|
Tender For State Level Khadi Exhibition 2025-26- 1 Construction of stall/pavillion for single stall within the structure. 2 Construction of stall/pavillion as per specification multiple stall within the structureSpecifications:- 1. Super structure with salballha post and bamboo should be made properly to stand steady during heavy rain/wind as per direction in the site. Height should be of 16, Iron wire and coir rope should be used in the structure.2. Roof, properly fitted with waterproof and fire-proof tarpaulin on bamboo structure. Total height will be 16 with at least 2 sloping on the one side or in all four sides as the case may be. As per design, 5 to 6 width verandah may be constructed in the front and two other sides of the pavilion. Exposed walls outside the pavilion adjacent to verandah to be covered with plywood (minimum 4 mm thick) painted with approved shade. The shed over the verandah should stand on required number of ply wood pillars of height 8 to 9 and four sides will be 1 each. Gap between two pillars will be 5 (approx). The shed with about 2 slopping will be covered with multi-coloured flex as per selected design fitted with wooden batten frame. 1 width ply panel is to be fitted in the front where the shed touches the pillar. As directed by the authority, either two coat of painting is to be applied on ply pillars and ply panel or these are to be covered with multi coloured flex of approved design.3. All exposed walls inside the pavilion to be covered with plywood (minimum 4 mm thick) painted with approved shade. Ceiling should be covered with white or coloured hessian/cloth/flex fitted with proper wooden framing. The clear height from the wooden floor to the ceiling will be 9 to 10. Outside front wall should be covered with ply wall and painting. Back side should be covered with GI sheet and other two sides be covered with fire proof tarpaulin and GI sheet. Outside exposed wall (three sides) should be completed by covering cloth / coloured jute Hessian/flex with batten frame. One top facia (height 4 to 6) should be made with ply as per design and fitted with wooden frame. Design will be supplied on spot.4. Wooden Platform on floor / ground should be of hard wood board of 1 thick at a height of 6 to 1 high from the ground with proper sloping along with stair / steps for each gate of each pavilion. Floor to be covered with coir/jute mat or synthetic carpet as per approve colour.5. One show window with glass/fibre glass (minimum size 2 X 3) is required in the pavilion/stall for every 500 sq.ft. area. Required number of Show window is to be calculated dividing the area of the pavilion by 500 and rounding off the quotient to next whole number. There should be adequate arrangement for display of handicraft/handloom items (as per direction in the site).6. Sale counter/ running table to be provided and fabricated with 18mm commercial block board or particle board fixed on wooden batten frames adequate for the fair purpose with proper fixing in suitable place (in front of all the four-inside wall) in the pavillon/stall. One shelve/drawer should be fixed inside the counter / table. Top and front side and both the end of the counter / table should be covered by plywood board with two coats of paints. Height of the counter will be 3 from the floor and width 1% to 2. The length of the running counter will be as per instruction (in four sides of pavilion). A storage space-cum-cash counter also have to be provided covered by suitable plywood with one door and locking arrangement for each pavilion/stall as per instruction7. Racks to be provided and fabricated with commercial block board (18 to 20 mm thickness) with vertical partition 3 apart and horizontal partitions (shelve) 1-3 apart more or less and back with commercial plywood covering. Height of racks will be 7-6 to 8 with depth not less than 16. It should be fixed properly on the Back side, Left Side & Right Side of store on wall of counter as per instruction (four sides of pavilion).8. One collapsible gate with locking arrangement is to be fitted in the door of the pavilion for every 80 sq. ft. area. Required number of collapsible gate is to be calculated dividing the area of the pavilion by 80 and rounding off the quotient to next whole number. Size of collapsible gate will be minimum 6 width.9. Front face and top facia of each pavilion/stall should be painted with multi colours as per design with the name of organization/name of stall/DIC (title of pavilion) with proper mural paint/multi colour flex as directed. Front facia should be with ply board and flex printing and fixing as per design/name of the stall/pavilion. 3 Complete construction of godown / Electrical room/Transformer roomSpecification:-Structure of godown should be of bamboo with GI sheet roof and four sides to be covered with fire proof tarpaulin & GI sheet provided with one / two collapsible gate as per requirment.Raised wooden platform with synthetic carpet to be fitted on floor (inside the godown). Height of the platform should be minimum 8 from ground level. 4 Construction of main office/VIP roomSpecification:-Structure would be same as construction of pavilion as stated in [Item.No.- 1 & 2] . Office room should consist of one VIP guest room and announcement and enquiry room, antechamber for MSME official and general room. Provision of construction of two toilets may be made within the main office. VIP Guest room should be well decorated with sufficient window (of fibre glass) [at least 4 windows of size 4X3 or 6x4 each as required]. Doors with all fittings should be fixed in each cubicle / ante-chamber and toilets. Single / Two- or Three-Seater sofa to be supply as per requirement. Flooring with two layer of synthetic carpet according to colour as directed by the authority. Necessary curtain should be fixed in doors fitted with collapsible gates and windows. Construction of structure, roof, walling, platform gate & facia should be made as specified in (1), (2), (3), (4), (5), (8), (9), of [Item.No.- 1 & 2] . Four sides of the upper facia and lower facia are to be covered with multi colour flex, False ceiling made of 2 to 3 width plywood surrounding all sides covered with cloth is to be made in the VIP Room. Below the ply panel at the verandah an arch like structure is to be made with ply wood for decoration. It is to be painted with approved colour. All the exposed portion of rooftop/Sheds are to be covered with multicolour flex as per approved design. 5 Boundary fencing with Gl sheet & cloth walling / cover (view guard)Specification:-Boundary walling with Gl sheet of 8-12 height fitted with salballha / Iron rod and bamboo frame (at least 4 horizontal runners). Fencing should be made properly to stand steady during heavy rain or wind. cloth walling / cover (view guard) to be install to hide the GI Sheet. 6 Temporary Construction of Metal Stage with Iron Proping & Iron Truss and all Iron MemberSpecification:-a) Metal Stage with Iron Proping & Iron Truss and all Iron Memberb) Flooring to be done with 25mm waterproof plyc) Floor of stage should be covered strictly with synthetic carpet according to colour directed by the authorityd) Ceiling of the stage should be covered with high quality decorative cloth (Multi / Matching as per direction)e) Metal Stair case/steps in two sides should be properly fitted and covered with synthetic carpetf) Only backside should be well decorated as per specification. A backdrop made of star flex placed on wooden batten frame as per design and requirement is to be provided.WBKVIBg) Main stage with open on three sidesh) Roof with fire proof and water proof tarpaulini) Well decorated cloth facia to be fitted at the front 7 Audience spaceSpecification:-a) Space for audience to be open in all sides with well decorated cellingb) Construction of this temporary structure with bamboo and salballah should be on ground with fire proof and water proof tarpaulin roof. c) Cloth jhalor (width 1) in the top of auditorium (3 sides)d) Pillars should be covered with clothe) Front facia and two sides should be 8 to 12 high and fitted with well decorated cloth and multi colour flex as per direction.f) Cloth and multi colour flex to be fitted on wooden batten frame.g) A beam like separator made of cloth fitted with wooden batten frame is to be fitted between stage and Auditorium. 8 Green roomSpecification:-A green room to be made in the back side of the main stage with wooden platform (height 1 to 16”) and structure as stated for pavilion in [Item No. 1 , Sl No.- 1,2,3,4] but without rack, counter and front facia. a) Super structure with salballha post and bamboo should be made properly to stand steady during heavy rain/wind as per direction in the site. Height should be of 16, Iron wire and coir rope should be used in the structure. Any deviation from this specification by the contractor awarded the work, will lead to cancellation of the work awarded. b) Roof, properly fitted with waterproof and fire-proof tarpaulin on bamboo structure. Total height will be 16 with at least 2 sloping on the one side or in all four sides as the case may be. As per design, 5 to 6 width verandah may be constructed in the front and two other sides of the pavilion. Exposed walls outside the pavilion adjacent to verandah to be covered with plywood (minimum 4 mm thick) painted with approved shade. The shed over the verandah should stand on required number of ply wood pillars of height 8 to 9 and four sides will be 1 each. Gap between two pillars will be 5 (approx). The shed with about 2 slopping will be covered with multi-coloured flex as per selected design fitted with wooden batten frame. 1 width ply panel is to be fitted in the front where the shed touches the pillar. As directed by the authority, either two coat of painting is to be applied on ply pillars and ply panel or these are to be covered with multi coloured flex of approved design. c) All exposed walls inside the pavilion to be covered with plywood (minimum 4 mm thick) painted with approved shade. Ceiling should be covered with white or coloured hessian/cloth/flex fitted with proper wooden framing. The clear height from the wooden floor to the ceiling will be 9 to 10. Outside front wall should be covered with ply wall and painting. Back side should be covered with GI sheet and other two sides be covered with fire proof tarpaulin and GI sheet. Outside exposed wall (three sides) should be completed by covering cloth / coloured jute Hessian/flex with batten frame. One top facia (height 4 to 6) should be made with ply as per design and fitted with wooden frame. Design will be supplied on spot. 9 Overhead gate (Type -A)Specification:-a)Design of gate and pillar gate is to be submitted by the decorator well in advance for approval by the authority. b)Structure should be of stout salballah and bamboo. Iron wire or coir rope should be used so that gate should stand steady during heavy rain / wind. All the sides of the pillars and top are to be covered by plywood as per approved design. Good quality of 12mm ply, plastic paint/flex should be used. Approximate size of Overhead Gate-Type-A: c)Normally total height of the Gate is 28 to 30, length including pillar at both ends is 40 to 52 and width of each pillar is 4 in all sides as per requirement and availability of space. d)Size and decorative design will be provided at the site as per availability of space. Good quality of paint/cloth/flex should be used as per design. e)Rate should be given in Rupees per sq. ft. of surface area as per design and size of gate according to available space and requirement. Rate should be inclusive of all the cost of material and fixing the same. 10 Road side Overhead gate (Type -C)Specification:-a)Design of gate and pillar gate is to be submitted by the decorator well in advance for approval by the authority. b)Structure should be of stout salballah and bamboo. Iron wire or coir rope should be used so that gate should stand steady during heavy rain / wind. All the sides of the pillars and top are to be covered by plywood as per approved design. Good quality of 12mm ply, plastic paint/flex should be used. Approximate size of Overhead Gate-Type-A: c)Normally total height of the Gate is 28 to 30, length including pillar at both ends is 40 to 52 and width of each pillar is 4 in all sides as per requirement and availability of space. d)Size and decorative design will be provided at the site as per availability of space. Good quality of paint/cloth/flex should be used as per design. e)Rate should be given in Rupees per sq. ft. of surface area as per design and size of gate according to available space and requirement. Rate should be inclusive of all the cost of material and fixing the same. ** Specification is as mentioned in Item No.[25] above except the use of Plywood. Only multi colour flex with batten frame should be used in place of ply wood. 11 Pillar gate (complete construction as per design)Specification:-The structure should be made by bamboo or wood in rectangular shape and fixed by plywood as per design. Pillar gate should be placed in the allotted space in such a way that it should be steady during rain or wind. Top canopy will also be by plywood as per design and synthetic colouring. The flex with wooden frame should be fixed on all sides as per design for printing. Approximate size of one pillar gate: Base 6X12X4 sides, Middle with flex: 10X4X4 sides, Top canopy of height: 4 to 6 with ply as per design. 12 Structure for open haatSpecification:-a) Super structure with salballha post, bamboo structure etc. which should be made properly to stand steady during rain/wind. Roof with GI sheet properly fitted with bamboo/or with waterproof and fire proof tarpaulin, height 15 with at least 2 sloping in two or four sides of roof as per size. Cloth ceiling to be fixed with wooden frame or bamboo frame. Ply facia about 1 width in all four sides to be fitted.b)No counter is required. All sides will be open. No gate or window glass is required. Cloth jhalor (1 width) to be fixed on all four sides at below ceiling. c)Wooden Platform on floor / ground should be of hard wood board of 1 thick at a height of 6 to 1 high from the ground with proper sloping along with stair / steps as required. Floor to be covered with coir/jute mat or synthetic carpet as per approved colour. d)4 high Partition wall made of plywood is to be made at the middle of the Haat parallel to the length with two step shelves (Racks) is to be made on both sides. Two end of the racks are to be covered by ply wood. e)Ply Panel of width 6 to 1 should be made with painting in the top of four sides. Pillars should be well decorated with cloth or ply with painting or multi colour flex printing as per approved design. Flex name as per design is to be fixed on the four sides of ply panel as directed by the authority. All the exposed portion of rooftop/Sheds are to be covered with multicolour flex as per approved design 13 Construction of Security roomSpecification:-Room for Security/Police/Fire/First Aid - Four no. of rooms or as directed are to be constructed within single structure (Approx size:- 40x20) as mentioned at Item No. [1] (1), (2), (3), (4) & (9). Collapsible gate with locking system is to be provided in four stall. 8 high ply partition wall is to be constructed at the middle of the structure parallel to front side with provision of entry from police room and security room to make rest room for police personnel and security personnel. Rest room of police personnel and security personnel is to be separated by ply partition. One no. of counter of size 4 Rft and two no. of chairs are to be provided in each of the four room. Front side should be like pavilion. 14 Food stall/other stall without verandahSpecification:-a)Food stalls with verandah:- No separate rate is required to be quoted as the structure will be like pavilion with interior decoration of Item no. [l] . This rate is applicable. b)Food stalls without verandah:- Required no. of rooms or as directed are to be constructed within single structure as mentioned at Item no. [l] except the construction of verandah. 15 Flex-inkjet print Specification:-Inkjet Flex printing to be printed in Multicolour as per design and specification and fitted with wooden or iron frame for back lit or front lit arrangement 16 Cloth Jhalor/cloth fencing without wooden frame [36x36 at Audience Space] 17 Collapsible gate/iron gate (Single) 18 Extra counter 19 Extra rack [8 Wide Total 110Nos] 20 Iron stair case/ladder Hight - 4 [ 3-3.5 Wide] 21 Waste paper basket/dustin for Office / VIP / Guest / Green Room 22 Wooden platform with synthetic carpet 6 to 1 high 23 Window with glass [4x4 Total 2 Nos] 24 Multi colour star flex printing with wooden batten frameSpecification:-Multicolour Star flex printing to be printed as per design and specification and fitted with wooden batten frame 25 Multi colour star flex printing without wooden batten frameSpecification:-Multicolour Star flex printing to be printed as per design and specification and fitted without wooden batten frame 26 Multi colour black back flex printing with wooden batten frameSpecification:-Multicolour black bag flex printing to be printed as per design and specification and fitted without wooden batten frame 27 Multi colour black back flex printing without wooden batten frameSpecification:-Multicolour black bag flex printing to be printed as per design and specification and fitted without wooden batten frame 28 Normal flex printing & fixing on standy 29 Extra coat of painting - 1 coat 30 Extra coat of painting - 2 coats 31 VIP Cushion Chair with arm (Steel) 32 Cloth cover for VIP Steel / Wooden Cushion Chair , With Arm / Without Arm 33 Office Table (PVC) with cover (colour as per direction) 34 Ordinary Sofa Set (3 seater) 35 VIP Sofa Set (3 seater) 36 Cover for VIP / Executive Sofa Set (1 seater) - Colour as per direction 37 Flower vase (Big) with Natural Flower Bunch etc. 38 Flower vase (Small) with Natural Flower Bunch etc. 39 Pradip with stand (Big) 40 Lecture Desk 41 PVC Table 42 PVC Table cloth 43 Fibre/Plastic (molded) chair (without arm) with cloth cover and ribbon 44 Fibre/Plastic (molded) chair (without arm) 45 Coffee/Tea/Centre Table 46 Garden Umbrella 47 Glass Top Centre Table- round shape 48 Decorative Use Me Drum 49 Tray (big) 50 Plastic Bucket (big) 51 Door Mat 52 Water Glass with lid 53 Cup & Plate for tea (6 pc set) 54 Full size plate for lunch/dinner 55 Half size plate for tiffin 56 Spoon 57 Mirror 58 Scissor (medium size) 59 Synthetic Curtain1. Colour of Curtain finalised by the office2. Size of Curtain as per requirements 60 Cotton Curtain1. Colour of Curtain finalised by the office2. Size of Curtain as per requirements 61 Supply & Decoration of Tabloo for advertising purpose (Mini Truck)1. Supply of Mini Truck (TATA Ace) 2. Printing of Flex (creative to be provide by the office) with batten or without batten frame as per requirement 3. Including installation of Flex and sound system on vehicle 62 Rate for advertising with Tabloo1. Rate should be in per day basis 2. Atleast 6 hours per day travelling 63 Main line(wire as per load)/ cable line from main switch / panel Board to pole point. Main wire 31/2 core PVC/AL Cable to be fixed underground or overhead with alkaline or poly pipe. 31/2 core 240 sq. mm. to 400 sq. mm. XLPE/Ar., AI. Cable 64 Main line(wire as per load)/ cable line from main switch / panel Board to pole point. Main wire 31/2 core PVC/AL Cable to be fixed underground or overhead with alkaline or poly pipe. 31/2 core 95 sq. mm to 120 sq. XLPE/Ar., Al. Cable 65 Main line(wire as per load)/ cable line from main switch / panel Board to pole point. Main wire 31/2 core PVC/AL Cable to be fixed underground or overhead with alkaline or poly pipe. 4 core 10 sq. mm. to 25 sq. mm. XLPE/Ar., AI. Cable 66 Main wire 4 core 10 sq. mm. to 25 sq. mm PVC cable. 67 Main wire 2 core 10 sq. mm. PVC cable. 68 Single core 7/0.029 or 7/0.036 PVC in.sulated copper wire. 69 Earthing with 50 mm dia GI pipe 2.5 mtr. to 3 mtr. long with 6 SSG Alu. Earth wire including GI nuts, bolts, washer etc., & dismantling the same for DG Set Neutral & body 70 Providing on hire basis following switches etc. on suitable angle iron frame incl. providing inter connection wiring with socketing earthing attachment etc. 500 volt 400 amp. To 800 amp. 35-50 KA MCCB. 71 Providing on hire basis following switches etc. on suitable angle iron frame incl. providing inter connection wiring with socketing earthing attachment etc. 3 Phase 440 V Panel Board with 100 amp to 200 amp MCCB 72 Providing on hire basis following switches etc. on suitable angle iron frame incl. providing inter connection wiring with socketing earthing attachment etc. 100 amp to 200 amp Main Switch 73 Providing on hire basis following switches etc. on suitable angle iron frame incl. providing inter connection wiring with socketing earthing attachment etc. 400 Amp. to 630 Amp. 4 Pole rotary change over switch 74 Pilot Lamp with fuse 75 Danger Board 76 Distribution wiring in 2 x 2.5 sq. mm.Single core wire to 5 Amp. Plug point including fixing plug socket control switch board including exist size on hire basis and dismantling (Avg. run 3 mtrs.) 77 Supply & fixing 150 Watt to 300 Watt LED colour metal light fitting on hire basis including replacement of fused lamps 78 Supply & fixing of 30 Watt to 100 Watt LED White metal light fitting on hire basis including replacement of fused lamps 79 S & F hire basis twin commercial type LED tube light 40. 40 watt fittings complete 80 S & F hire basis CFL LAMP fittings complete 5watt to 32watt 81 S & F hire basis Night Lamp fittings complete 10 watt to 25 watt 82 S & F hire basis lamp with holder fittings complete- 100 watt 83 S & F on hire basis LED (rope) light for boundary / tree decoration etc. 84 S & F on hire basis 400mm. Swing pedestal fan 85 S & F on hire basis 1200 / 1400 mm. sweep ceiling fan 86 S & F on hire basis Stage Light for programme -500 watt mirror light 87 S & F on hire basis Stage Light for programme - follow sport light 88 S & F on hire basis Stage Light for programme - Operation board 89 S & F on hire basis Stage Light for programme - 3/54 LED par 90 S & F on hire basis Stage Light for programme - 1000 watt par light 91 S & F on hire basis DMX 512 Controller 92 S & F on hire basis Avolite Controller 93 S & F on hire basis 16 core 2.5 sq.mm PVC Cu Flex Cable 94 S & F on hire basis Pole top ring suitable for mounting 6-8 nos. luminiere 95 Supply and installation on hire basis sound proof Generator set with complete fittings having capacity (excluding fule & oil) -125 KVA 96 Rate of Generator Fule 97 Rate of Generator Oil (Engine Oil) 98 Supply, installation and commissioning of 5 megapixel (1600x1200) high resolution CCTV camera (HD 1080 pixel, real time video recording, true day/night vision, IP-66 ratings) alongwith sufficient storage during the event and other accessories on hire basis incl. operation and maintenance.[One Set Including - 1No. 16 Channel NVR, 16Nos. 5Mp Camera, Sufficient HDD for recording during Mela 24x7, DC Power Source,Large Monitor Display,Mobile application Live view, Require Wire. etc.] 99 Supply & Installation of LED TV - 65 including operation 100 Temporary arrangement to receive power with contract demand to the tune of 800 KW from point of supply at 11 KV, 3 phase, 50 cycles per sec A.C. and transformation of power to usable voltage to suit the requirement of electrical installation at fair ground supplying suitable transformer and all other accessories as per requirement incl. earthening on hire basis maintaining all safety norms and other[WBSEDCL / CESC cost] 101 S & F hire basis sound / public address system Microphone (ordinary) with stand 102 (do) Microphone (cordless) 103 Gooseneck Microphone 104 (do) Cassette / CD / DVD Player 105 (do) Mixture machine 106 S & F on hire basis Sound Syaytem for cultural programme. Having about 8 microphones (with one cordless) / corresponding sound box, mixer amplifier and other accessories. 107 Supply & Maintain of Un-Skilled: Security Guard 108 Supply & Maintain of Semi-Skilled: Security Guard 109 Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.(a) Depth of excavation not exceeding 1,500 mm.Ground Floor 110 Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) Ground Floor 111 Single brick flat soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with powdered earth or local sand. 112 I) Cement concrete with graded stone ballast (40 mm size excluding shuttering)In ground floor(A) [Pakur Variety]. 113 Brick work with 1st class bricks in cement mortar (6:1) (a) In Foundation & Plinth, ground floor 114 125 mm thick brick work with (1:4) sand cement morter incl.scafolding, curing etc all complete with 1st class brickGround Floor 115 Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints or rougening of concrete surface, including throating, nosing and drip course where necessary (ground floor) c) 15mm thick Plaster(6:1) Out side & Chajja 116 Neat cement punning about 1.5 mm. thick in wall, dado, window, sills, floor, drain etc. NOTE : Cement 0.152 cu.m. per 100 sq.m.Ground Floor 117 Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour.In ground floor.3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement).Using grey cement 118 Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10 mm.) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. 2. Add extra for each addl. Floor over the rate for item no. 30 (i) upto 4th. Floor - Rs.5/- per sq.m. [ 3rd Corrigenda Page no. 36, item no. 22 ] 119 With sand cement mortar (1:3) 15 mm. thick & 2 mm. thick cement slurry at back side of tiles using cement @ 2.91 kg./sq.m. & joint filling using white cement slurry @ 0.20 kg./sq.m. 120 Supplying ,fitting & fixing Eco-friendly, Moisture Resistant and Incombustable Gypsum plaster board/tiles (Density > 700Kg per Cu.m) conforming to IS 2095- Part 1, 2011 of size 595mm X595mm of approved design and brand placed in the Grid module to form a false ceiling all complete as per drawing & direction of Engineer - in- Charge.False ceiling with (ii) 12.5mm thick Square edged Gypsum Plaster Board / tiles 121 Supplying, Fitting & Fixing Factory made prelaminated P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm Prelaminated PVC sheet miter cut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 Nos for horizontal member etc. complete as per Manufacturer?s specification and direction of Engineer-in-Charge. 122 Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th. both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in-Charge.In ground floor. 123 Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately).(a) 40mm X 6mm, 250mm Length. 124 Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark.(iii) 75mm. X 40mm. X 1.12mm. 125 Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws:(ii) 75mm long x 10mm dia. bolt.. 126 Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete:(a) With continuous plate base (Hexagonal/ Round rod)(iii) 100 mm grip x 12 mm dia rod. 127 Wood work in posts, post plates, rafters, battens, truss members, purlins etc. fitted and fixed complete (excluding the cost of bolts, paints, but including the cost of nails, screws etc.) For VIP Toilet(The quantum should be corrected upto three decimals) 128 Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugation minimum side lap. (Payment to be made on area of finished work)(GCI sheet to be supplied by contractor) (i) In Roof:-a) With 0.60 mm thick sheet For VIP Toilet 129 Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) For VIP ToiletGround Floor 130 Applying Interior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of the Engg-in-charge. [In Ground Floor] (b) Two Coats i) Water based interior grade Acrylic PrimerFor VIP Toilet 131 Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) :(Two coats)ii) Luxury Quality 132 Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4)band all round and cement brick work (1:4)upto 0.90 metre from top with 20mm thick cement plastering (1:4)to inside face upto the depth of cement brick work, 15mm thick cement plaster (1:4)on outer face from top of the well upto G.L.and 6 mm thick cement plaster (1:4)on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size ) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3)with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C.manhole cover (heavy type )of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6)and 1.00m inside dia. Other Manufactures not Specified 133 Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc.(a) With P trap 134 Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete. (a) E.W.C. (ii) Plastic (hallow type) white 135 Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc 136 Supplying,fitting and fixing approved brand P.V.C. CONNECTOR whitflexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia. (iii) 600 mm long 137 Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps. (iii) 900 mm long 138 Supplying, fitting and fixing towel rail with two brackets. (a) C.P. over brass (ii) 25 mm dia. and 600 mm long 139 Supplying, fitting and fixing bib cock or stop cock.(a) (i) Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand). 140 Supplying, fitting and fixing bib cock or stop cock. f) (i) Polythene Bib Cock / Stop Cock (HD) with metal inlet (EMCO / ATLAS or equivalent)15 mm 141 Supplying, fitting and fixing pillar cock of approved make. a) (i) CP Pillar Cock - 15 mm. (Equivalent to Code No. 507 & Model - Tropical / Sumthing Special of ESSCO or similar brand). 142 Supplying, fitting and fixing shower of approved brand and make.(c) Chromium plated Hand shower 70mm dia Round Shape Single flow with Flexible Tube & fittings(Equivalent to Code No. ESH-5512 & Model Tropical / Sumthing Special of ESSCO or similar). 143 Supplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. (a) For Exposed Work(i) CPVC Pipes Class-1, SDR-1115 mm 144 20 mm 145 50 mm 146 Supplying, fitting and fixing Peets valve fullway gunmetal standard pattern best quality of approved brand bearing I.S.I. marking with fittings (tested to 21 kg per sq. cm.). (iv) 50 mm dia 147 Wash basin vitreous china of approved make (without fittings)supplied,fitted and fixed in position on 75mm X 75 mm X 75 mm wood blocks and C.I. brackets including two coats of painting of C.I. brackets. (ii) 550 mm X 400 mm size 148 Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete. (ii) 470 mm X 280 mm X 340 mm 149 Supplying, fitting and fixing Squating plate with integral flushing in white vitreous chinaware of approved make in cement concrete (6:3:1) with jhama chips complete. (Payment of concrete will be paid seperately).(i) 450 mm X 350 mm 150 Supplying, fitting and fixing urinal flush pipe fittings of approved brand. (c) C.P. urinal flush pipe fittings range of three 151 Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm 152 Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately). 15 mm 153 20 mm 154 50 mm 155 For Concealed Work20 mm 156 Supplyig, fitting, fixing of UPVC pipes (B Type) & fittings conforming to IS-13592-1992A) (i) Single Socketed 3 Meter Length(b) 110 mm 157 x) Bend 87.5º (b) 110 mm 158 xxi) 110 X 110 P Trap 75 mm 159 Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m.a) In ground floor including roof. 160 Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m.In ground floor including roof. 161 Dismantling artificial stone flooring upto 50 mm. thick by carefully chiselling without damaging the base and removing rubbish as directed within a lead of 75 m..In ground floor including roof. 162 Taking out carefully G.C.I. or C.I. or asbestos sheets (including ridges etc.) from roof or wall after unscrewing bolts, nuts, screws etc.and stacking the material at site as directed. 163 Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge 164 Supplying P.V.C. water storage tank of approved quality with closed topwith lid (Black) - Multilayer (b) 1000 litre capacity Please Enable Macros to View BoQ information
|
