|
Tender For Additional / Alternator / Modification /Improvement To Mi Room (Building No. P-24) And Certain Minor Works At Af Stn Wadsar Under Ge (Af) Chiloda.; 1 Taking down chowkhats or frames with shutters (with out taking off shutters from the frame) n exc 1.5 sqm each complete all as specified and directed. 2 Taking down chowkhats or frames with shutters (with out taking off shutters from the frame) exc 1.5 sqm but n.exc 4.00 sqm each complete all as specified and directed. 3 Taking down shutters of any description exc 1 sqm and n.exc 2 sqm each complete all as specified and directed. 4 S&F for solid PVC door frame of size 50mm x 47mm made out of 5mm prelam colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specifications & drawings complete all as specified and directed. 5 S&F framed work as in steel doors or gates chowkats of angle or other section withbraces, sheets etc., complete, drilled or welded for MS hinges for fixing of gate or doors other covering andalso fastening and fixing as per site requirements complete all as specified and directed 6 S&F factory made solid PVC moulded door shutter, 28 to 30 mm thick (stiles), with 2,4 or 6 raised panel designed with 2 mm thick moulded PVC sheet on front face and 4mm plain colour PVC sheet on back face as per specification and drawing complete all as specified and directed. 7 M&L for 35 mm thick 2ndclass hardwood glazed and skeleton shutter open rebeted and prepared to receive glass gauze etc(with shash bar) edges of framing plain chamfered or rounded filled with cut and mitered beads for securing, glass etc size of member of shutter as per specified in SSR Part-I section 8,clause 8.24(a) supplyed and fitted to chowkats and directed by Engr-in-Charge. 8 M&L for30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, kiln seasoned and chemically pressed treated complete all as specified and directed by Engineer- in -Charge. 9 M&L aluminium powder coated (powder coated of requried colour) three track sliding windows frame top & sides of size 92x31.75x1.50 mm, bottom size 92x31.75x1.50 mm and shutter top & bottom of size 40x18x1.50 mm and sides (handle) of size 40x18x1.50 mm and lock side shutter frame of size 40x18x1.50 mm with rubber gasket, beading and locking arrangement including making good to the disturbed portion complete including stainless steel wire mesh 0.36mm nominal dia of wire with 1.40mm average aperture and fixed with stainless steel wire staples and fixing 4 mm thick glass with necessary rubber beading gasket etc, one wire mesh shutter and and two nos glass shutter as per drawing No CEAA/STD/01/2010 sheet No 1/1 complete all as specified and as directed by Engr-in-Charge. 10 S&F aluminium ventilator powder coated (requried colour to match window colour), louvers type, frame top & bottom of size 31x42x1.50 mm (rectangular tub of size 40x20x2mm (and middle vertical of size 42x46.20x1.50 mm Section and clip for fixing wire mesh and glass of size 19x17.30x0.90 mm thick including stainless steel wire cloth 0.36mm nomonal dia of wire and 1.40 mm average width of aperture and fixed with stainless steel wire staples and supply and fixing 4 mm thick glass louvers with blades of 100mm heavy duty with necessary rubber beading, gasket etc complete all as specified and directed by Engineer-in-Charge. 11 S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium frame for doors, windows, ventilators & partition etc., with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. 12 S&F Powder coated (thickness of powder coating minimum 50 micron) Anodised aluminium door shutters, aluminium section weighing not less than 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, 3 Nos hinges, tower bolts 2 Nos in each door anodised aluminum snap beading screws etc. complete all as specified complete all as specified and directed.Note :- Wire cloth & Glass pane shall be measured and paid for separately. 13 S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium window and ventilator shutters, side hung without sash bars, aluminium sections weighing 0.55 kg/m & including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21 100mm long (2 No.), suitable handle (1 No), complete all as specified and directed.Note :- Wire cloth & Glass pane shall be measured and paid for separately. 14 Supply, fabricated & fixing Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge. 15 S&F in repairs for 12 mm thick toughned glass as in doors, partitions including hinges, door closer/automatic door closer/floor spring and similar work including cutting to shape, moulding of edge ,etching design where reqd including locking device and SS handles drilling holes required and necessary fitting for fixing the same complete all as specified and as directed. 16 S&F in repair Aluminium (die cast ) body , Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixedcomplete all as specified and directed. 17 S&F in repair Aluminium Mortice lock 4 levers, vertical type, size 100 mm for Aluminium doors complete all as specified and directed. 18 S&F 100 mm long SS butt hinges and fixed to frame with scrwewd or welding / gas welding complete all as specified and directed. 19 S&F for 150mm long aluminium anodized barrel tower bolts of extruded section and fixed complete all as specified and directed. 20 S&F aluminium alloy anodized sliding door bolt with haps and staple (bolt type) and fixing clip of sheet cast or extruted section or cast aluminium alloy and fixed length of bolt 250 mm complete all as specified and directed by Engineer -in -Charge. 21 S&F for 150mm longExtruded aluminium alloy handles, fabricated type, anodisedcomplete all as specified and directed by Engineer-in-Charge. 22 S&F 150mm long Floor door stopper of alunium body and tongue, with hard drawn steel spring, fixed to bottom of door shutter complete all as specified and directed. 23 S&F 300mm size mild steel ordinary rat tail, rod pattern springs including roller and roller plate complete all as specified and directed. 24 Supply only 4 mm thick sheet glass ordinary quality, cut to size as required at site, complete all as specified and directed. (Cost of fixing of glass shall be deemed included in the unit rates under respective items.) 25 S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples orteak wood beading for wooden doors etc complete all as specified and directed. 26 S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples orteak wood beading for wooden doors etc complete all as specified and directed. 27 S&F Aluminium composit panel sheets as in cladding, aluminium doors and partitions etc complete all as specified and directed. 28 M&L for preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. 29 M&L forpainting at old wooden painted surface of any description over 10cm width or grith not otherwise described including preparation , of surface and two coats of synthetic enamel paint complete all as specified and directed. 30 Dismantling plain or corrugated steel sheeting, any gauge, any thickness incl hooks and ridge as retrieved from site complete all as specified and directed. 31 S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering, wall cladding etc, fixed to iron/wooden members with self drilling zincoulium coated metal screws having cap with rubber and metal washers, complete all as specified and directed. 32 S&F in repair 25 mm dia Stainless steel curtain rod with and including two nos of bracket/holders suitable for drapery 25 mm dia rods of one window / door openings complete all as specified and as directed. 33 S&F in repair curtain with blade (vertical venetian blinds) or roller blind, havingroller, threads / Chain & pully system (clutching mechanism) etc complete complete all as specified and as directed. 34 Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed. 35 M&Lfor anodised aluminium snap grid frame work of size (605mm X 605mm ) using T grid/Cross-T/Wall angle/level clip & suspenders for false ceiling and similar works including hangers 6mm dia. G.I. wire (upto 1200 mm length) size of grid (605 mm X 605 mm ) adjusting level fixed to roof slabs/trussesby means of ceiling cleats made out of G.I.flat 40 x 3 mm size 60 mm long and expansion hold fastener 12.5mm dia 40mm longcomplete and supply and fix12 mm thick gypsum tiles (600mm x 600 mm) laminated with PVC film on the face side & metalised polyester film on the back side with all four edges sealed with PVC film fixed complete all as specified and as directed by Engineer-in-Charge. 36 S&F in repiar Soild PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed. 37 S&F 5 mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed. 38 Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc.laid and bedded on pointed on any mortar complete all as specified and directed. 39 M&L for granite work (of any type) 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and directed by Engineer -in -Charge. 40 Dismantling of floor hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles and rubbish off the permises complete all as specified and directed. 41 M&L for 15 mm thick screed bed or bedding layer of morter for laying floor finishes CM 1:6 complete all as specified and directed 42 M&L for vitrified ceramic light coloured tiles 9-10mm thick (square/Rectangular) area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. 43 M&L for non- skid ceramic coloured joint free tiles 7 to 8mm thick (square / Rectangular) area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. 44 M&L glazed ceramic coloured digital tiles 450x300mm x 7mm thick invertical surface etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including backing coat of 10mm thick CM 1:4etc complete all as specified and directed. 45 Demolition of wall of brick and stone wall built in cement mortarincl all quoins, archs, pillars,etc complete all as specified and directed. 46 M&L for Half brick work sub class B bricks, straight or curved on plan to any radius built in half brick thick wallsCM 1:4 complete all as specified and directed. 47 M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m meanradius, built in CM 1:6 complete all as specified and directed. 48 Demolition of cementconcrete (reinforced) of roofs (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge. 49 Excavating in trenches not exc. 1.5 m wide, and not exc. 1.5 m in depth for foundation etc. not exc. 10 sqm on plan and not exc. 1.5 mtr in depth and getting out hard/ dense soil complete all as specified and directed. 50 M&L for PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base, foundation and mass concrete complete all as specified and directed. 51 Returning filling in, including, spreading, levelling, watering and well ramming in layers n. exc. 25 cm complete all as specified and directed. 52 Removing excavated material n. exc. 50 mtr and depositing where directed at a level n. exc. 1.5 mtr above the starting point complete all as specified and directed. 53 M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; verticla or to batter complete all as specified and directed. 54 M&L for re-inforced cement concrete (nominal mix) type B1 (1:2:4) using (20mm graded stone aggregate) inFoundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, underremaed pliles and mass concrete complete all as specified and directed.(Note : Reinforcement shall be measured and paid for separately). 55 M&L for Formwork to sides of pillars, posts, struts, piers,columns, and stanchions complete all as specified and directed. 56 M&L for re-inforced cement concrete (nominal mix) type B1 (1:2:4) using (20mm graded stone aggregate) in Columns, pillars, piers, posts and struts complete all as specified and directed.(Note : Reinforcement shall be measured and paid for separately). 57 M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed. 58 M&L for re-inforced cement concrete (nominal mix) type B1 (1:2:4) using (20mm graded stone aggregate) in roof Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed.(Note : Reinforcement shall be measured and paid for separately). 59 M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work n.exc. 200 mm thick curved ( horizontal orsloping ) with fair finished surfaces for flat roof complete all as specified and directed. 60 M&L for re-inforced cement concrete (nominal mix) type B1 (1:2:4) using (20mm graded stone aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs andd in shelves and the like complete all as specified and directed.(Note : Reinforcement shall be measured and paid for separately). 61 M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, slabs, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to TMT bars complete all as specified and directed. 62 All as per item No 61 here in before but 5mm dia and over up to and including 10 mm dia in stirrups, spaces and binders. 63 M&L for precast reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, shelves and similar articles with plain faces, set in CM 1:4, including necessary form work moulds etc complete all as specified and directed. (Note : Reinforcement shall be measured and paid for separately). 64 Taking down cement or cement lime plaster any description on brick or stone wall/ celling including raking out joint , haking for key scrubing with water etc complete all as specified and directed. 65 M&L for rendering 10 mm thick on fair faces of concrete or brick masonary CM 1:6 finished even and smooth (without using extra cement) complete all as specified and directed. 66 M&L for rendering 15 mm thick on fair faces of concrete or brick masonary CM 1:6 finished even and smooth (without using extra cement) complete all as specified and directed. 67 M&L for rendering 10 mm thick CM 1:6 and setting coat 5 mm thick CM 1:4 finished even and smooth (without using extra cement)in wall including scaffolding complete all as specified and directed. 68 M&L for rendering 5 mm thickin ceiling surfaces.CM 1:4 finished even and smooth (without using extra cement) complete all as specified and directed. 69 Taking out existing unserviceable plaster, loose unsound weaken cement concrete of any description and in any position from existing surface of RCC roof slab/ RCC facia/ beams/ columns/ RCC chajja, average depth 20 mm (approximate 6.5 mtrs height from natural GL) with power driven pneumatic chiesel and removal of debries upto a distence 500 mtrs out side MD land including saw cutting of all edges, making square shoulders of cavaties and roughening of smooth surface, scraping out and removing corrosion and all loose scales, rust etc. from the visible reinforcement and cleaning the steel reinforecement properly providing NIT zink primer, Zink primer on visible reinforcement surface to form a contineous film and preparing the surface to recive concrete of epoxy grouting mortar etc. including providing necessary scaffolding complete all as specified and as directed. 70 M&L for applying bonding coat of modified styrene butadene emulsion in proportion 1 part (bonding agent) : 1 part (water) : 3 part (OP cement) by volume with the brushes etc. to bind new cement plaster/ polymer modified plaster/ concrete/ screed concrete with old surface including removal of loose/ distengrated old concrete/ plaster including preparation of surface etc. complete all as specified and as directed. 71 S&F of wire netting of galvanised steel wire 1.40mm dia with 20mm size of mess fixed with tinned tacks of wire staples complete all as specified and directed. 72 M&L for complete removal of existing treatment of wall surface and applying two or more coats of interior emulsion paint over a coat of primer and 1 mm thick coat ofwall care putty complete all as specified and directed. 73 M&L for preparation ofnew plastered surface of wall and applying two or more coats of interior emulsion paintover a coat of primer and 1 mm thick coat ofwall care putty complete all as specified and directed. 74 M&L for preparation ofnew plastered surface of wall and applying two coats of weather proof acrylic paintover a coat of primer complete all as specified and directed. 75 M&L for complete removal of existing treatment of wall surface and applyiong two coat of weather proof acrylic paint over a coat of primer in old surface of wall and filling cracks with white cement etc complete all as specified and directed. 76 M&L for preparation ofnew plastered surface of ceiling and applying threecoats of white wash complete all as specified and directed. 77 M&L for preparation ofold surface of ceiling and applying two coats of white wash complete all as specified and directed. 78 Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15 cm thickness (below or above G.L) complete all as specified and directed. 79 M&L for 75mm thickCement concrete type B- 1, 1:2:4 (20mm graded aggregate) as in plinth protection and Finishing cementconcrete surface even and fair with brooming and every 2mtr constrction joint to be provided and filled with bitumen with saw dust complete all as secified and directed. 80 M&L for providing 75 mm thick cement concrete 1:4:8 type D-2 (using 40mm graded aggregate) as in sub base complete all as specified and directed 81 Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-25 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. 82 Taking up or down 15mm dia steel tubing and connection including cleaning for refixing or removal to store complete all as specified and directed. 83 Taking up or down 20mm dia steel tubing and connection including cleaning for refixing or removal to store complete all as specified and directed. 84 S&F of 16mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on WALLS / CEILING complete all as specified. supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as specified and directed. 85 S&F of 20mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on WALLS / CEILING complete all as specified. supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as specified and directed. 86 M&L for cuttingchases, in brick walls pinning in, making good to facing where required and pointing in cement mortar 1:3 to endsor edges of andings steps, cills sunshades, shelves lintels etc and cutting chases for concealed water tubingand making good cutting not exc 10 cm grith complete all as specified and directed. 87 Re-fixing old 15mm/20mm dia boresteel water tubing& connection in new or old positionfixed to wall, ceiling or laid in floors including necessary cutting & making of new threads for fixing of new fittings such as elbows, tees, sockets, union, , reducer, etc as required complete all as specified and directed. 88 S&F in repair Fancy type long body CP bib taps15 mm dia, chromium plated cast copper alloy withhalf turn type capstan heads, screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed . 89 S&F in repair Fancy type CP stop/angular cock 15mm dia cast copper alloy, chromium plated fency type screwed down high pressure withhalf turn type capstan heads, screwed both end for iron pipe or for unions and fixed complete all as specified and directed 90 S&F in repair, two way angle valve cock chromium plated fancy type bore 15mm complete all as specified and directed.Make:L & K code No 0327 or techno commercially equivalent as approved by GE. 91 S&F in repairFancy type CP stop valve 15mm dia cast copper alloy, chromium plated fency type with long shank and cup (concealed type)screwed down high pressure with half turn type capstan heads, screwed both end for iron pipe or for unions and fixed complete all as specified and directed 92 S&F in repair 20mm bore stop valve/gate valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed. 93 S&F in repairs vitreous china wash hand basin oval type over /under counter wash basin 560x470mmx 190mm of Ivory colour complete all as specified and directe.Make :Cat part No S2030104 of CERA or techno commercially equivalent as approved by GE. 94 S&F in repairs 15 mm dia pillar tapes Fancy type of Chromoum Platedbrass withhalf turn type capstan heads screwed down high pressure, with or without lettered hot and cold with long shank, screwed shanks and fly nuts, screwed for iron pipes or for WHB complete all as specified and directed. 95 S&F in repairs Viterous China urinals, half stall type (back to corner wall type), complete including providing and fixing plus, beding urinal agianst wall in cement mortar 1:2 securing urinal to plus with and including 60mm long brass screws, pointing aroiund urinal back in cement complete all as specified and directed. 96 S&F in repair PVC waste pipe of 32 mm dia for wash basin/sink complete all as specified and directed. 97 S&F waste coupling of 32 mm dia brass CP forsink/ basins/Urinals, etc with long screwed shanks and fly nuts fanges end bedded in red lead cement and other end fixed complete all as specified and directed. 98 S&F waste coupling of 40 mm dia brass CP forsink/ basins, etc with long screwed shanks and fly nuts fanges end bedded in red lead cement and other end fixed complete all as specified and directed. 99 S&F in repair 125 mm dia Fancy type CP shawer rose complete all as specified and directed by Engineer-in-Charge. 100 S&F in repairs SS soap dish of size 100mm complete all as specified and directed by Engineer-in-Charge. 101 S&F in towel ring of brass CP& including Chromium plated brass screws & wooden / plastic cleats (Minimum weight 90gms) complete all as specified and directed. 102 S&F PVC cabinet with mirror of size 300mmx450mm complete all as specified and directed by Engineer-in-Charge 103 S&F 6.00 mm thick 600 x2000 mm beveled edge mirror of selected quality glass mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. 104 S&F in repairs vitreous china wash down water closet pan pedestal pattern ,white excluding fixing cistern and flush pipe trap front or back inlet including seat cover of any pattern and health faucet (ABS) with rubit cleaning system 1.25 m long, PVC flexible tubeand ABS wall hook complete all as specified and directed. 105 S & F in repair vitreous china squatting pan Orissa pattern of size 580 x 440 mm white with integral foot rest( excluding flushing cistern and flush pipe) squatting pan including connectingto P trap and to flushing pipe complete all as specified and directed. 106 S&F in repair PVC valveless, syphonicaction type flushing cistern, 10 ltr capacity, low level, white, with inlet, ball valve, float and handleincluding bracket, complete all as specified and directed. 107 S&F in repair brass chromium platedtubular towel rail 20 mm dia D type 60 cm long including brackets/flanges complete all as specified and directed. 108 S&F PVC water connection 450 mm long to wash basin of 15mm dia including CP nuts and washers complete all as specified and directed by Engineer-in-Charge.. 109 Supply and fixing in repair toilet paper holder chromium plated as per sample appproved by GE. 110 S & F mild steel chromium plated grating doom 100mm dia with or without hole complete all as specified and directed. 111 S&F in repair double bowl sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 1143mm x 508mm x 228mm bowl size 508mm x 406mm complete all as specified and directed. 112 S&F in repairs for solid PVC kitchen cabinets/cupboards frame/shuttersmade with 16-18 mm thick Wooden plastic composit (WPC) boards one side laminated and other side white complete all as specified and as directed by Engineer-in-Charge. 113 S&F CP decorative type SS handles 75mm long fixed to PVC sheet or frame complete all as specified and directed. 114 S&F magnetic and connected plate to shutter and frame as per sample complete all as specified and directed. 115 S & Fauto close hinges, stainless steel, bright finish or electro galvanised fixed complete all as specified and directed. 116 Removing of existing unserviceable water proofing treatment including PCC tiles (except PCC padding) taking down cement plaster etc, of any description and cleaning of top surface of cement concrete flushing out junction of parapet walls & washing down with water to remove all dirt etc including preparation of surfaces to receive new treatment and removing the rubbish off premises out side MD land complete all as specified and directed. 117 Dismantling of un-reinforcement lime concrete/cement concrete in padding to roof slab and removing the rubbish off premisesout side MD land complete all as specified and directed. 118 M&L for providing cement concrete type B-0, 1:2:4 using 12.50mm graded aggregate laid to slope in padding for WPT over roof slab complete all as specified and directed by Engineer-in-Charge. 119 M&L forrendering10mm thick in CM 1:4,mixed with WPC @3% by weight of cementon fair faces of concrete surfaces without using extra cementas in roof complete all as specified and directed.Note:- WPC shall be measured & paid separately. 120 M&L for preparing clean and dried plastered surface and applying a coat of oil basedbitumen primer conforming to IS 3384-1986 @ 0.30 litrs/sqmand then laying APP polymer modified membrane 3.5mm thick with non woven polyster reinforced membrane (min 3.50 kg/sqm) having thermal insulation with white mineral gravel finish on upper side of membrane and laid by torch application method to the entire surface complete all as specified and directed by Engineer in Charge. 121 Supply only intergral water proofing compound. 122 Dismantling water tanks and exc. 500 but not exc. 1000 litre capacity complete all as specified and as directed. 123 S&F rotational moulded water storage tank 750ltr capacity double layer (cylindrical vertical with closed top) white colour hoisted and fixed in position complete all as specified and as directed. 124 S&F 20mm dia (min weight 210 gms) PVC ball valves high pressure of PTMT withepoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and directed. 125 S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, frame work for cooler stands , water tank cagings , angle iron frame works , steel ladders , vertical posts , balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. 126 S&F Welded steel wire fabric to steel members of weight not exceeding 4 kg per sqm complete all as specified and directed. 127 S&F 125mm long heavy weight cold rolled mild steel hinges and fixed to frame with screwed or welding complete all as specified and directed. 128 M&L painting to new steel surface of any description over 10cm width or grith not otherwise described including preparation , priming with zinc chromateand two coats of synthetic enamel paint complete all as specified and directed. 129 M&L painting to old steel surface of any description over 10cm width or grith not otherwise describedand applying two coats of synthetic enamel paint complete all as specified and directed. 130 Taking down PVC pipe (SWR) 110mm dia bore and connection complete all as specified and directed. 131 S&F 110 mm dia bore pipe (SWR) single socket in any length rubber joints fixed to wall. or laid in floors etc complete all as specified and directed. 132 S&F 110mm borePVC (SWR) bends any radius with access door complete all as specified and directed. 133 S&F 110mm borePVC (SWR) junction single, (single T) equal or unequal any radius with acess door complete all as specified and directed. 134 S&F 110mm borePVC (SWR) cowl any radius complete all as specified and directed. 135 S & F Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof for 110 mm bore pipes complete all as specified and directed. 136 Demolition and breaking up drain pipes, 200 mm internal dia (Salt glazed stoneware, AC or reinforced concrete) (internal dia) set in cement mortar including haunching and bed concrete complete all as specified and directed. 137 M&L for cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in bed to drain pipes of size 200 mm bore, including packing under & haunching against the sides of pipes after they are laid and tested complete all as specified and directed. 138 M&L forRCC NP2 class drain pipes of 200 mm internal dia, laid to slope in trenches, jointed in CM 1:1 and tested complete all as specified and as directed. 139 M&L for cutting into existing manholes for connecting new drains of 150/200 mm internal dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel ( ½ roundor3/4Section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete all as specified and directed. 140 Surface excavation n.exc. 30 cm deep and averaging 15 cm deep and getting out in hard dense soil complete all as specified and directed. 141 M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizintal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed. 142 M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4, over RCC roof slabs for laying water proofing treatment mixed with using water proofing liquid @ 150 ml per bag of cement complete all as specified and directed by Engineer-in-Charge.(Note : Water proofing liquid shall be measured and paid separately) 143 Supply for integral liquid water proofing compound 144 Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm of make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufacturedby M/S IWL Ltd or ‘Shaliplas’ (polyester) manufactured by M/S Capital Steels and chemicals Pvt Ltd as approved by GE, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or ‘EMW FLATE’ of M/S Texas India Ltd}at the rate of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructionscomplete all as specified and as directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, applied@1.20 Kg/Sqm over a coat of bituminous primer confirming to IS-3384 applied @ 0.40 Kg/Sqm(ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii)The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv)In case of stone masonry parapet wall etc a groove of size 25mmx25mm(minimuim) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimny/other vertical surfaces and polimeric membrane insterted in groove and sealed with paving bitumen (v) Exposed surfaces of APP membrane shall be applied with one coat of bituminous aluminium paint @ 150 ml/Sqm. (vi) Above aspects are deemed to be included in quoted rate. 145 M&L for rendering 15 mm thick on fair faces of brick work on concrete surfacs in CM (1:4) on external brick / concrete surface finished even and smooth without using extra cement complete all as specified and directed. 146 M&L for rendering 5 mm thick on fair faces of brick work on concrete surfacs in CM (1:3) on ceilingsurface finished even and smooth without using extra cement complete all as specified and directed. 147 M&L for Hard core of gauge broken stone or bouldersn.exc.63 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed. 148 M&L 40 mm thickPCC (1:2:4) type B1 using 20mm graded agg as in floors complete all as specified and directed. 149 M & L PCC1:3:6 type C-2 using 40 mm thick graded agg using Plinth Protection 75 mm thick complete all as specified and directed. 150 M & L forming construction joint 30 mm deep x 10 mm wide filled with sealing compound grade A complete all as specified and directed. 151 M&L for preparation of newly plastered surfaces of walls and applying two coat of cement base paint complete all as specified and directed. 152 M&L for preparation of newly plastered surfaces and applying three coat of white wash on wall complete all as specified and directed. 153 Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed. 154 M&L for cement concrete Type C2 1:3:6 (40mm graded aggregate) as in foundations, filling and mass concrete complete all as specified and directed. 155 S&F Framed Steel work in tubular section for purlin, rafter, posts and similar items including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and as directed. 156 Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. 157 M&L for re-inforced cement concrete (nominal mix) type B1 (1:2:4) using (20mm graded stone aggregate) in Chajjas complete all as specified and directed. 158 M&L for PCC (1:5:10) type E2 using 40mm graded agg as in sub base complete all as specified and directed. 159 S&F mild steel framed work as in window/ventilator guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding complete all as specified and directed. 160 S&Ffor steel windows/ventilators conforming to IS-1038 with side hung shutters including projected type hinges with 2 Nos MS 100mm size tower bolt over MS flat iron for each openable leaf & Z section handle and steel peg stay complete without glazing bars, dovetailed or welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed by Engineer-in-Charge.(Note :- Wire clothshall be measured and paid for separately). 161 M&L Machine pressed precast concrete interlocking paver block With grey cement and no pigments any shape and size confirming to IS 15658 -2006 of 60 mm thickness, M-35 Grade complete all as specified and directed. 162 M&L Sand filling under floors or in foundationincluding watering and consolidation complete all as specified and directed. 163 M&L for precast (factory casted) cement Concrete kerb stone casted in PCC (1:2:4) type B-1 using20mm graded stone aggregate with plain or interlocking joints (as directed),making groove in ground of desired dimension, placing in erect position Kerb stone in edging and set and jointed in cement mortar 1:4, making good distrubed surface of ground complete all as specified and directed. 164 M&L 25mm thick PCC 1:2:4 type B-0 (12.5 mm graded aggregate) as in levelling course complete all as specified and directed. 165 M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 as in backing coat for tiles complete all as specified and directed. 166 M&L for Acid resistant tiles 15mm thick vitreous ceramic, unglazed, set, jointed and pointed in chemical resistant mortar, resin type, in floors/vertical surfacescomplete all as specified and directed by Engineer-in-Charge. 167 M&L for complete removal of existing treatment from old wall surfaces and applying two coats of oil bound distemper over required coat of wall putty as in repairs complete all as specified and directed. 168 M & L for concealed point wiring complete with PVC insulated /unsheathed strandedcopper conductor of wire 1.5 Sqmm , 1100volt grade FRLS , alongwith one single core ofsame size stranded copper as continuousearth wire to common earth dolly in andincluding PVC conduit pipe fitting medium grade suitable size fixed in concealed surface of wall/ceilling/false ceilling including cutting /chasing in wall asrequired with powder coated sheet metal terminal boxes of required sizes and thickness (factory made) sunk in wall onlywith 3.0mm thick laminated sheet where asrequired and accessories complete incl taking down old us point suitable for the following :-(a) One light/fan point controlled by one onway switch 169 All as per item No 168 here in before but One socket outlet 05 Amps on the same board 170 All as per item No 168 here in before but One socket outlet 05 Amps on independent board 171 All as per item No 168 here in before but point wiring with 2.5 Sqmm cable and 2.5 Sqmm earth continuity conductor for 3 pin 15 Amp socket. 172 S&FSwitch piano, single pole one way 5 Amps 240 volt capacity flush type complete all as specified and directed. 173 S&F 3 pin 5 Amps Socket outlet, flush type complete all as specified and directed. 174 S&F 5 pin, 5 Amps switch & socket combination flush type multipurpose3 pin, 5 Amp flush type universal complete all as specified and directed. 175 Supply and fix 3 pin 15 Amps switch socket combination, flush type multi purpose 2 in 1 type (3 pin 5 Amps and 15 Amps) complete all as specified and directed. 176 S&FSwitch piano, single pole one way 15 Amps 240 volt capacity flush type complete all as specified and directed. 177 S&F 6 pin 15 Amps Socket outlet , flush type complete all as specified and directed. 178 S&F fan regulator electronic step type 230 volts switch type suitable for any type of ceiling fan sweep complete all as specified and directed. 179 S& F ceiling rose with cover plate, 5 Amps surface type 240 volts bakelite three terminal complete all as specified and directed. 180 S&F in replacement 4 way sheet metal enclosures for flush/surface mounting distribution board double door, 240 volts factory made and tested complete, suitable for mounting MCBs with 200 Amps rated bus bar, cable lugs complete all as specified and directed 181 S&F in replacement 8 way sheet metal enclosures for flush/surface mounting distribution board double door, 240 volts factory made and tested complete, suitable for mounting MCBs with 200 Amps rated bus bar, cable lugs complete all as specified and directed 182 Supply and fixing amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of SP 5 To 32 AMP current carrying capacity in the MCBDB complete with connection testing and commissioning complete all as specified and directed 183 All as per item No 182 here in before but SPN 40 to 63 AMP 184 S & Fin repairs of LED batten fitting alongwith removable LED Tube 20W, 230 Volt,wall /ceiling mounted ,LED battenfixed by means of bolts,ABS rotor suitable for single side connections. LED rod having glass material complete haivng lumen efficacy minimum 100 lm/w,CCT 6500 K, CRI>80 ,burning hour minimum 25000,PF - 0.9 powered by integral constant current driver suitable for 230 V AC with all accessories internallly prewired including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. 185 Supply and fixing in repairsLED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type100 lm/w,CCT 6500 K, CRI>80 ,burning hour minimum 25000, PF - 0.9, with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 186 S&F Detectors Complying with and type certified to EN - 45 Addressable type multisensor detector with heat and smoke combination Photoelectric /Opticalwith base with self built intelligence as per IS: 11360 fixed at location as per direction of Engineer-in-charge 187 S&F Fire Alarm Sounders / Sirens Electronic type horizontal single stage continous normal operation for atleast 50 minutes with sound level 65 DB to 120 DB measured at 1.5 Mtr with sound output variation of + 5 DB 500 mtrs range fixed at location as per direction of Engineer-in-charge. 188 S&F Fire alarm control panel complying with BS EN 54 Single loop panel of capacity from 30 detectors & 30 modules Supply, installation, testing & commissioningof AddressableControl Panel 40 device/2 ZoneMicroprocessor basedAddressable Main Fire Alarm digital display panelInput AC power supply, automatic battery charger,display panelInput AC power supply, automatic battery charger12 volts sealed maintenance free lead acid batteries sufficient for 8 hours normal working and capable of operating the system for 60 minutes during emergency conditions, complete with log facility complete all as specified and directed 189 S & Fof Manual call point for fire alarm system incl all commissining and testing complete all as per dreiction of Engineer in charge. 190 M & L for circuit/submain wiring alongwith earth wire with thesizes of FRLS is PVC insulated copper conductor, single core cable in surface/recessed as required 2x1.5 sq. mm + 1x1.5 sq. mm earth wire in steel conduit for connection of Fire smoke detector from control panel and fire alarm sound detection system as per site requirement and as per dreiction of Engineer in charge. 191 Supply and fixing in replacement LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type complete all as specified and directed 192 Supply & fix Air Circulator fans 230 volts single phase 400 mm sweep suitable for wall mounting Incl all electrical connection complete all as specified and as directed. 193 Supply and fix exhaust fan made of sturdy Engineering plastic with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep upto 250 mmcomplete all as specified and directed. 194 Supply, install,commissioning and testingInvertor type 5 star rated air cooled split unit air conditioner electric driven single phase of capacity of 1.5 TR, Eco friendly refrigerant, hi wall split units indoor/outdoor unit complete with cordless remote control unit andauto restart facility, 100 % copper and stabilizer free operation, includingexcess copper tubing if required beyond the length supplied with AC unit and PVC conduit of 15mm dia not exceeding 2.5 mtr long for water drain and making good to disturbed surface with cement mortar ratio of 1:3 and testing complete all as specified and directed by Engineer-in-charge. Note:- (i) Rate quoted for items includes cost of all civil work like cutting to wall ceiling, floor, filling with PCC,finishing the surfaces with existing to match etc, if required for installation of AC unit as directed. (ii) Required copper pipes for installtion shall be deemed to be included in the quoted rates 195 M&L for concealed sub main wiring of two run with 4.0 Sqmm single core PVC insulated, FRLSflexible multi stranded copper conductor cable 1100 volts grade, drawn through and including PVC conduit and accessories of suitable size and fixed on concealed surface of wall/ceiling with cutting chases where required including one run of 4.0Sqmm single core PVC insulated, FRLS,flexible copper cable as earth continuity conductor in green color complete all as specified and directed. 196 S& F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and directed 197 Supply and install water dispenser electric driven single phase havingcooling capacity 2.5 ltr/hr & heating capacity 2.5 ltr/hr having storage capacity 2.5 ltr each for hot and cold water complete all as specified and directed 198 Supply, installation, commissioning of Water cooler fully stainless steel, electric driven single phasehavingstorage capacity of 80 Ltrs and nominal cooling capacity of 40 ltr per hour incl all electrical connection complete all as specified and directed.
|
