|
Tender For Provision Of Otm accommodation For Gdcc At Af Stn Rajokri Under Ge (Af) Gurgaon- 1 Surface dressing n.exc 15 cm deep and getting out soft/loose soil all as specified and as directed. 2 Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft/loose soil vomplete all as specified and as directed. 3 Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on planand n exc 1.5 m in depth and getting out soft/loose soilcomplete all as specified and directed. 4 Excavating in trenches, n exc 1.5 m wide andexc 1.5 m in depth but n.exc 3.00 m; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on planand n exc 1.5 m in depth and getting out soft/loose soil complete all as specified. 5 M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete, sub base complete all as specified. 6 M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as infoundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified. 7 M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as inColumns, pillars, piers, posts and struts complete all as specified. 8 M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as inSlabs supported on walls,beams and columns in floors,roofs, complete all as specified. 9 M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in Beams, cantilevers, bressummers, lintel over 1.5 span complete all as specified. 10 M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in Chajjas complete all as specified. 11 Use of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter (rough finished surface) complete all as specified. 12 Use of formwork to sides of pillars,posts, struts, piers, columns and stanchions square/rectangular/polygonal) rough finished surface complete all as specified. 13 Use of formwork to soffits of suspended slabs such as roof slabs, floorslabs, landings and similar work not exceeding 200 mm thick rough finishedin flat surface complete all as specified. 14 Use of formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers,lintels, cantilevers, shelvesincluding supports,overhangs,etc. also splays between floors in rough finished flat surfaces and etc complete all as specified. 15 Use of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon tal or sloping and similar work exc 10cm but n exc 20cm wide (rough finished surface)complete all as specified. 16 M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified. 17 All as peritem No. 15 above but 5 mm dia & over upto & including 10 mm dia in stirrups,spacers and binders, complete all as specified. 18 M&L for brick work with sub class "B" brick, straight or curved on plan exc 6.0 mtr mean radius built in cement mortar 1:6 etc complete all as specified. 19 M&L for half brick work with sub class "B" old size brick, straight or curved on plan exc 6.0 mtr mean radius built in cement mortar 1:4 etc complete all as specified. 20 M&L for rendering 15 mm thick in cement mortar (1:6) onbrick work or concrete surfaces finished even and smooth (without using extra cement) complete all as specified. 21 M&L for 15 mm thick plastering in two layers (10+5) mm in cement mortar (1:4) on brick or concrete surfaces including rendering on fins, fascias, chajja, parapets etc and finishing the surfaces even and fair (without using extra cement), top layer shall be with WPC as per manufacturer"s instruction and complete all as specified.Note: WPC shall be measured and paid separately. 22 M&L rendering 10mm thick in cement mortar (1:3) as in ceilings finished even and smooth (without using extra cement) complete all as specified. 23 M&L for preparation ofnewly plastered or unplastered/undecorated surface of wall and applying two coats of oil bound distemper over one coat of primer complete all as specified. 24 M&L for preparation ofnewly plastered or unplastered/undecorated surface of ceiling and applying two coats of oil bound distemper over one coat of primer complete all as specified 25 M&L for preparation ofnewly plastered surface of wall and applying Two coats of wheather proofing exterior acrylic emulsion paint ( Camouflage Pattern)over a coat of primer premium quality complete all as specified and as directed. 26 M&L for providing 3mm thick wall care putty on wall before applying oil bound distemper and making the surface uniform all as specified. 27 M&L for providing 3mm thick wall care putty on ceiling before applying oil bound distemper and making the surface uniform all as specified. 28 Supply only intergral water proofing compound ISI Marked complete all as specified. 29 M&L for Hardcore (broken stone or boulders) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete. 30 M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified. 31 M&L for 75 mm thick cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregates) asin sub base of flooing etc complete all as specified. 32 M&L for cement concrete(1:2:4) type B-0 (using 12.5 mm graded stone aggregates) 25 mm thick as in sub base of flooring/tiles etc completeall as specified. 33 M&L for screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:4)for bedding of tilescomplete all as specified. 34 M&L 10 mm thick rendering in cement mortar (1:3) on vertical surfaces for backing of tiles/granite etc complete all as specified. 35 M & L for Granite (of any type) tiles 18-20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polish etc completed all as specified. 36 M & L Granite (of any type) work (table rubbed and polished) 20mm thick for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, etc complete all spd and directed. 37 M&L forNon - skid (joint free) coloured Vitrified Ceramic tiles 7 to 8 mm thickarea of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified. 38 M&L for Non - skid (joint free) coloured Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified. 39 M&L for Glazed ceramic colouredtiles in vertical surface 450X 300X 6 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified. 40 M&L for PCC 1:2:4 type B1 (using 20mm graded stoneaggregates) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified. 41 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soft/loose soil etc complete all as specified. 42 Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified. 43 M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surfacecomplete all as specified. 44 M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface areacomplete all as specified. 45 M&L for 15 mm thick plaster in cement mortar (1:4) mixed with water proofing compound on roof slabs finished even and smooth without using extra cementcomplete all as specified. Notes : WPC shall be measured and paid seperately. 46 M&L for water proofing treatment with APP (Atactic Polypropylene) modified polymeric prefabricated five layer membrane over roof consisting of cleaning of concrete or plaster surface of roof & parapet walls and applying evenly a bitumen primer confirming to IS 3488 @ 0.40 Kg per sqmlaid using buten torch and sealing all joints of APP modified polymeric water proofing membrane minimum weight 3.6 kg/sqm reinforced with non woven polyester fabric (weight not less than 160 grams per sqm) unrolled and bonded to substrata with logitudinal and end laps 100 mm and 150 mm respectively as per manufacturer"s instructions incl two coats of water proofing paint with aluminium finish on top complete all as specified. 47 S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 48 S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. 49 S&F 100 mm Butt hinges, Stainless steel and fixed complete all as specified. 50 S&F 200mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified. 51 S&F 150 mm size extruded aluminium alloy handles fabricatedtype anodised and fixed. 52 S & F 300 mm long mild steel ordinary rat tail rod pattern door spring including roller and roller plate complete all as specified and directed by engineer incharge 53 S&F 250 mm long aluminium alloyanodised sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast sections or cast aluminium alloy complete all as specified. 54 S&F in repairs 19 mm dia Aluminium curtain rod with powder coated along with ornamental attachment at both ends and one set of ornamental decorative MS clamps to fixed to walls complete all as specified and directed. 55 S&F GI tubes medium grade with all fitting and fixed complete to walls, ceilings or laid infloors 15mm bore complete all as specified and directed. 56 S&F tubes 20 mm bore dia, medium grade, galvanised, with allfitting and fixed complete to walls and ceilings or laid in floos,complete all as specified and directed. 57 M & LVitreous china wash down water closet pan, pedestal pattern (EWC) white, including seat cover , fixing bolts connection to trap & to flush pipe fixed in repairs complete all as directed by the Engineer-in-charge. 58 S&F 500 ltrsrotational moulded polyethylene water storage tanks (cylindrical verical with closed top) hoisted and fixed in position including ball valve of 20 mm dia complete all as specifed and directed. 59 S & F for Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed,Bore dia of pipe in 20 mm, etc complete all as specifed and directed. 60 S&F for Vitreous China Urinal, Half stall type, white including waste pipe and water splinder, etc complete all as specifed and directed. 61 S&F vitreous china pedestal wash hand basin (flat back) of size 550x400mmincluding one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, with & including 32 mm dia PVC waste pipe with connector,including cutting for and pinning in ends of brackets completeall as specified. 62 Shelf of PTMT fixed with and including chromium plated brass screws and wooden/ plastic cleates. 63 S&F grating doom100mm dia size with PTMT complete all as specified and directed. 64 S&F PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic actiontype with inlet ball valve and float, handle with & including bracket andPVC flush pipe 32 mm borecomplete all as specified. 65 S&F bib taps, long body,brass, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule orto GI socket complete all as specified. 66 Supply and fixing for Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including makingconnections and fixed in position complete in all respect complete all as specified and directed by Engr-in-Charge. 67 S&F fancy typeAngle stop cock with flange, 15 mm nominal bore, brass, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified. 68 S&FCentre hole basinmixture with hot or cold mountedtap of 15mm bore dia, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts fancy type screwed for iron pipe, complete all as directed by EIC. 69 S&F PVC connection 450 mm long suitable for 15 mm GI pipe with two brass nuts & rubber washers complete all as specified. 70 S&FPVC looking mirrorof selected quality of size 600 mm x450 mm on 4 mm thickwith framefixedscrew and cup- washers complete all as specified. 71 S&F tubular towel rail 20mm dia type brass chrormium plated 600mm long between flanges complete all as specified and as directed 72 S&F PVC (SWR) floor trap plain with gratinghaving dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified. 73 S&F110mm dia PVC (SWR) pipe and single socketed in any length with rubber ring joint fixed to wall.complete all as specified 74 S&F PVC (SWR) bends any radius 110mm bore. Complete all as specified 75 S&F PVC (SWR) junction single, (single T) equal or unequal 110mm bore complete all as specified. 76 S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors 75mm bore. 77 S&F PVC (SWR) bends any radius 75mm bore. 78 S&F PVC (SWR) junction single, (single T) equal or unequal 75 mm bore complete all as specified. 79 S&F PVC (SWR) vent cowl 110 mm bore complete all as specified. 80 Excavation in post holes (or similar holes) each n exc 0.5 cum, getting out soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface.complete all as specified 81 M&LCement concrete Type B2 1:2:4 (40 mm graded aggregate) asin foundation filling and mass concrete for column post.complete all as specified 82 M & L Mild steel work as in posts, sturts & vertical colmns using ERWor induction butt welded tubes coforming to IS 1161-1979 grade st-240 etc complete with gusset plates,base plates etc including a shop coat of red oxide primer complete all as specified and directed 83 M & L Mild steel work as in roof trusses including special shaped washers etc complete using ERWor induction butt welded tubes coforming to IS 1161-1979 grade st-240 etc including a shop coat of red oxide primer complete all as speciied anddirected. 84 Preparation of new steel surfaces and applying one coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge. 85 S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified 86 Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified. 87 Cutting holes in Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall, exc half brick but n exc one brick walls,Ditto, but in brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar,complete all as spd and directed. 88 S&F factory made uPVC texturecolour (wood finish) casement (openable)window with pleated mesh area made of extrudedprofiles with wall thickness of 2.0mm (+/0.2mm). Window profile with hollow section with multi chamber, frame (60mmx58mm),sash (60mmx73mm),T profile (One vertical length in between two shutters) (60mmx74mm) Glazing bead(35x20mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware EPDM gasket 1.2 + -0.2 mm thick galvanized steel frame (28mmx21.5mm) sash (31mmx27.5mm)"T" profile (27mmx17mm) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners.Hardware : [ casementhandle made of zinc alloyed (while powder coated) Butt hinges of zinc alloyed (white powder coated) transmission gear made of mild steel with multi point locking system)and 5mm thick glazing with selected quality glass complete all as specified and as directed. Note : Selected quality clear Glassandmeshcost of all other connected accessories deemed included in unit rate. Net opening will be measured for payment purpose. 89 S&F factory made uPVC texture colour (wood finish) casement (Open-able) door with pleated mesh made of extruded profile with wall thickness of 2.0mm (+/- 0.2mm). door profile with hollow section with multi chamber, frame (60mmx58mm) T profile (One vertical length in between two shutters) (60mmx71mm) Glazing bead corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware EPDM gasket + -0.2 mm thick galvanized steel frame (28mmx21.5mm) "T" profile (27mmx17mm) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware : [ three track window/ door handle made of zinc alloyed (while powder coated) Corner strikers: cylinder, Door transmission gear made of mild steel with multi point locking system with strikes, 3D hinges of zinc alloyed (white powder coated)] and 5mm thick glazing with selected quality glass. Note : Selected quality clear Glassandmeshcost of all other connected accessories deemed included in unit rate. Net opening will be measured for payment purpose. 90 M&L 100 mm thick PCC 1:4:8 tybe D-2 using 40mm stone aggregate as in subbase complete all as specified and directed. 91 M&L for providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved, design & pattern as in footpath , parks , lawns,drive ways or light traffic parking etc. of required strength , thickness & size/shape, made by table vibratory method using PU mould , laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand , compacting and proper embedding/laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator,filling joints with sand andcutting of paver block as per required size and pattern,finishing and sweeping extra sand. Complete all as specified 92 Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on planand n exc 1.5 m in depth and getting out soft/loose soilcomplete all as specified and directed. 93 M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete, sub base complete all as specified. 94 M&L for brick work with sub class ‘B’ bricks old size straight or curved on plan exc 6.0 m mean radius built in cement mortar (1:4) complete all as specified. 95 M&L for 15 mm thick plastering in two layers (10+5) mm in cement mortar (1:4) on brick or concrete surfaces including rendering on fins, fascias, chajja, parapets, manholes etc and finishing the surfaces even and fair (without using extra cement), top layer shall be with WPC as per manufacturer"s instruction and complete all as specified.Note: WPC shall be measured and paid separately. 96 Supply only intergral water proofing compound ISI Marked complete all as specified. 97 M&L for cement concrete type B0 1:2:4 (using 12.50 mm graded stone aggregate) as in coping benching, gola, slightly rounded and similar items complete all as specified and as directed. 98 M&L for reinforced concrete pipes 150 mm dia, class NP-2, laid and jointed complete with collars complete all as specified. 99 M&L cement concrete 1:3:6 type C-2 for 150 mm dia in bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested etc complete all as specified. 100 S&F SFRC manhole cover 75mm thick factory made with plain surface as per requirement including 75 X1.5 mm flat iron frame all around the cover complete all as specified. 101 Returning, filling in, including spreading, levelling,watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified. 102 Cutting into existing manhole/Sewage line for connecting new drains and making good for 150mm bore pipe and rendering cutting out existing benching and forming branch (1/2 round or ¾ section) channel in plain cement concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregate surface finished even and smooth and reforming benching as required complete all as specified. 103 Removing excavated material to distance not exc50 metre and depositing where directed at a level n.exc 1.5 metre above the starting point complete all as specified and as directed by Engineer-in-Charge 104 M & L for concealed point wiring complete with PVC insulated and unsheathedFRLS cable of 1.5 sqmm (nominal area) with multistranded copper conductor single core 1100 volts grade in and including rigid PVC conduit ISI marked medium grade not less than 20 mm dia,with MS stove enamelled sunkenboxes (normal and modular type as required) including earth dollywith plastic laminated sheet top cover (cover plate with frame in case of modular)of approved make and colour including 1.5 sqmm multistranded FRLS copper conductor cable of green colour as continuous earth wire with lugs and accesseries and making good disturbed surfaces of walls/floor etc complete all as specified anddirected for the followings :- 105 One light / fan point controlled by one way switch 106 One 5 Amp socket outleton independent board. 107 One5 Amp socket outlet on same board. 108 All as per above item No-104 here in before but using 2.5 sqmm single core multi stranded copper conductor PVC insulated and unsheathed,FRLS cable for 15 Amp socket outleton independent board including 2.5 sqmm multi stranded copper conductor cable of green colour as continuous earth wire with lugs etc as required complete all as specified andas directed. 109 S&F socket outlet 6A-2/3 Pin combined 2 module modular type one way 240 volt ISI marked complete all as specified and directed. 110 S&F socket outlet 6A/16A-2/3 pin combined 2 module modular type 240 volt ISI marked complete all as specified and directed. 111 S&F switch 6 amps modular type one module one way 240 volt ISI marked complete all as directed. 112 S&Fswitch 16 amps modular type one module one way 240 volt ISI marked complete all as directed. 113 S & Fofmodular Fan Regulator fan step regulator,120W- single module ISI Marked complete all as specified as as directed. 114 S&F of ceiling rose surface bakelite 63 x50mm three terminals completeall as specified and asdirected. 115 S & Fof sub main wiring with PVC insulated, FRLS unsheathed two single core cable 1100 volts grade with stranded copper conductor of size 2.5 sqmm (Nominal area) drawn in and including PVC conduit of suitable size as directed with and including one run of2.5 sqmm multistranded copper conductorsingle core PVC insulated, unsheathed cable of green colouras continuous earth wire including lugs etcconnected and tested complete all as specified and as directed.Note: (i) Two runs of 2.5sqmm cable and one run of 2.5 sqmm cable of earth continuity conductor and conduit shall be a unit length. 116 S & Fof sub main wiring with PVC insulated, FRLS unsheathed two single core cable 1100 volts grade with stranded copper conductor of size 1.5 sqmm (Nominal area) drawn in and including PVC conduit of suitable size as directed with and including one run of1.5 sqmm multistranded copper conductorsingle core PVC insulated, unsheathed cable of green colouras continuous earth wire including lugs etcconnected and tested complete all as specified and as directed.Note:(i) Two runs of 1.5 sqmm cable and one run of 1.5 sqmm cable of earth continuity conductor and conduit shall be a unit length. 117 S & F sub main wiring with PVC insulated, FRLS unsheathed two single core cable 1100 volts grade with stranded copper conductor of size 4.0 sqmm (Nominal area) drawn in and including concealed PVC conduit of suitable size as directed with and including one run of4.0 sqmm multistranded copper conductorsingle core PVC insulated, unsheathed cable of green colouras continuous earth wire including lugs etcconnected and tested complete all as specified and as directed. Note:(i) Two runs of 4.0 sqmm cable and one run of 4.0 sqmm cable of earth continuity conductor and conduit shall be a unit length. 118 S & F sub main wiring with PVC insulated, FRLS, unsheathed two single core cable 1100 volts grade with stranded copper conductor of size 6.0 sqmm (Nominal area) drawn in and including concealed PVC conduit of suitable size as directedwith and including one run of6.0 sqmm multistranded copper conductorsingle core PVC insulated, unsheathed cable of green colouras continuous earth wire including lugs etcconnected and tested complete all as specified and as directed. Note: (i) Two runs of 6.0 sqmm cable and one run of 6.0sqmm cable of earth continuity conductor and conduit shall be a unit length. 119 S & Fsub main wiring with PVC insulated, FRLS, unsheathed two single core cable 1100 volts grade with stranded copper conductor of size 10.0 sqmm (Nominal area) drawn in and including concealed PVC conduit of suitable size as directedwith and including one run of10.0 sqmm multistranded copper conductorsingle core PVC insulated, unsheathed cable of green colouras continuous earth wire including lugs etcconnected and tested complete all as specified and as directed.Note: (i) Two runs of 10.0 sqmm cable and one run of 10.0sqmm cable of earth continuity conductor and conduit shall be a unit length. 120 S&F sheet metal enclosure double door concealed suitable for SPN distribution boards when MCB to be used having 200 Amp rated bus bar 12 ways 240 V including connection of circuit and submain as per site requirement complete all as specified and as directed . Note- (a) MCBs are to be measured and paid seperately. (b)Make ofMCBs and DB should be same. 121 S&F sheet metal enclosure double door concealed suitable for SPN distribution boards when MCB to be used having 200 Amp rated bus bar 8 ways 240 V including connection of circuit and submain as per site requirement complete all as specified and as directed . Note- (a) MCBs are to be measured and paid seperately. (b)Make ofMCBs and DB should be of same. 122 S&Fsingle pole and neutral enclosure with 2 pin and metal earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and as directed. 123 S&F in replacement of Double door three phasedistribution board4 way IP 43 IK 09loadline VTPN with 125 Amp MCCB to be used as incomer and made out of CRCA sheets 1.6 mm thick,phosphatised powder coated with copper Bus Bar250 Amps, 415 V, Earth Stud, Din Rail, Polymide terminal blocks for incoming and outgoing circuits, inbuilt loose wire box ,ground terminal blocks ,duly prewired with thimbled flame retardant copper conductors and poly layer for protection complete all as specified and directed (Note:-(a) Rate of MCCB and MCBs are included in quoted rate. (b) capacity of Single pole MCB shall be provided as per requirement and direction. (c) Make of MCB /MCCB and DB should be same. 124 S&F MCB SP 6 to 32 Amps,240 volts curve "B",breaking capacity 10KA,all as specified. 125 S&FMCB SPN40 to 63 Amps,240 volts,curve "C", breaking capacity 10 KA, all as specified. 126 Supply and fixingEarthing to DBs with galvanised steel earth plate electrode60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level connected to main earth lead 4.0 sqmm galvanised iron wire by means of bolts, nut, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of MES Schedule pt-I 2009, GI earth lead shall be protected by GI pipe 15 mm dia medium grade and connected to distribution board includingexcavation in any type of soil,returning filling, disposal of soil, providing charcoal dust and common salt upto top edge of earth plate, construction of PCC pit with RCC cover, funnel, watering pipe of 20mm dia GI light grade and provision of earth test point including testing on completion complete all as specified and as directed. 127 M & L for Earth continuity conductor or main earthing lead of 4.0 Sqmm galvanized iron wire, buried in ground or fixed to wall in and including 15 mm bore GI pipe medium grade for protection of earth wire complete all as specified and directed. 128 S&F enviroment friendly,ultra modern,energy saving surface mounted decorative 10 Watt LED bulkhead fitting with pressure die cast aluminium housing ,high efficient LEDs with opal diffuser and IP65 protectio, lumen efficacy 85 lm/watt with colour temerature 6500K, THD≤20 CRI>80,2.5 kV surge protection all as specified and directed. 129 S&Fenviroment friendly indoor decorative 20 Watt LED polycarbonate Batten with opal diffuser , operating voltage range 140v to 270 V, Driver efficiency 88%, lumen efficiency =100 lm/watt , THD≤20 CRI>80 , colour temperature 6500 K, inbuilt surge protection = 2.5 Kv, isolation=3.75, and with zero mercury content including all accessaries all as specified and directed. 130 Supply and fixing LED flat panel fitiing fabricated CRCA sheet steel duly powder coated housing 600 mm x 600 mm, 35/36 watt, 220 V AC recessed/surface type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling glare free opal diffuser PF>0.95 , lumen efficacy>100 lm/W, THD<10% operating range 220v to 240V,CRI>80including connecting up with driver three core flexible copper conductor cases of suitable size and all accessaries all as specified and directed. 131 Supply & fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) with remote complete all as specified and as directed by Engr-in-Charge. Make- Orient/Crompton/Havells 132 Supply & fixBLDC wall mounting fans 230 volts single phase oscillating 400 mm sweep with remote suitable for wall mountingcomplete all as specified and as directed by Engr-in-Charge. 133 supply & fixing plastic body ventilation fan 250 mmas required 50 Hz , 240 volt 1250 RPM with copper wound motor including all fixing accessories complete all as specified and directed.Make- Orient/Crompton/Havells 134 S&F LED bldg light fitting 35/36 Watt, having uniformty ratio 0.25 , high pressure die cast aluminium housing , heat resistant toughened glass frame , IP-65 protection complete with lamp & connected items and connection with suitable cable from celing rose to light fitting and fixing on GI pipe bracket made out of suitable dia GI pipe medium grade 1.2 m long bend to shape and fixed on wall with flat iron clamps nut, bolts washers etc specified and directed 135 Supply and fix cable duct havingsize 45mm wide and 45mm height duly concealed in walls complete all as specified and directed by Engr in charge 136 Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 sq mm 3.5 core 137 Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core 138 Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 25 mm dia suitable for 0.4 mpa working pressure complete all as specified and directed. 139 Excavation in trenches in soft/loose soilnot exceeding 1.5 meter wide & not exc 1.5 mtrdeep and getting out for taking out/laying cable, poles & stay etc complete all as specified and directed by engr-in-charge. 140 Returning, filling in including spreading levelling watering and well ramming in layersnot exceeding 25cm thick after the cable have been laid and tested complete all as specified and directed by Engr-in-Charge.. 141 Removal of excavated surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed by Engr-in-Charge. 142 M & Lfor dry sand cushioning to underground cables with 8cm thick before laying of cables and 15cm thick after laying ( total 23 cm ) and compaction till 18 cm thick for measurement purpose complete all as specified and directed . 143 Material labour for common burnt clay bricks, sub class "B" grade laid in trenches for protection of UG cables perpendicular to the direction of the cables complete all as specified and as directed by Engr-in-Charge 144 Supply and fixingof GI tubing, light grade, 80 mm bore with all fitting laid in trenches / pole / wall for protection of cables in repairs complete. 145 Supply and fixingof GI tubing, light grade, 50 mm bore with all fitting laid in trenches / pole / wall for protection of cables in repairs complete. 146 M&L for tubing medium grade galvanized with all fitting laid in trenches complete of size 25 mm bore complete all as specified and directed. 147 M&L for tubing medium grade galvanized with all fitting laid in trenches complete of size 20 mm bore complete all as specified and directed. 148 M&L for Gun-metal gate valve of size 25 mm with iron wheel head, screwed both ends for iron pipe and fixed. 149 M&L for Gun-metal gate valve of size 20 mm with iron wheel head, screwed both ends for iron pipe and fixed. 150 M&L for construction of brick masonery valve pit of size 60x60x60 cm (internal dimension) with MS top coer of 3mm thick sheet, fixed on frame made out of angle iron 40x40x6mm thick with locking arrangement including two coats of synthetic enamel paint over a coat of red oxide primer to MS sheet internally and externally & iron surface, brick work in cement mortar 1:4, 15mm thick plastering in cement mortar 1:4 (internally & externally) 150 thick plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate for base, 100mm thick PCC 1:2:4 type B-1 using 20mm graded mechanically crushed stone aggregate for coping two coats of white wash internally after preparation the surface complete all as specified and as directed. 151 Excavation in trenches in soft/loose soilnot exceeding 1.5 meter wide & not exc 1.5 mtrdeep and getting out for taking out/laying cable, poles & stay etc complete all as specified and directed by engr-in-charge. 152 Returning, filling in including spreading levelling watering and well ramming in layersnot exceeding 25cm thick after the cable have been laid and tested complete all as specified and directed by Engr-in-Charge.. 153 Removal of excavated surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed by Engr-in-Charge. 154 M&L for cutting GI pipes 80 mm Diafor insertion of new tees,branches connecton for new branch including any tee and necessary accessories complete all as specified and directed.
|
