|
Tender For Certain B R Maintenance Repair Work To Offrs Jcos Or Md accommodation At Sunderbani Ge N Akhnoor- 1 Taking down existing old treatment incl padding water proofing plaster of any descriptionany type, roof tiles cement mortar screed bed and removing existing bitumen felt treatment incl brushing, brooming, cleaning top surfaces of roof slab to receive plaster etc incl disposing off debris from MoD land complete all as specified and directed. 2 Rendering 15mm thick in cement mortar(1:3) with water proofing compound onfair finishes of brick work or concrete surface of roof slab, to be finished even and smooth(without using extra cement ) all as specified and directed.( Water proof compound shall be measured and paid separately) 3 Roof treatment :-Water proofing treatment to RCC roof slab including parapet as under :- (a) Ist Course: Apply a coat of bituminous primer conforming to IS-3384@ 0.40 Kg /Sqm on prepared surface of plaster and after drying of primer, apply a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.2 Kg/sqm on plastered surfaces. (b) 2nd Course :APP (Atactic Polypropylene) modified polymeric membrane, 5 layered,3 mm thick weight not less than 3.0 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 150 mm end overlap, membrane has to be laid with LPG torch and overlap sealed and finished neat, all joints.(c) 3rd Course : Apply a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.2 Kg/sqm over membrane and dusted with dry sand @ 0.50 to 1 Kg/sqm. Note : Roof treatment shall be carried out through approved manufacturers or their authorized personal only. 4 Sunken Floor treatment :-Providing and laying of water proofing treatment to sunken portion including vertical portion by applying cement slurry mixed with acrylic based polymer modified cementitious composite compound of make as specified and approved including demolition and filling of sunken floor with & including PCC 1:5:10 type E-2 (using 40mm brick aggregate).(a) First layer of slurry of cement @0.488 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.253 Kg/Sqm. This layer allowed to air cure for 4 Hours.(b) Second layer of slurry of cement @0.242 kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.125 Kg/Sqm. This layer allowed to air cure for 4 Hours.(c) 15mm thick plaster in CM 1:3 mixed with WP compound to be provided while concrete is still green.(d) Joint of/Trap/WC/Soil pipes shall be properly sealed with sealing compound.Note:(a) Concrete for sunken slabs shall be mixed with WP compounds as per manufacturer"s instructions. Before carrying out water proofing treatment the sunken slab shall be tested with water for 48 hours for any leakage /dampness is seen in ceiling below, then treatment is again carried out to RCC slab and it is again tested before passing for next stage. (The rate quoted includes water proofing compound as per manufacturers instructions).(b) Please note that only floor area shall be measured for payment purpose. 5 Preparation of new or previously untreated surface of concrete or surfaces of any description and applying two coats of aluminium paint over roof surfaces over 10cm width or girth not otherwise described, all as specified and directed. 6 Taking down chowkats or framesexceeding 1.5 Sqm and n.exc 4.00 sqm each with shutters (without taking off shutters from the frames) all as specified and directed. 7 Taking down chowkats or framesnot exceeding 1.5 Sqmwith shutters (without taking off shutters from the frames) all as specified and directed. 8 Taking down shutterof any description area exc 1 sqm but not exc 2.0 sqm each complete all as specified and directed. 9 Plain Cement Concrete 1:3:6 type C-0(using 12.5 mm graded crushed stone aggregate) as in filling of pressed steel chowkats, roof kerbs, parapets, copings, holdfasts including use and waste of formwork as applicable complete all as specified and directed. 10 Pressed steel frames for doors with one or more rebates of size 125x60mm including necessary fixing lugs, hinges, lock strike plates complete, providing mild steel 6 mm dia thresh hold bar complete all as specified and as directed. 11 Pressed steel frames for doors with one or more rebates of size 105x60mm including necessary fixing lugs, hinges, lock strike plates with mild steel 6 mm dia thresh hold bar complete all as specified and as directed. 12 Solid PVC (Door/almirah/cupboard) frames of size 50 x 47mm made out of 5mm dia plain colour PVC Sheet reinforced with MS Square tube, supplying and fixing in opening as per specification and drawing all as specified. 13 35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated, complete all as specified. 14 Glazed and skeleton shutters 30 mm thick second class hard wood, opened rebated and prepared to receive wire mesh etc, edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing witre mesh etc. Size of members of shutters as specified in SSR Part-I, Sec-8, clause 8.24(a), complete all asspecified and directed. 15 Factory made solid panel PVC door incl Almirah / Kitchen Cupboard / (wooden texture) shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top and bottom rails. M.S frame shall be covered with heat channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as a gap insert for top rail and bottom rail; Panelling of plain colourPVC sheet to be fitted in the M.S frame welded / sealed to the stiles and nails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at side as per specification and drawings.Note : The external surface area of almirah/kitchen cupboards shall only be considered for payment and the contractor shall quote rate accordingly. 16 Prelaminated particle board 18/19 thick, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and directed. 17 External teak wood lipping 6 mm thick fixed with nails for 18/19 mm thick board, complete all as specified. 18 S&F in replacement of Kitchen cabinets of PVC Solid board(wooden texture) size 900mmx750mmx600mm, including partitions, shelves and drawers with brass sliding rails,channels,door handles, door catchers, overall cabinet internally and externally madewith both side PVC laminated termite proof board, 18/19 mm thick, ISI marked including PVC kitchen/cup board frame of size 18mmx63mm made out of 18mm thick PVC pre-laminated ply coloured and frame shall be fixed with 50mm long steel screw inside using drilling machine and plastic fasteners, having following specifications:.....Contd to Srl item No 18.01 19 (i)Outer frame made six 50mmx47mm with same board.(ii)Shutters both side PVC laminated termite proof board, 18/19 mm thick having stainless steel soft closing concealed hinges with one No brass handle of 75mm including brass door catcher of not less than 50mm size in each shutter.(iii) Drawers made of both side PVC laminated termite proof board, 18/19 mm thick including brass handles of front and two sliding rails at sides in each drawer.(iv) All cabinets, drawers, frames, partitions and boards shall be fixed at site with brass machine screws and PVC plugs of suitable sizes. Note:(a) Only front face dimensions at site (Length and Height), shall be measured and entered in MB irrespective of Nos of partitions or drawers. Cost of all partitions as required at site shall also be deemed to have included in quoted rates and nothing extra is admissible on this account. (b) Different No of partitions and drawers may be as per site requirement with out any extra cost.(c) All labours and materials cost shall be deemed included in quoted rate. 20 300mm Mild steel ordinary rat tail rod pattern springs including roller and roller plate fixed, complete all as specified. 21 Powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. 22 Powder coated aluminium anodised door shutters(minimum thickness of powder coating 50 micron), aluminium section weighing 0.55 kg/m includingnecessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed. 23 Powder coated anodised aluminium window / ventilator( glazed / gauged skeleton shutter ), (minimum thickness of powder coating 50 micron), side hung type without sash bars, aluminium sections weighing 0.55 kg/m includingnecessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinges type B-21 100mm long (2 No. ) suitable handle (1 No.) Glass shall be measured and paid separetely under relevant item of BOQ complete all as specified and as directed. 24 Door closer hydraulically regulated, aluminium extruded section body designation No. 1, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed in repairs complete all as specified and as directed. 25 Anodised aluminum grill (Anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with CP brass/stainless screws @200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and directed. 26 5.5 mm thick tinted sheet glass, selectedquality and glazing with aluminium beads and rubber packing in square not exceeding 0.5 square metre in each pane, complete all as specified and as directed. 27 5.5 mm thick tinted sheet glass, selectedquality and glazing with aluminium beads and rubber packing in squareexceeding 0.5 square metre in each pane, complete all as specified and as directed. 28 Galvanised mild steel wire cloth 0.36 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed 29 100 mmbutt hinges, medium weight cold rolled mild steel, complete all asspecified and directed. 30 Aluminium handle cast type anodised of size 150mm ;long ISI marked complete all as specified and directed. 31 Aluminium anodised barrel tower bolt 150mm extruded section ISI marked complete all as specified and directed. 32 300mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified and as directed. 33 Steel windows/ventilator (Box type) factory made with double shutter with or without devetailed bar ( glass & glazed shutter) of size 79mmx39mm,16 gauge rectangular tubular frame withside hung shutter with glazing bars 12x3mm flat iron incl box type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts in each shutter 100mm long with & including 8mm square bar grills, complete all as specified & as shown on drg No. CEUZ/TD/1269/2008 Sh No 1/1 to 1/3 .Note:-(a) Fixed type glass panes shutter if any provided in above same window shall be measured and paid separately & area of these fixed shutter shall be deducted from total area of box type window for payment purpose. (b) Sheet glass/ wire cloth shall be measured & paid separately under respective item 34 Steel Windows/ventilator (Box type) factory made without glazing bars shuttersonlycomplete all as specified& as shown on drg No CEUZ/TD/1269/2008 Sh No 1/1/ to 1/3. 35 Galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified. 36 S&F in repair Galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified. 37 Hacking out old broken glass (any thickness, size, quality or description) from metal frames/Aluminium framesincluding punching or drilling out old glazing pins/spring clips complete all as specified and as directed. 38 Glazing with sheet glass 3 mm thick, ordinary quality and glazing with oil putty and glazing pins in squares not exceeding 0.5 Sqm in each pane, complete all as specified and directed. 39 Figured glass sheet, 3 mm thick, ordinary quality and glazing with oil putty and glazing pins in squares not exceeding 0.5 Sqm in each pane, complete all as specified and directed. 40 Floor door stopper 150mm overall length of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed at bottom rail of door including taking down old u/s one all as specified and directed. 41 Preparation new steel and iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer, complete all as specified and as directed. 42 Preparation of new untreated wood and wood based surfaces of any description over 10cm in width or girth not otherwise described and painting with two coats of synthetic enamel paint over a coat of pink primer,complete all as specified and directed. 43 Curtain rod ,20 mm dia Stainless steel ,chromium platedfixed with CP bracket, incl taking down of old curtain rods, complete all as specified and directed. 44 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises,complete all as specified and directed. 45 Demolition of cement concrete(unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or aboveground level) complete all as specified and as directed. 46 PCC 1:2:4 type B-0, (using 12.5mm graded crushed stoneaggregate) 25mm thick as in subbase to floors all as specified and directed. 47 Nonskid coloured ceramic tiles 7mm to 8mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm as in floors etc,set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfacesincl 15mm thick screed bed/bedding layers in cement and sand mortar 1:4 all as specified and directed. 48 Nonskid coloured ceramic tiles 7mm to 8mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm as in dado/skirting etc,set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfacesincluding 10mm thick rendering in cement and sand mortar 1:4 finishes even and rough complete all as specified and directed. 49 Vitrified ceramic coloured tiles (light shade) 10mm thick (Square/reactangular) area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed neat cement slurry and pointed in white or coloured cement to match Screed bed or bedding layer 15 mm thick for laying floor finishes in CM 1:4 complete all as specified and directed. 50 Vitrified ceramic coloured tiles (light shade) 10mm thick (Square/reactangular) area of each tiles not exceeding 0.36 sqm, in skirting etc set and jointed neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement and sand mortar 1:4 complete all as specified and directed. 51 Glazed ceramic coloured tiles 450x350x7mm thick on vertical surfaces such as skirting, dados and risers to steps etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10mm thick rendering in CM 1:4 finished even and fair to receive tiles, complete all as specified and directed. 52 20mm thick granite work (table rubbed and polished) as in steps, jambs, pillars, cooking platform etc, bedded and jointed in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixure of pigment to match with shade of granite including 15mm thick screed bed in CM 1:4 after applying cement slurry @3Kg/Sqm incl provision of hole for gas pipe complete all as specified and directed. 53 Taking down cement plaster of any description including raking outjoints, hacking for key, scrubbing down with water etccomplete all as specified and directed. 54 Rendering 15mm thick cement plaster with cement mortar(1:4) on fair faces of brickwork or concrete surfacesand finished even and smooth without using extra cement complete all as specified and directed. 55 Rendering 10mm thick cement plaster with cement mortar (1:6) on other than fair faces of brickwork or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed. 56 Rendering 05 mm thick in cement and sand mortar 1:3 on ceilings including finishing the surface even and smooth without using extra cementcomplete all as specified and as directed. 57 Demolition of brick work built in cement mortar including all quions, arches, pillars etc. all as specified and directed. 58 Brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified and directed. 59 Brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, but except bricks all as specified and directed. 60 Walling of random rubble uncoursed, well bonded, bedded and solidly hearted built in CM 1:4 complete all as specified and directed. 61 Ditto as per item no. 59, above but except stone set set in 1:4 complete all as specified and as directed. 62 Raised pointing to random rubble, uncoursed or brought upto course masonry in CM 1:4 complete all as specified and directed. 63 Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 40mm to face stones (lime and sand stone) and dressing of face beds and joints, complete all as specified and directed. 64 Preparation of newly plastered surfaces of walls andapplying two coats of oil bound distemper over a coat of chalk whitening primer complete all as specified and as directed. 65 Preparatrion of newplastered and unplastered surfaces of walls and applying two coat of cement based paint over alkali resistant priming paint all as speicfied and directed. 66 Preparation of newly plastered surfaces of ceiling andapplying two coats of oil bound distemper over a coat of chalk whitening primer complete all as specified and as directed. 67 Repair to balcony/Facia/Roof projections and soffit of chajjas etc by taking down old rendering and hacking clearly the edges and corners smooth rounded for new plastered area exceeding 30sqm in width or girth & providing 15 to 20mm thick plastering to match with the existing thickness in CM 1:3andincluding formwork up to height 7.0 mtr above ground level of bldg including two coats of Apex/cement based paint over one coat of primer complete all as specified and directed. 68 Preparation of old plastered and unplasteredsurfaces of wall and applying two coat of oil bound distemper on walls, complete all as specified. 69 Preparation of old painted surfaces by washing, rubbing down and stopping of distempered and painted walls and applying one coat of oil bound distemper complete all as specified and as directed. 70 Preparation of old painted surfaces and applying one coat of oil bound distemper on ceiling complete all as specified and as directed. 71 Preparation of old painted surfaces by washing, rubbing down and applying one coat of cement base paint complete all as specified and as directed. 72 Applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm on wall surface, complete all as specified and directed.Note:-(i) The work shall be carried out in different shade and the same shall be got approved from Engineer-in-charge/GE/(ii) The work shall be carried out upto 4th storey of bldgs and no extra payment shall be admissible for necessary form work & scaffolding required for the same. 73 Preparation of old steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and painting with one coat of synthetic enamel paint all as specified and directed. 74 Preparation ofold wooden surfaces of any descriptionexc 10 cm width or girth, and applying one coat of synthetic enamel paint complete all as specified and directed. 75 Cleaning and removing all scale and dirt etc from 500 ltrs water tanks and from mouths of circulating pipes etc., complete all as specified and directed. 76 Cleaning and removing all scale and dirt etc from 1000 ltrs water tanks and from mouths of circulating pipes etc., complete all as specified. 77 Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) 03 layered hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified and as directed. 78 Rotational moulded polyethylene water storage tanks of 500 Litres capacity, (cylindrical vertical tanks with closed top) 03 layered hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified and as directed. 79 supply and fixing in repair ball valve high pressure PTMT with epoxy coated aluminium rod& high density plastic ball 20mm dia bore all as specified and directeed. 80 15 mm bore gun metal globe or gate valve with iron wheel head screwed both end for iron pipe fixed in repairscomplete all as specified and directed. 81 20 mm bore gun metal globe or gate valve with iron wheel head screwed both end for iron pipe fixed in repairscomplete all as specified and directed. 82 Taking down eaves gutters and rain water pipe , soil and waste pipe (any size or pattern ), includding all fittings, heads , shoes bends , swan-necks etc . complete all as specified. 83 110mm bore PVC SWR Type-B ( pressure not less than 6 kg /cm2) pipes single socket in any length with rubber ring joints fixed to wall etc., complete all as specified and directed. 84 75mm bore PVC SWR Type-B ( pressure not less than 6 kg /cm2) pipes single socket in any length with rubber ring joints fixed to wall etc., complete all as specified and directed. 85 PVC (SWR) bends any radius 110mm dia with oval access doors fixed in repairs complete all as specified and directed. 86 PVC (SWR) bends any radius 75mm dia with oval access doors fixed in repairs complete all as specified and directed. 87 PVC SWR 110mm dia Type-B ( pressure not less than 6 kg /cm2) pipes in any length fixed to walls with PVC/MS holder or clamps and conforming to IS-1729 complete all as specified and directed. 88 PVC SWR 75mm dia Type-B ( pressure not less than 6 kg /cm2) pipes in any length fixed to walls with PVC/MS holder or clamps and conforming to IS-1729 complete all as specified and directed. 89 PVC (SWR)110 mmjunction single, (Single T) equal or unequal ordinary or inverted with spigot or socket branch with oval access door fixed in repairs all as specified and as directed. 90 PVC junction, double (double Y), equal or unequal, ordinary or inverted with spigot or socket branch of 75mm bore with access door, complete all asspecified and directed. 91 PVC cowls 110mm fixed in repairs complete all as specified and directed. 92 PVC cowls 75mm fixed in repairs complete all as specified and directed. 93 PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement complete all as specified and directed. 94 Taking up or down 15mm dia steel water tubing and connections all as specified and directed. 95 Taking up or down 20mm dia steel water tubing and connections all as specified and directed. 96 Mild steel galvanized steel tubing 15mm bore medium grade with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed. 97 Mild steel galvanized steel tubing 20mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. 98 CP angle valve/concealed stop cock of cast copper alloy (ISI Marked) chromium plated fancy type scrwed down high pressure with capstain head screwed both ends for iron pipe 15mm bore incl add if fixed in repairs complete all as specified and directed. 99 S&F in repairs PVC valve less, Symphonic action type, flushing cistern of capacity 10 litres, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete, fixed in repairs complete all as specified and as directed. 100 Vitreous china squatting pan "Orissa Pattern" size 580 x 440 mmin white colour with integral foot rest incl lime mortor, "S" trap fixed in repairs complete all as specified and directed.Cat Part No-20042 (ECO) of Hindware or equivalent cat part of make as specified in list of makes as approved by GE. 101 Vitreous china wash down water closet pan (pedestal pattern), (size 570mmx460mmx380mm), white (excluding fixing bolts, flushing cistern and flush pipe) with "P" or "S" trap, including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. Complete fixed in repairs complete all as specified and directed. Make- Hindware Model Universal Cat No 200012(S-25.5/P-18) or equivalent as in list of makes as approved by GE. 102 Plastic water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, including taking down of existing seat cover all as specified and directed. 103 Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.2 meter long flexible spirochrome flex tube and ABS wall hook including making connections and fixed in repair in position complete in all respect as specified.Make-Jaquar Cat part no. ALD-573 or its equivalent cat part of make specified in list make, as approved by GE. 104 Toilet paper holder with flap recessed type stainless steel Complete all as specified and directed.Make-Jaquar cat part no. AQN-7753 or its equivalent cat part of make specified in list make, as approved by GE. 105 Vitreous china wall hung wash basin with fixing accessories, white, flat back, size 550mm x 440mm x 185mm full pedestal including 15mm bore CP Central hole Basin Mixer with Popup waste system with 450mm long braided hoses for mixing hot and cold water screwed down for iron pipe including 32mm dia waste coupling,waste pipe, cutting for and pinning in ends of brackets or erecting standporcelain stopper a pair of CI brackets fixed in repair complete all as specified and directed by Engineer in charge.Make-Jaquar (Queens prime) cat part no.QQP-7169BPM or its equivalent cat part of make specified in list make, as approved by GE. 106 PVC connection 15mm size of length 600mm, with PTMT nuts supplied and fixed in repairs complete all as specified and as directed 107 S&F in repair waste pipe for SINK/WHB/Urinal for 32/40mm dia all as specified & as directed. 108 Swivel shower of CP any colour for fixing with 15 mm pipe ,with shower arm of size 195 mm long with bend of 45 degree with flange of any colour supplied and fixed in repairs complete all as specified and directed. 109 Bib taps (Long body) for 15mm bore dia of pipe, fancy type chromium platedwith crutch or butterfly handle, screwed down for iron pipe or for brass ferrule and fixed in repairs complete all as specified and directed.Cat Part No-CON-107KN of Jaquar or its equivalent cat part of make specified in list make, as approved by GE. 110 Bib tap (long body)15 mm standard of PTMT any colour high pressure screwed for iron pipe and fixedin repairs complete all as specified and directed. 111 Chromium plated fancy type quarter turn Pillar cock screwed down high pressure with crutch or butterfly handle screwed both end 15 mm bore dia fixed in repairs all as specified. Make-Jaquar Cat part no. FON-40011 its equivalent cat part of make specified in list make, as approved by GE. 112 15mm bore brass CP wall mixer with provision for overhead shower arrangement with 115mm long bend pipe on upper side for mixing hot and cold water supply screwed down with connecting legs CP extension nipple & wall flange connector for hand shower arrangement with connecting Legs, wall Flanges & wall bracket for hand shower for mixing hot or cold water, screwed for iron pipe and fixed in repairs, complete all as specified and directed.Make-SOL-6273UPR of Jaquar or its equivalent cat part of make specified in list make, as approved by GE. 113 CP grating with or without hole100 mm dia fixed in repairs all as specified and as directed. 114 Stainless steel Soap dish, any type, fixed with plugs chromium plated brass screws fixed in repairs complete all as specified and as directed.Cat part No-AQN-7733 of Jaquar or its equivalent cat part of make specified in list make, as approved by GE. 115 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC Sheet 0r 6mm thick commercial plywood fixed to wdn plugs with CP Brass screws and cup washers fixed in repairs, completeall as specified and as directed.
|
