above, THD: 15% or less, PF: 0.90 or above, CRI: 80 or above, Colour temperature: Cool White(5500-6500K), IP: 20 or above, Warranty: Full warranty of 1 year or above 187 Supply of LED downlight round (Approximate cutout dia 20cm), 20W (Approximate), 230V, 50Hz AC supply, with spring buckle for concealed false ceiling mounting, Lumen efficacy: 100 Lumens/W or above, Lumens: 2000 Lumens or above, THD: 15% or less, PF: 0.90 or above, CRI: 80 or above, Colour temperature: Cool White(5500-6500K), IP: 20 or above, Warranty: Full warranty of 1 year or above 188 Supply of LED wall light, 10W (Approximate), 230V, 50Hz AC supply, with spring buckle for concealed false ceiling mounting, Lumen efficacy: 100 Lumens/W or above, Lumens: 1000 Lumens or above, THD: 15% or less, PF: 0.90 or above, CRI: 80 or above, Colour temperature: Cool White(5500-6500K), IP: 20 or above, Warranty: Full warranty of 1 year or above 189 Supply of LED mirror light, 10W (Approximate), 230V, 50Hz AC supply, with spring buckle for concealed false ceiling mounting, Lumen efficacy: 100 Lumens/W or above, Lumens: 1000 Lumens or above, THD: 15% or less, PF: 0.90 or above, CRI: 80 or above, Colour temperature: Cool White(5500-6500K), IP: 20 or above, Warranty: Full warranty of 1 year or above 190 Supply of LED tube light batten, 4 feet, 20W (Approximate), 230V, 50Hz AC supply, Lumen efficacy: 100 Lumens/W or above, Lumens: 2000 Lumens or above, THD: 15% or less, PF: 0.90 or above, CRI: 80 or above, Colour temperature: Cool White(5500-6500K), IP: 20 or above, Warranty: Full warranty of 1 year or above 191 Supply of Exhaust Fan, 225 mm sweep Make:USHA/CROMPTON/BAJAJ/ORIENT/KHAITHAN/HAVELLS 192 Supply of CEILING FANMOTOR TYPE: BLDC230 V, 50 HZ, AC, 1200 MM SWEEP WITH REMOTE CONTROL AND ALL ACCESSORIESSTAR RATING: 5MAKE: ATOMBERG/CROMPTON/HAVELLS/ORIENT/LUCAS/HALONIX. 193 Supply of Electric calling bell, 230V, 50HzMake:Anchor/havells/L&T/Legrand 194 Supply of Bell switch, for 1 module, modular, Make: Legrand, Havells, Anchor, ABB, Honeywell 195 Supply of 6A switch, for 1 module, modular, Make: Legrand, Havells, Anchor, ABB, Honeywell 196 Supply of 25A switch, for 1 module, modular, Make: Legrand, Havells, Anchor, ABB, Honeywell 197 Supply of 6A Socket, for 2 module, modular, Make: Legrand, Havells, Anchor, ABB, Honeywell 198 Supply of 25A Socket, for 2 module, modular, Make: Legrand, Havells, Anchor, ABB, Honeywell 199 Supply of RJ11 Socket, for 1 module, modular, Make: Legrand, Havells, Anchor, ABB, Honeywell 200 Supply of RJ45 Socket, for 1 module, modular, Make: Legrand, Havells, Anchor, ABB, Honeywell 201 Supply of Concealed box, Plate and frame for 2 module, modular, Make: Legrand, Havells, Anchor, ABB, Honeywell 202 Supply of Concealed box, Plate and frame for 3 module, modular, Make: Legrand, Havells, Anchor, ABB, Honeywell 203 Supply of Concealed box, Plate and frame for 4 module, modular, Make: Legrand, Havells, Anchor, ABB, Honeywell 204 Supply of Concealed box, Plate and frame for 6 module, modular, Make: Legrand, Havells, Anchor, ABB, Honeywell 205 Supply of Concealed box, Plate and frame for 12 module, modular, Make: Legrand, Havells, Anchor, ABB, Honeywell 206 Modular type wiring 207 Supply of materials required for copper point wiring for lights, fans and exhaust fan in recessed PVC medium gauge conduit with modular type switch - using 1.5 sq. mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 1.5 sq. mm. PVC insulated copper wire as required, with modular type switch with non metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete. (Excluding supply of Fans, Exhaust fans, Lights, Concealed mounting boxes, Plates and Frames, Switches and Sockets)(Cable make: UNIVERSAL/ECI/CCI/SARK/NICCO/POLYCAB/PARAGON/OMEGA/INCAB/FINOLEX/ TORRENT/PREMIER/LAPP/GOVIND/GLOSTER/HAVELLS/ORBIT/RR CABEL/EMPIRE.) 208 Supply of materials required for copper point wiring for 25A sockets in recessed PVC medium gauge conduit with modular type switch - using 2.5 sq. mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 2.5 sq. mm. PVC insulated copper wire as required, with modular type switch with non metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete. (Excluding supply of Concealed mounting boxes, Plates and Frames, Switches, Sockets)(Cable make: UNIVERSAL/ECI/CCI/SARK/NICCO/POLYCAB/PARAGON/OMEGA/INCAB/FINOLEX/ TORRENT/PREMIER/LAPP/GOVIND/GLOSTER/HAVELLS/ORBIT/RR CABEL/EMPIRE.) 209 Supply of materials required for copper point wiring for calling bell in recessed PVC medium gauge conduit with modular type switch - using 1.5 sq. mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 1.5 sq. mm. PVC insulated copper wire as required, with modular type switch with non metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete. (Excluding supply of Concealed mounting boxes, Plates and Frames, Switches, Sockets)(Cable make: UNIVERSAL/ECI/CCI/SARK/NICCO/POLYCAB/PARAGON/OMEGA/INCAB/FINOLEX/ TORRENT/PREMIER/LAPP/GOVIND/GLOSTER/HAVELLS/ORBIT/RR CABEL/EMPIRE.) 210 Supply of materials required for circuit wiring for RJ11 in PVC medium gauge conduit with modular type switch - using telephone cable (twin flat copper PVC insulated, 2 x 0.5 sq mm, ISI marked, Make: Finolex, Anchor, V-guard, Traco, Sark, Orbit, Polycab) in recessed PVC conduit with modular type socket with non metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete. (Excluding supply of Concealed mounting boxes, Plates and Frames, Sockets) 211 Supply of materials required for circuit wiring for RJ45 sockets in PVC medium gauge conduit with modular type switch - using CAT 6 UTP cable (Make: D-link, Finolex, Polycab, Lapp) in recessed PVC conduit with modular type socket with non metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete. (Excluding supply of Concealed mounting boxes, Plates and Frames, Sockets) 212 Supply of materials required for wiring for Smoke Detectors in recessed PVC medium gauge conduit - using 3 x 1 sq. mm. PVC insulated copper cable in recessed PVC conduit with modular type socket with non metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete. (Excluding supply of Smoke detector)(Cable make: UNIVERSAL/ECI/CCI/SARK/NICCO/POLYCAB/PARAGON/OMEGA/INCAB/FINOLEX/ TORRENT/PREMIER/LAPP/GOVIND/GLOSTER/HAVELLS/ORBIT/RR CABEL/EMPIRE.) 213 Supply of materials required for copper point wiring for lights, fans and exhaust fan in recessed PVC medium gauge conduit with modular type switch - using 1.5 sq. mm. PVC insulated copper conductor stranded cable in srecessed PVC conduit including loop earthing using 1.5 sq. mm. PVC insulated copper wire as required, with modular type switch with non metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete. (Excluding supply of Fans, Exhaust fans, Lights, Concealed mounting boxes, Plates and Frames, Switches and Sockets). (For exceeding 5 meter point wiring. Tthis will be in addition to point wiring rate above).(Cable make: UNIVERSAL/ECI/CCI/SARK/NICCO/POLYCAB/PARAGON/OMEGA/INCAB/FINOLEX/ TORRENT/PREMIER/LAPP/GOVIND/GLOSTER/HAVELLS/ORBIT/RR CABEL/EMPIRE.) 214 Supply of materials required for copper point wiring for 25A sockets in recessed PVC medium gauge conduit with modular type switch - using 2.5 sq. mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 2.5 sq. mm. PVC insulated copper wire as required, with modular type switch with non metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete. (Excluding supply of Concealed mounting boxes, Plates and Frames, Switches, Sockets). (For exceeding 5 meter point wiring. This will be in addition to point wiring rate above).(Cable make: UNIVERSAL/ECI/CCI/SARK/NICCO/POLYCAB/PARAGON/OMEGA/INCAB/FINOLEX/ TORRENT/PREMIER/LAPP/GOVIND/GLOSTER/HAVELLS/ORBIT/RR CABEL/EMPIRE.) 215 Supply of materials required for copper point wiring for calling bell in recessed PVC medium gauge conduit with modular type switch - using 1.5 sq. mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 1.5 sq. mm. PVC insulated copper wire as required, with modular type switch with non metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete. (Excluding supply of Concealed mounting boxes, Plates and Frames, Switches, Sockets). (For exceeding 5 meter point wiring, this will be in addition to point wiring rate above).(Cable make: UNIVERSAL/ECI/CCI/SARK/NICCO/POLYCAB/PARAGON/OMEGA/INCAB/FINOLEX/ TORRENT/PREMIER/LAPP/GOVIND/GLOSTER/HAVELLS/ORBIT/RR CABEL/EMPIRE.) 216 Supply of materials required for Copper circuit wiring in PVC conduit - Circuit Wiring with 1.5 sq.mm PVC insulated, copper conductor, stranded cable in recessed PVC conduit along with 1 no. 1.5 sq. mm. PVC insulated copper wire for loop earthing as required. 217 Supply of materials required for Copper circuit wiring in PVC conduit - Circuit Wiring with 2.5 sq.mm PVC insulated, copper conductor, stranded cable in recessed PVC conduit along with 1 no. 2.5 sq. mm. PVC insulated copper wire for loop earthing as required. 218 Supply of 10 pair telephone junction box and accessories for surface mounting, Make: Syntex, Krone 219 INSTALLATION PARTModular type wiring and Installation 220 Installation, testing and commissioning of LED downlight of all types complete with all accessories etc. in false ceiling including connection with 1.5 sq.mm PVC insulated copper conductor single core cable etc. as required. 221 Installation of ceiling fans, making connections, testing and commissioning etc. with 1.5 sq.mm PVC insulated copper conductor single core cable etc. as required 222 Installation of exhaust fan upto 300 mm sweep in the existing opening including making the holes to suit the size of the above fan making good the damage, connections, testing and commissioning etc. with 1.5 sq.mm PVC insulated copper conductor three core cable etc. as required 223 Installation, testing and commissioning of LED tube lights, wall lights and mirror lights of all types complete with all accessories etc. including connection with 1.5 sq.mm PVC insulated copper conductor single core cable etc. as required. 224 Installation of calling bell at DCW room, making connections, testing and commissioning etc. with 1.5 sq.mm PVC insulated copper conductor single core cable etc. as required 225 Installation, testing and commissioning of Smoke Detectors complete with all accessories etc. including connection with 1.5 sq.mm PVC insulated copper conductor three core cable etc. as required. 226 Fixing of 6/25 amps modular type sockets, switches, bell switches, RJ11 and RJ45 modular sockets (other than included in point wiring) with front plate in surface or in recess including providing and fixing suitable size metal box, inter connections etc as required. 227 Copper point wiring in PVC medium gauge conduit with modular type switch - Wiring for light point/fan point/exhaust fan point using 1.5 sq. mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 1.5 sq. mm. PVC insulated copper wire as required, with modular type switch with non metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete. 228 Copper point wiring in PVC medium gauge conduit with modular type switch - Wiring for socket point using 2.5 sq. mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 4 sq. mm. PVC insulated copper wire as required, with modular type switch with non metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete. 229 Copper point wiring in PVC medium gauge conduit with modular type switch - Wiring for calling bell point using 1.5 sq. mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 1.5 sq. mm. PVC insulated copper wire as required, with modular type switch with non metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete. 230 Copper point wiring in PVC medium gauge conduit for Smoke Detector - Wiring for smoke detector point using 1/1.5 sq. mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 1/1.5 sq. mm. PVC insulated copper 3 core cable as required 231 Copper point wiring for lights, fans and exhaust fan in recessed PVC medium gauge conduit with modular type switch - using 1.5 sq. mm. PVC insulated copper conductor stranded cable in srecessed PVC conduit including loop earthing using 1.5 sq. mm. PVC insulated copper wire as required, with modular type switch with non metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete. (Excluding supply of Fans, Exhaust fans, Lights, Concealed mounting boxes, Plates and Frames, Switches and Sockets). (For exceeding 5 meter point wiring. Tthis will be in addition to point wiring rate above). 232 Copper point wiring for 25A sockets in recessed PVC medium gauge conduit with modular type switch - using 2.5 sq. mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 2.5 sq. mm. PVC insulated copper wire as required, with modular type switch with non metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete. (Excluding supply of Concealed mounting boxes, Plates and Frames, Switches, Sockets). (For exceeding 5 meter point wiring. This will be in addition to point wiring rate above). 233 Copper point wiring for calling bell in recessed PVC medium gauge conduit with modular type switch - using 1.5 sq. mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 1.5 sq. mm. PVC insulated copper wire as required, with modular type switch with non metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete. (Excluding supply of Concealed mounting boxes, Plates and Frames, Switches, Sockets). (For exceeding 5 meter point wiring, this will be in addition to point wiring rate above). 234 Copper circuit wiring in PVC conduit - Circuit Wiring with 1.5 sq.mm PVC insulated, copper conductor, stranded cable in recessed PVC conduit along with 1 no. 1.5 sq. mm. PVC insulated copper wire for loop earthing as required. 235 Copper circuit wiring in PVC conduit - Circuit Wiring with 2.5 sq.mm PVC insulated, copper conductor, stranded cable in recessed PVC conduit along with 1 no. 2.5 sq. mm. PVC insulated copper wire for loop earthing as required. 236 LAN circuit wiring in PVC conduit - Circuit Wiring with UTP/Ethernet cable in recessed PVC conduit as required. 237 Telephone circuit wiring in PVC conduit - Circuit Wiring with two core telephone cable in recessed PVC conduit as required. 238 DB installation and Cabling 239 Installation, testing and commissioning of 63A, 3 phase 415V 4 way Verical Distribution boardIn sheet steel enclosure with double door and detachable gland plate, complete with cable entry adaptor box, tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as requiredFor surface mountingWith 63A, 4 pole MCCB as incomer and 1 No.s of 40A 4 pole MCCBs and 2 No. of 32A 4 pole MCCB as outgoing (Including required dummy to close the vaccant spaces)Make of DB: Standard/Havells/ABB/Siemens/Hager/SchneiderMake od MCCB/MCB: Standard/Havells/ABB/Siemens/Hager/Schneider 240 Installation, testing and commissioning of 40A, 3 phase 415V 4 way Horizontal Distribution boardIn sheet steel enclosure with double door and detachable gland plate, complete with cable entry adaptor box, tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as requiredFor surface mountingWith 40A, 3 phase 4P MCB & 40A, 30mA 3 phase RCCB as incomer and 9 No.s of 20A SP MCBs as outgoingMake of DB: Standard/Havells/ABB/Siemens/Hager/SchneiderMake od MCCB/MCB/RCCB: Standard/Havells/ABB/Siemens/Hager/Schneider 241 Installation, testing and commissioning of 25A, 3 phase 415V 6 way Horizontal Distribution boardIn sheet steel enclosure with double door and detachable gland plate, complete with cable entry adaptor box, tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as requiredFor surface mountingWith 25A, 3 phase 4P MCB & 25A, 30mA 3 phase RCCB as incomer and 12 No.s of 6A SP MCBs as outgoing (Including required dummy to close the vaccant spaces)Make of DB: Standard/Havells/ABB/Siemens/Hager/SchneiderMake od MCCB/MCB/RCCB: Standard/Havells/ABB/Siemens/Hager/Schneider 242 Laying, dressing and clamping of following cables through exsisting trays / structures / racks / columns / walls etc to the new DB .Cable shall be supplied by KMML. All other materials required for clamping are under the scope of contractor. 243 (3.5 x 25 to 3.5 x 50) sq. mm AYFY/XLPE cable 244 Glanding and termination at DB"s side of PVC cable using DC glands/ lugs including supply of cable glands, lugs, aluminium crimping sockets, nuts bolts etc. required for this work. Gland earthing as per standards shall be done by the contractor. 245 (3.5 x 25 to 3.5 x 50) sq. mm AYFY/XLPE cable 246 Telephone switch relocation 247 Installation, testing and commissioning of 10 pair telephone junction box and accessories for surface mounting, Make: Syntex, Krone 248 Approval from Electrical Inspectorate. 249 Preparation of all electrical drawings and obtainig statutory approval from electrical inspectorate for the new DBs Please Enable Macros to View BoQ information
|
