|
Tender For Renovation Of Wildlife Research Lab In Department Of Zoology At Main Campus U.O.K (Advertised Cost Rs. 5.62 Lac)- 1 Providing and laying in position specified grade of reinforced cement concrete including the cost of centering, shuttering, finishing and reinforcement all work up to all levels. 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) Crushed 2 Half brick masonry with bricks of class designation 75 in superstructure up to all floor levels. In cement mortar 1cement: 4 fine sand mortar 3 12mm thick cement plaster on half brick/ concrete wall of mix 1:6 (1 Cement: 6 Coarse sand) 4 Demolishing cement concrete work, including disposal of unserviceable material within the campus as per directions of EIC 1:3:6 or richer mix 5 Flooring/tile work. Cement concrete flooring 1:2:4 (1Cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry but excluding cost of nosing of steps etc. complete. 50 mm thick 20mm nominal size stone aggregate (crushed) 6 Steel WorkReinforcement for RCC works including straightening, cutting, bending placing in position and binding all complete up to all floors. Thermo mechanically heated bars. 7 Providing and fixing Tiled/GRID false ceiling of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paintpaint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in plain Tegular edge Global white/Off white colour tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending 8 Providing and laying anti-skid vitrified floor tiles of size 600x600mm (thickness to be specified by the manufacturer) approved make in all colors, shades as approved by engineer- in-charge laid on 20mm thick bed of cement mortar 1:4 (1cement: 4 coarse sand) including pointing the joints with matching pigment or any other relevant pigment as directed including cleaning the floor after finishing of work including 5mm-6mm spacers (Sample to be approved by EIC) 9 Providing and fiixing wpvc lowers/ fluted panelling of approved thickness including all related accessories like corner/ top flashing etc complete including grounds, including fixing, screwing complete 10 Providing and fabrication of ward robes (ornamental) of approved quality 19mm Ply board in sides, shelves and wherever required including 6mm ply wood on back and 19MM ply board in shutters, inside and outside of shutters finished with Dulmica sheeting of approved quality and color on exposed face of approved design and drawings including (painting two or more coats of synthetic enamel paint of approved quality and color inside) including cost of following aluminum fittings and locks of approved make.15mm dia. M.S. pipe chromium plated with necessary brackets 4"-0" length and including all other necessary accessories complete in all respects. Including fixing with dashfasteners wherever required (For payments front face to be measured).40-45 cm deep 11 Providing and fixing Salem stainless steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. 610x510mm bowl depth 200mm. (Sample to be approved by EIC) 12 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain Polypropylene random fittings, (including necessary PPR reducers) etc. This includes testing of joints complete as per direction of Engineer incharge.Internal work Concealed fixing the pipe etc. (Sample to be approved by the EIC)25mm 13 Providing and fixing of PVC pipe (Type "B") in proper gradient in excavated trenches including jointing and refilling the excavated material complete including cost of excavation. (Sample to be approved by EIC)75mm 14 Painting with synthetic enamel paint of approved brand and manufacture of required color to give an even shade .one or more coats on old wood/plaster work. 15 Proviidng and fixing of following Sanitary PPR fittings 16 Sink Mixer 17 C.P waste along with flexible pipe 18 Floor Trap 75mm with grating 19 Union 25mm 20 Ball Valve 25mm 21 Providing and fixing 18mm thick mirror polished, machine cut for floors, kitchen platform, vanity counters facieses and other similar locations of required size of approved shades, color and texture laid over 20mm thick base cement mortar 1:4 (1cement: 4 coarse sand) and joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing etc. including moulding on outer edges complete at all levels. Black or as approved by EIC Please Enable Macros to View BoQ information 22 Providing and fixing 18mm thick mirror polished, machine cut for floors, kitchen platform, vanity counters facieses and other similar locations of required size of approved shades, color and texture laid over 20mm thick base cement mortar 1:4 (1cement: 4 coarse sand) and joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing etc. including moulding on outer edges complete at all levels. Black or as approved by EIC Please Enable Macros to View BoQ information
|
