|
Supply Of Civil Materials Including Galvanized Wire, Hdpe Pipes, Lt Armoured Cable And Adventure Facilities At Rajgir=1 Providing and fixing galvanised steel wire rope of 48–50 mm diameter, in sets, conforming to IS: 2266 / IS: 3938 (latest revision), manufactured from high tensile steel wires, hot dip galvanised with uniform zinc coating, suitable for outdoor structural use, complete with necessary end terminations, clamps, thimbles, sockets, turnbuckles and all accessories as per approved engineering drawings, specifications and directions of Engineer-in-Charge, including cutting, laying, tensioning, alignment, testing and commissioning, all complete. 2 Providing, laying, jointing and testing HDPE (High Density Polyethylene) pipe of 90–100 mm diameter, conforming to IS: 4984 (latest revision), PE-100 grade, pressure rating as specified (PN-6 / PN-8 / PN-10 / PN-16), suitable for water supply / drainage / utility services, including all fittings such as bends, tees, reducers, couplers, end caps etc., jointing by butt fusion / electrofusion including jointing material, trench excavation (if required), laying, alignment, refilling, compaction, hydraulic testing and commissioning, complete as per drawings, specifications and directions of Engineer-in-Charge. 3 Providing, laying, jointing, testing and commissioning LT armoured power cable of required size and number of cores, 1.1 kV grade, aluminium / copper conductor, PVC / XLPE insulated, PVC sheathed, steel wire armoured, conforming to IS: 7098 (Part-1) / IS: 1554 (Part-1) (latest revision), suitable for underground / above-ground installation, including supply of cable, necessary cable glands, lugs, jointing kits, identification tags, laying in trench / ducts / cable trays, sand cushioning, brick protection / warning tape, refilling, compaction, termination at both ends, testing and commissioning, complete as per drawings, specifications and directions of Engineer-in-Charge. i 10 sqmm ii 25 sqmm iii 50 sqmm iv 95 sqmm v 120 sqmm 4 Development of Climbing Wall: Design, supply, fabrication, installation, and commissioning of an artificial climbing wall of approximate size 10 feet width × 30 feet height, including MS/steel structural framework, FRP/marine plywood wall panels with anti-slip textured finish, climbing holds of various configurations, top anchor points, belay and safety systems, safety mats at base, all fittings and accessories, surface finishing and corrosion protection, testing and trial run, complete in all respects as per applicable international safety standards, with the rate inclusive of all materials, labour, transportation, installation, and commissioning. 5 Development of Activity Tower: Design, supply, fabrication, installation, and commissioning of an activity tower of approximate size 14 feet width × 12 feet length × 40 feet height, comprising MS/steel structural framework designed for dynamic loads, multiple activity elements/platforms (such as climbing, rope, balance or adventure components as specified), access ladders/stairs, safety railings, anchor points, belay and safety systems, safety nets/mats at base, all fittings, fasteners, surface finishing, corrosion protection, testing, and trial run, complete in all respects as per applicable safety standards, with the rate inclusive of all materials, labour, transportation, installation, and commissioning. 6 Low Rope Courses: Design, supply, fabrication, installation, and commissioning of a multi-activity low rope course comprising different rope course activities, installed on poles of approximate 20 feet height, within an overall course area of about 20 feet × 40 feet, including high-strength ropes, cables, connectors, platforms, anchor points, safety systems, base safety arrangements, all fittings and accessories, surface finishing, testing, and trial run, complete in all respects as per applicable safety standards, with the rate inclusive of all materials, labour, transportation, installation, and commissioning. 7 Sky Roller (Double Lane): Design, supply, fabrication, installation, and commissioning of a double-lane Sky Roller of approximate 60 meters length, including overhead track system, trolleys with bearings, safety harnesses and lanyards, anchor points, platforms at start and end, braking and stopping mechanisms, all safety fittings, accessories, surface finishing, corrosion protection, testing, and trial run, complete in all respects as per applicable safety standards, with the rate inclusive of all materials, labour, transportation, installation, and commissioning. 8 Development of Landing Tower (Sky Roller): Design, supply, fabrication, installation, and commissioning of a landing tower for Sky Roller of approximate size 12 feet × 12 feet × 20 feet height, comprising MS/steel structural framework designed for operational loads, landing platform with safety railings, access ladder/stair, anchor points, braking/landing arrangements, all fittings and accessories, surface finishing and corrosion protection, testing, and trial run, complete in all respects as per applicable safety standards, with the rate inclusive of all materials, labour, transportation, installation, and commissioning. 9 Zip Line Roller Coaster: Design, supply, fabrication, installation, and commissioning of an elevated Sky Roller Coaster (Zip Line type) of approximate 100 meters length, designed to run on stainless steel pulley system, including MS/steel support structures and towers, SS cables/tracks, pulleys with bearings, rider trolley, safety harnesses and lanyards, anchor and tensioning systems, start and landing platforms, braking and stopping mechanisms, all safety fittings and accessories, surface finishing and corrosion protection, testing, and trial run, complete in all respects as per applicable safety standards, with the rate inclusive of all materials, labour, transportation, installation, and commissioning. 10 Rocket Ejection: Design, supply, fabrication, installation, and commissioning of a Rocket Ejection activity of approximate size 15 feet (width) × 30 feet (length) × 42 feet (height), including MS/steel structural framework, elastic/propulsion system, launch and landing platforms, safety harnesses, ropes and lanyards, anchor points, shock-absorbing mechanisms, base safety mats, all fittings and accessories, surface finishing and corrosion protection, testing, and trial run, complete in all respects as per applicable safety standards, with the rate inclusive of all materials, labour, transportation, installation, and commissioning. 11 Archery & Rifle Shooting (Equipment Supply): Supply of 4 sets of archery equipment and 4 sets of rifle shooting equipment, including bows, arrows, targets, rifles, pellets/ammunition, shooting stands, and all necessary accessories. The equipment is to be installed and made operational within the provided rifle and archery range, complete in all respects, with the rate inclusive of supply, delivery, and installation.
|
