|
Various Civil Work At Acb Jhalana Doongri, Jaipur.=1.00 Providing gola 75x75 mm in cement concretee 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 10mm and down gauge) Including finishing with cement mortar 1:3 (1 cement 3 fine sand) as per standard design: 2.00 Making khurras 450 x 450mm with average minimum thickness 50mm cement concretee 1:2:4 over P.V.C. Sheet 1 Mtr. x 1 Mir. x 40micron finished with 12mm cement plaster 1:3 and one coat of neat cement, rounding edges and making and finishing the outlet complete. 3.00 Providing & laying broken glazed tities on roof (broken glazed sies not less than 9 Kg/sqm) on top of hot bitumen 1.7 Kg/Sqm. (1.40 Kg of VG-40 (30/40 )grade and 0.30 Kg/Sqm. Of VG-10 (80/100) grade) and joints filled with cement mortar 1 2 (1 cement: 2 marble dust mixed with water proofing compund all complete as per direction of Engineer-in-charge. 4.00 Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing upto any pitch including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.1 plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs Incorporating minimum 10.3% Ultra-vollet stabiliser in resin system under approximately 2400 psl and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall confolm to IS 10192 and IS 12866. The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 5.0mm thick (Wt. 8.4 Kg./Mtr. So. Providing and laying of paver block as per IS 15658 2006 (Indian standard for precast concretee block for paving- specification) and IRC SP:63-2004 (guidelines for the use of interlocking concretee block pavement) M-30, 60 mm thick to be used in non traffic areas like building premises, monument premises, land scapes, public gardens/park, domestic drives, paths and pallos, Embankment slopes, sand stabilization Area etc. (As per table 1 of IS 15658:2006 Category A Denated units to key Into each other on four faces zigzag shape as per IRC SP 63:2004 6.00 Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish: 20mm thick. 7.00 Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 150 m lead With cement mortar 1:4 (1 cement: 4 coarse sand) 8.00 Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3mm thick water proofing membrane, black finished reinforced with glass fiber matt consisting of a coat of bitumen primer for bitumen membrane 0.40 Itrisq.mt. by the same membrane manufacture of density at 25°C, 0.87-0.89 kgitr and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under Joint strength in longitudinal and transverse direction at 23°C as 650/450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D-5147. The laying of membrane shall be got done through the authorized applicator of the manufacturer of membrane. 3 mm thick 9.00 Providing and fixing in CM 1:4 double paltam (rebated) stone door window and ventilator frames of approved quarry : Size 125 x 100mm 10.00 Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS: 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. With brass cover plate Providing and laying in position cement concretee Including curing. compaction etc. complete in specified grade excluding the cost of centering and shuttering All work up to plinth level. M15 grade Nominal Mix 1: 2: 4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size 12.00 Half brick masonry in Superstructure, above plinth level upto floor V level using bricks of designation 75 Cement mortar 1: 4 (1 cement: 4 coarse sand) 13.00 Add extra for Fixing glazed/ Ceramic Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, using 5kg. adhesive per sqm of tile area, in average 3mm thickness instead of cement mortar. 14.00 P & F 1st qualityHeavy Duty Vitrified Polished Digital ties on floor, skirting and steps etc. in different sizes (thickness minimum 10mm) with water absorption less than or equal 0.08% and conforming to IS 15622 of approved make in all colour and shade, lald with 20 mm thick CM 1: 4 Including grounting the joints with white cement and matching pigment etc complete. Size 300mm x 450mm 15.00 P & F 1st qualityHeavy Duty Vitrified Polished Digital ties on floor, skirting and steps etc. in different sizes (thickness minimum 10mm) with water absorption less than or equal 0.08% and conforming to IS 15622 of approved make in all colour and shade, lald with 20 mm thick CM 1: 4 Including grounting the joints with white cement and matching pigment etc complete. Size 600mm x 600mm Providing and foxing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Silis Counters, Floors etc. lald on 12mm (Av.) thick base of cement mortar 1:3 (1 cement: 3 coarse sand) jointing with white cement mortar 1:2 (1white cement: 2 marble dust) with pigment to match the shade of the marble slab Including grinding, rubbing and polishing complete. South Zed Black Above 3601 Cm2 Slabs 17.00 Extra for providing edge moulding to 15-18mm thick marble/Granite Kota stone counters, Vanities etc. Including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite/Kota Stone Work Half Edge moulding 18.00 Providing and faxing IS: 3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete. 19.00 Providing and fixing in position collapsible steel shutters with vertical M.S. Channels 20 x 10 x 2mm and bracket with flat iron diagonals 20 x 5mm. size with top and bottom rail of T-iron 40 x 40 x 6mm. with 40mm dia steel pulleys/ball bearing complete with bolts, nuts locking arrangements Inside and outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer. (To be measured and paid as per outer dimension). 20.00 Providing and foxing M.S. sheet 1mm thick single leaf door shutter in angle Iron frame 35x35x5mm suitabily diagonally braced with 25x3mm flat iron above and below lock rall of size 50x5mm beading extra Including all fittings, as per direction of Engg. Incharge but excluding cost of chowkhats: Including two coats of anit-corrosive red oxide primer paint Add extra for double leaf shutters. 21.00 Supply and fixing in cement mortar welded hand ralling made out of MS round or square bars, flats etc. for staircase or verandah as per design complete in all respect (wooden or PVC hand ralling to be paid extra) with priming coat of red oxide. 22.00 Labour Charges for Removing & Refixing the water Storage Tank of all sizes and including all Necessary fitting complete in all respect as per approved sample and direction of engineer in charge.
|
