|
Tender For Misc Repair In Main Store Building At Ofcd; Demolition of reinforced cement Concrete of any description and in any position not otherwise specifically provided. , Demolition of Concrete of any description and in any position not otherwise specifically provided for.(unreinforced) , M/L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batterrough finished surfaces of concrete flat surface. , M&L REINFORCED READY MIXED CEMENT CONCRETE (DESIGN MIX)Foundation, including raft footings, foundation beams, plinth beams, bases for column etc., basement slabs, underreamed piles and mass concrete M 25 (OPC 53 Grade cement) make: ultratech, Ambuja, ACC. , S&F of TMT Bars 6 to 8 mm dia and over cut to length,bent to shape required, including cranking bending spirally for hooping for columns,hooking each, binding with and including mild steel wire(annealed) n.less than 0.9mm dia or securing with clips . , M&L for cement concreteType A 0, 1:1.5:3 ( M20), 12.5 mm graded aggregate. , Dismantling structural steel work including doors, gates but excluding framed truss etc , S&F Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pullgear operated type with bevel gear box and crank handle.1.25 mm thick sheet. , M&L forpreparing new steel surfaces, apply one coat of red oxide/ zinc chrome, synthetic enamel(ordinary/ tint) painting two coat Surfaces of anydescription, not otherwise descri-bed, over 10cm width or girth steel based surface (Asian paints / Nerolac/ Berger).approved by OFCd. , Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. , M&L rendering 15mm thick on fair faces of brick work or concrete surfaces1:6 cement plaster and rendering is to be finished even and smooth (without using extra lime or cement)® , M&L for 3mm thick wall care putty on wall. , M&L for 3mm thick wall care putty on ceiling. , M&L for Distempering two coats to ceiling surface with distemper oil emulsion, white or tinted. (Asian, Nerolac, Berger) , Dismantling asbestos cementcorrugated,semicorrugated, etc.) sheets in roof coverings. , S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof vering /cladding to wall, fixed with self tapping screws as specified.(make: TATA, Bhusan, Jindal) , Cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3. , M&L for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes.conforming to I. S.1161- 1979 grade St.-240 , Dismantling boarding, any description, fixed in any position with nails. , S & F of Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to tre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. , S&f for Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish (Frame work for ceiling shall be measured and paid separately) thickness 8mm. , M & L for taking down the Shutters of any description exc 2sqm each and remove to store. , S&F of Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete. Fe- 290 (Gde E- 165) , S & F of Mild steel, plain, black sheet of 1.25 mm in wall cladding ,steel gates and similar work, cut to size, holes punched; including round headed screws,clout nails or rivetsand fixed to wood or steel framing withplain 40 mm lap joints with riveted or welded seams, including bendingor turning up, mitredangles, etc. as required , Removing building materials etc. to a distance of 5 km or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination.(0.62 cum =One load) , Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete , M&L for100 mm bitumen Flash strip. Make: STP, IWL. , M&L for (i) Surface preparation: The concrete substrate must be sound and of sufficient compressive strength (minimum 20 N/mm2) with a minimum pull off strength of 1.5 N/mm2 for durable and lasting flooring. The substrate must be level, clean, dry and free of all contaminants such as dirt, oil, grease etc. All previous floor coating if any must be mechanically removed to the maximum extent possible. It is acceptable to relay on floor coating that has a firm bond(pull out strength of 1.5N/mm2). Concrete substrates must be prepared mechanically using abrasive blast cleaning, scarifying or grinding equipment to remove cement laitance and achieve an open textured surface. Weak concrete must be re moved and surface defects such as blowholes and voids must be fully exposed.Repairs to the substrate, filling of blowholes/voids and surface leveling must be carried out using appropriate repair product. The concrete or screed substrate has to be primed or leveled in order to achieve an even surface. High spots must be removed by grinding. (ii) Providing and installing MYK arment, Fosroc, Sika 6mm thick Polyurathene flooring using Top HPU 6,4 components with outstanding wearing properties self smoothing heavy duty polyurethane flooring, mixing 4 components by mechanical means,mixed screedTop HPU 6(Thickness 4.0 mm) over completely driedcoats ofHPU Sc as Scratch coat etc spreading the mix using trowel, including surface roughening, groove cutting, cleaning, groove filling usingTop HPU 6 allowing it to dry completely, etc and complete as per manufacturer's specification. The parameters forTop HPU 4 are as follows: Compressive strength (IS9162-1979) Approx. 53 N/mm² (BS6319) Tensile strength (IS9162-1979) Approx. 7 N/mm², Flexural strength (IS9162-1979) Approx. 12 N/mm², Adhesive pullout bond strength in N/mm² (ASTM D 4541-2002) > 1.5 N/mm² (concrete failure) Taber abrasion resistance (1000 g, 1000cycles) (ASTM D4060) weight loss, mg CS17 wheel: 125, H22 wheel 1500, Shore D Hardness 75 Slip resistance (under BS 8204: Part 2: 2002(9),wet and dry ) Satisfactory Impact resistance (under BS 8204: Part 1: 1999) Satisfactory Water absorption 0 ml, Surface spread of flame (BS 476: Part 7) Class 2 Foot traffic @ 30degC After 36 hrs, Light traffic @ 30degC After 48 hrs, Full traffic @ 30degC After 60 hrs, Full cure @ 30degC After 7 days( make: MYK arment, Fosroc, Sika) (iii) Providing and cleaning of pot holes with wire brush and cut the groove of damange portion and fill it with MYK ERM (Epoxy Repair Mortar) FloArm ERM is a three-component filled epoxy ( make: MYKarment, fosroc or equivalent) , Supply and apply of Resin mortar with the following properties: Solvent free High compressive and flexural strength High resistance to mechanical loadingRepair of Damage and Voids in Concrete:Apply FloArm ERM to the voids over the wet primer in one application, compact and strike off level with thesurface ( make: MYKarment, fosroc or equivalent)
|
