|
Tender For Furniture and light work next to the main kutch in the development block complex Myorpur- 1 Clearing grass and removal of rubbish up to a distance of 50 m out side the periphery of the arae cleared. DSR Sl. No.2.32 2 Earth work in Excavation by mechanical means ( Hydraulic excavator ) / manual means in foundation trenches or drain ( not exceeding 1.5 m in width or 10 sqm on plain ), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, width in a lead of 50 m. DSR Sl.No. 2.8.1 3 Random Rubble Masonary with hard stone in foundation and plinth including levelling up width cement concrete 1:6:12 ( 1 cement:6 coarse sand :12 graded stone aggregate 20 mm nominal size )up to plinth level with : Cement Mortar 1:6 ( 1 cement : 6 coarse sand ) DSR Sl. No. 7.1.1 4 Providing and in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level:1:4:8 ( 1 cement:4 coarse sand (zone !!!) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources ) DSR Sl.No. 4.1.8 5 Brick work with common burnt clay (non modular) bricks of class -150 in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand) DSR - 2.35.3.1 As per SI No- 6.1.1 6 15 mm thick cement plaster of mix 1:6 ( 1 cement & 6 course sand ) Inner Side DSR 10.31 as per IS 13.5.2 7 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone ) finished with floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. 40 mm thick floor 20 mm nominal size stone aggregate. DSR - 9.21.2 As SI No. 11.3.1 8 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources). Above Plinth Lvl DSR 4.1.8 As Per SI No-5.3 9 Steel reinforcement for R.C.C. work ready to use "cut and bend" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete in Thermo-Mechanically Treated bars of grade Fe-500D or more. DSR 5.1.2 As per SI. No.- 5.22 B.1 10 Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer,over the plasterd wall surface even and smooth surface. DSR- 13.3.1 as per Sl no. -13.80 11 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre. DSR 13.4.2 as per Sl no. -13.41.1 Two Coats 12 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, priming coat of approved steel primer, but excluding the cost of other fittings,glass panes complete all as per approved design, (sectional weight of only steel members shall be measured for payment). as per SI no. 10.11.1 13 Steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. In grantings, frames, guard bar, ladder, railing, brackets, gates and similar works as per SI no. 10.25.2 14 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. DSR 1.10.1 15 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required DSR1.11 16 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire. DSR 1.14.3 17 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire DSR 1.14.2 18 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. DSR 1.32 19 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. DSR 1.31 20 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00,Air deliveryminimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase ACSupply, earthing etc. complete as required. DSR - 19.1 21 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. DSR -1.25 22 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. 4 way (4 + 12), Double door DSR -2.4.1 23 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. 6 way (4 + 18), Double door DSR - 2.4.2 24 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole DSR - 2.10.1 25 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole DSR- 2.10.3 26 Add for Invertor wiring in wiring point for Light/Fan/Plug with 1.5 mm Cu Wire. UPPWD - (189 A ) 27 Supply and fixing of LED Tube Light batten fitting suitable for up to 1 X 22 watt LED tube light on surface complete in all respect. - CAT-AAA UPPWD 1413 (A) 28 Supply and fixing of recess/Surface/Pendent mounting round 6 Watt 8 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect CAT-AAA UPPWD -1401 29 Supply and fixing of recess/ Surface/ Pendent mounting round 10 to 15 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect.. CAT-AA UPPWD - 1402 30 Supplying and fixing of 63 Amp. 4 Pole MCB (10KA) "C" curve, CAT-A UPPWD-1020(A) 31 Supply and fixing coverd sofa 3 seater+2 seater+2 seater (heavy duty) MR 32 Supply and fixing coverd sofa 2seater (heavy duty) MR 33 Supply and fixing centar table MR 34 Supply and fixing Bed 6feet*6.6*5 inch king size diwan bed with storade MR 35 Supply and fixing 1.5 ton AC with 4 kva 130 volt to 290 volt stabiliser MR 36 Supply and fixing standard 3-seater stainless steel waitinh chair for wating area MR 37 Supply and fixing standard 6-chair set with dinning table MR 38 Supply and fixing 3-feet*6.6-feet storage almira MR 39 Supply and fixing of bed sheet MR 40 Supply and fixing Bed 6feet*6.6*5 inch king size Mattress MR 41 Supply and fixing of pillow MR 42 Supply and fixing of freeze MR 43 S/F of sign board Please Enable Macros to View BoQ information
|
