|
Tender For Special Repair To Building No. 03-T (Family Ward) At Mh Lansdowne.; 1 Taking down chowkhats or frames with shutters( without taking off shutters from the frames) of following size complete all as specified and directed:- 2 Area not exc 1.5 sqm each 3 Area exc 1.5 sqm but not exc 4 sqm each 4 Taking down shutters of any description, of following size complete all as specified and directed:- 5 Areaexc 1.0 sqm and not exc 2.0 sqm each 6 S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows and other frames/ chowkhat of following size comprising of virgin PVC polymer having K-value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and direction. Note: (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable andvariation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.(ii) M.S. hold fast/ lugs or SS dash fasteners shall be measured and paid for separately. 7 65 mm x 100mm size 8 65 mm x 125mm size 9 M&L for 30 mm thickfactory made single extruded WPC(Wood Polymer Composite) solid decorative type flushdoor shuttercomprising of virginpolymer of K value 58-60 (Suspension Grade), calciumcarbonate and natural fibers (wood owder/ rice husk/ wheat husk) and non toxic additives (maximum toxicityindex of 12 for 100 gms) having minimum density of 650kg/cum and screw withdrawal strength of 1800 N (Face)& 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 andresistance to spread of flame of Class A category withproperty of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVCfoil of minimum 14 microns thick of approved designpasted with hot melt adhesive on both faces of shutterand fixing withbutt hinges of requiredsize with necessary full body threaded star headedcounter sunk S.S screws,acomplete all as specified and directed. 10 M&L for 30 mmthick molded WPC wire mesh factory made 1005 decorative type, moulded,panel door shutter prepare to receive Mesh, gauze etc (single or two panel Including wire mesh(confirming as per IS: 4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with wood grain texture and back side plain with density not less than 600kg/cum manufactured by an ISO : 9001-2015 certified company.The door should be water proof, termite proof, termite proof, fire retardent and having screw holding capacity.complete all as specified and directed. 11 S&F MS butt hinge, medium weight, cold rolled and fixed of following size complete all as specified and directed:- 12 100 mm long 13 S&F 250 mm long anodised aluminium sliding door bolt (ISI marked) with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of following size complete all as specified and directed:- 14 S&F 150mm anodised aluminium handles cast typecomplete all as directed and specified 15 S&F 150 mm long anodised aluminium barrel tower bolts (ISI marked) of extruded sectioncomplete all as directed and specified 16 S&F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed. 17 S&Fincludingfabricating of aluminium colour powder coated having minimum thickness of powder coating 50 micron fordoor / window/ ventilator frame, shutters & partition including necessary joining cleats, glazing clips, aluminium snap beading having minimum wt 100gm/RM, rubber neoprene gasket, screws, dash fasteners, rawel plug for fixing of screw in wall or flooretc., aluminium sections as approved by GE complete all as specified and directed.Note : - (i) Builders Hardware shall measured and paid separately under respective item of Schedule "A" .(ii) Only weight of aluminium section shall be measured and paid. No claim what so ever shall be entertained by the Govt on this account. (iii) Thickness of section shall not be more than 2mm.(iv) Window shall be fabricated as per requirement with provision for AC / Cooler openning. 18 S&F aluminium coloured powder coated door/ window (sliding type)/ventilator shutterswithout sash bar aluminium section weighing 0.55 kg/m including necessary locking arrangement, guide wheels, joining cleats, glazing clips rubber packing anodised aluminium snap beading screws etc complete all as specified and directed. 19 S&F 4.8 mm thick plain or tinted glass, ordinary quality including rubber gasket for packing and fixed to aluminium Ventilator/window/ incl necessary cutting / moulding and chamferrring of edges for service window/counters complete all as specified and directed. 20 S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or wire staples complete all as specified and as directed. 21 Supply and fix7 mm thick aluminium coloured power coated grill of Deco Grill pattern DG 104, fixed in aluminium windows / ventilators, etc.including necessary aluminium channels in openings of windows / ventilators, complete all as specified and as directed. 22 Demolition of wall and ceilingboards ( fibre, pulp insulation etc.) or insulation boards/ slabs/ blankets of any thickness, including cover fillets complete all as specified and directed. 23 S&F false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm With Semi perforated 12mm thick micro tegular edged or 10 mmthick square edgedof approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of85% (minimum) to be laid in truehorizontal level suspended on inter locking metal T-Grid of hot dippedgalvanized iron section of 0.33mm thick(galvanized @ 120 grams per sqmincluding both sides) comprising of main T runners of size 15 x 32 mm of length3000mm,cross-T of size 15x 32mm oflength 1200mm and secondary intermediate cross-T of size 15 x 32 mmof length 600mm to form grid module of size 600x 600mm , suspended fromceiling using galvanized mild steel items(galvanizing @ 80 grams per sqm) i.e50mm long, 8mm outer diameter M-6dash fasteners, 6mm dia fully threadedhanger rod upto 1000mm length and L shape level adjuster of size 85x25x2mm.Galvanised iron perimeter wall angle ofsize 24x 24x0.40mm of length 3000 mmto be fixed on periphery wall I partitionwith the help of plastic rawl plugs at 450mm center to center and 40mm long drywall wood screws. The work shall becarried out as per specifications, drawingand as per directions of the Engineer-in Charge. 24 M&L E-boards, ceiling 4 mm thickwith J framed work with main Tee of size 24 x 28.5mm made out of PGI sheet 0.3 mm thick double at web and single at flange and the flange coverd with powder coated sheet 0.25 mm thick and wall angle 24 x 24 x 5 mm powder coated for ceiling and the ceiling boards 60 cm X 60 cm X 4 mm thick, suspended with GI wire 2 mm dia and 2 m average lenght with adjustable hanging device complete including plugging in brick / stone walls with steen rawl plug @ 600 mm C/C and the ceiling boards shall be pressed to the ceiling tee with staple clips at all four sides and painted with two coats of oil bounds distemper after preparation of surfaces including making good all the disturbed portion complete all as specified & directed. 25 S&F 5mm thick Prelam PVCsheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site complete all as specified and as directed. 26 S& F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed. . 27 S&F in repairs for stainless steel non magnetic curtain rod of 25 mm dia with and including fixing brackets and decorative type knobs (as approved by AGE (I)/ GE )both side of each rod complete all as specified and directed.Note: - Measurement will be taken between end point of knobs. 28 S&F 18 mm thick with min density 600 Kg/cu.m LEAD FREE PVC Celuka ply of single side rigid laminate of approved color and other side plain white colour fixed with ss screws and solvent cement/ adhesive to make kitchen cabinet shutters including D Type handle & Piano hinge for fixing the shutter complete as per manufacturer’s instructions complete all as specified and directed 29 S&F continuous (piano) hinges, mild steel bright finish or electro galvanised width of flaps (when open) 30mm complete all as specified and directed. 30 S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished150mm long matt finished complete fixed in position all as specified. 31 Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. 32 M&L for brick work with old size full bricksubclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed. 33 M&L for walling of random rubble masonary, uncoursed well bonded, bedded and solidly hearted, brought upto courses, built in cement mortar (1:6) complete all as specified and directed.Note :- Only quantity of PCC bond stone to be deducted from quantity of random rubble masonary. 34 Description same all as item No. 27 above but except stone complete all as specified and directed.Note :- Old retreived serviceable stone under demolition item shall be used. 35 Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surfacae not exceeding 40mm to face stone for Lime or sand stone and dressing of face beds and joints, as specified of random rubble walling, uncoursed or brought upto course complete all as specified and directed. 36 M&L for raised pointing in cement mortar (1:4) to random rubble masonary uncoursed or brought upto course complete all as specified and directed. 37 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to storeand rubbish off the premises from MoD land complete all as specified and as directed. 38 M&L for coloured glazed ceramic tiles of any design and pattern, 300x450x 7 to 8mmthick, as in dado etc including 10 mm thick rendering in CM (1:4), set and jointed in neat cement slurry and pointed in white of coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622:2017, Group B III with average water absorption between 10% to 15%. Length, width and straightness of sides + 0.20% (Max deviation). Thickness + 4.0% (Max deviation). Straightness of sides and Rectangularity +0.15% (Max Deviation). surface flatness + 0.22% (Max deviation). Breaking strength 500 N (Minimum) and minimum 95% tiles shall be free from visible defects complete all as specified and directed.Note: Shade of the tiles including Colour, design and pattern shall be got approved by AGE(I) 39 M&L for non skid, joint free, coloured ceramic tiles7-8mm thick (Square/Rectunglar), as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles laid with and including over 15 mm thick screed bed in CM (1:6), area of each tiles shall be of following complete all as specified and directed :- 40 Area of each tile exc 0.06 Sqm but not exc 0.18 Sqm. 41 M&L for coloured vitrified tiles of any design and pattern, double charged, 9 to10 mm thick, as in floor etc incl 15 mm thick screed bed in CM (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622:2017, Group B1b with average water absorption less than 0.05%. Length, width and straightness of sides + 0.10% (Max deviation). Thickness + 4.0% (Max deviation). Centre & Edge curvature and warpage + 0.20% (Max Deviation). Breaking strength 1200 N (Minimum) and minimum 95% tiles shall be free from visible defects and area of each is as following complete all as specified and directed :-Note: Shade of the tiles including Colour, design and pattern shall be got approved by GE/ AGE(I). 42 Area of each tile exc 0.18 sqm but notexc 0.36 sqm. 43 Area of each tile exc 0.36 sqm but notexc 0.72 sqm. 44 All as per Item No. 34.01 but 10 mm thick backing coat on fair faces of brick work in CM 1:4in skirting complete all as specified and as directed. 45 All as per Item No. 34.02 but 10 mm thick backing coat on fair faces of brick work in CM 1:4in skirting complete all as specified and as directed. 46 Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed inany mortar and removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. 47 M&L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms, WHB counter and like bedded over and including 20 mm thick screed bed in CM (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. 48 M&L for 60 mm thick coloured rubber moulded glossy finish machine pressed precast concrete interlocking paver block,M-35 Grade with pre-polished, coloured/ laquar finish any shape and size, as approved confirming to IS 15658-2006 with and including over 50 mm thick stone dust/ sand cushining complete all as specified and directed. 49 M&L for 30cm x 30cm x 30 mm thickrubber moulded coloured glossy finish chequered cement concrete tiles, ISI Marked, set and jointed and pointed in neat cement slurry with grey cement and pigment in floors over and including 20 mm thick screed bed in cement mortar (1:6)complete all as specified and as directed 50 M&L for mirror polished machine cut kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror finish polishing over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and as directedNote:- The size of kota stone slab not less than 550mmx550mm (cut size except the location where balanced.) 51 M&L grinding & wax polishing to mirror finish to old kota stone slab flooring & steps, mixed with pigment to match the shade of slab complete all as specified and directed. 52 Demolition of PCC in ground floorand pavings not exc 15 cm thickness below or above ground levelincluding removal of rubbish out side MOD land complete all as specified and directed. 53 M&L for 25 mm thick PCC (1:2:4) type B0(using 12.5 mm graded stone agg) as in sub floor of flooring complete all as specified and directed. 54 M&L for 75 mm thick PCC (1:4:8) type D2, (using 40 mm graded stone agg) as in sub base of floor/ hardstanding/ footpath complete all as specified and directed. 55 M&L for 75mm thick PCC (1:3:6), type C-2 using 40mm graded stone aggregate as in plinth protection, surface finished even & smooth without using extra cement, with and including joint filling (Size 30mm deep x 10mm wide) with sealing compound grade-A at 3m interwal and corner complete all as specified and directed.Note : Joint to be provided at each interval of 3m and corner and cost of the same deemed included in quoted rate. 56 Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water and removing unseviceable materials out side MoD land complete all as specified and as directed. 57 M&L for 10 mm thick plastering on brick or concrete surface in CM (1:6) surface finished even and smooth without using extra cement complete all as specified and directed. 58 M&L for 15mm thick plastering on other than fair faces of brick wall/concrete surfaces in CM (1:4), surface finished even and smooth without using extra cement mixed with WPC as per manufacturer"s instruction complete all as specified and directed. 59 M&L preparation of newly plastered surface of External wall by application of 1mm thick wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying Two or more coats of 100% Premium acrylic emulsion paintand including priming coat of exterior primer applied @ 0.90 litre/ 10 sqmincluding water proofing compound (200ml/bag of cement) complete all as specified and directed. Note- Putty shall be measured and paid seperately. 60 M&L for preparation of newly plastered surface of internal wall by application of 1mm thick wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying two coats of acrylic distemper over a coat of primer using roller all as specified and prescribed by manufacture of paint and as directed at site by Engineer-in-Charge. 61 M&L preparation of oldsurface of External wall by application of 1mm thick wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying Two or more coats of 100% Premium acrylic emulsion paintand including priming coat of exterior primer applied @ 0.90 litre/ 10 sqmincluding water proofing compound (200ml/bag of cement)over one coat ofputty (if required) complete all as directed. Note- Putty shall be measured and paid seperately. 62 Material & Labour for preparation of old surface of internal walland applying two coats of oil emulsion distemperoverputty (if required) make the surface even and smooth of all as specified and prescribed by manufacturer of paint and all as directed. Note- Putty shall be measured and paid seperately. 63 M&L for 1 mm thickAcrylic/WaterProofing Wall Putty & surface finished even and smooth with sand paper completeall as specified and directed 64 Dismantling of timber scantling such as in fillets, rails, runner, rafters, purlins etc under 40 sqcm in section as in un framed work complete all as specified and as directed. 65 Dismantling of plain or corrugated steel sheeting, any gauge, thickness in roof coverings complete all as specified and directed. 66 S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa, AZ-150 as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. 67 S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, AZ-150 as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. 68 S&F rolled mild steel section for Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated conforming to Fe-410-W (Gde-E-250) quality-A complete all as specified and as directed.Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete. 69 S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and or riveted or forged into spikes, framed, barred iron door, ladders, fencing work ect. conforming to Fe-290 Gde E-165 complete all as specified and directed.Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead length where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts), providing and fiitings angle cleats, fish plates, gusset plate etc., also for welding plumbing, truing up and fixing complete. No claim whatso ever shall be entertained by Govt on this account. 70 M&L for twocoats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or grith complete all as specified and directed. 71 Dismantling of timber scantling 40 sqcm and over in section, in any position as in framed work complete all as specified and as directed. 72 M&L for second class hard wood (sal) in timber scantling (clean sawn) as in framed work, roof truss etc complete all as specified and as directed. 73 S&F for 20 mm thick 2nd class hard wood boarding planed one side with butt joints and fixed with nails as in roofs, ceiling partition fascia, barge soffit etc (except flooring and skirting) including dismantling boarding, any description, fixed in any position with nails complete all as specified and directed 74 M&L for twocoats of synthetic enamel paint over a coat of pink primer including preparation of new wood or wooden base surface over 10cm width or grith complete all as specified and directed. 75 Demolition and breaking up drain pipes (PVC/ SGSW/ AC/ RCC pipe) of following bore of pipe, set in cement mortar complete all as specified and as directed:- 76 150 mm bore 77 110mm bore 78 75 mm bore 79 S&F PVC (SWR) pipes single socketed in any length with rubber ring joints and fixed to wall of following size complete all as specified and as directed :- 80 110 mm bore 81 75 mm bore 82 S&F PVC (SWR) multi floor trap, out let dia 75mm, plain with grating including jointing with solvent cement complete all as specified and as directed. 83 S&F PVC (SWR) junction single, (single T) with access door equal or unequal of following size complete all as specified and as directed :- 84 110 mm bore 85 75 mm bore 86 S&F PVC (SWR) bends any radius including necessary cutting in brick wall and making good to match with existing surface of following size complete all as specified and as directed :- 87 110 mm bore 88 75 mm bore 89 S&F PVC (SWR) vent cowl of following size complete all as specified and as directed :- 90 110 mm bore 91 S&F 500 Ltr capacity rotational moulded polyethylenewater storage tanks triplelayered white (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (Minimum weight 15mm-142gms/20mm-210gms/40-690gms) including dismantling of water tanks complete all as specified and directed. 92 S&F 1000 Ltr capacity rotational moulded polyethylenewater storage tanks triplelayered white (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (Minimum weight 15mm-142gms/20mm-210gms/40-690gms) including dismantling of water tanks complete all as specified and directed. 93 S&F in repair vitreous china squatting pan of “Orissa” pattern of size 580 mmx 440mm white with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and as directed. 94 S&F in repair vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic seat and cover, white, closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern and flush pipe) including S trap 110 mmconnection to drain (or outgoing pipe) and to flushing pipe, anti -syphonage pipe, etc., completeall as specified and directed. 95 S&F Vitreous china wash hand basin pedestal type in repair ,white ,flat back of size 550x400mm with PVC connection (15x450)mm long with PTMT nuts and PVC washer and including cutting for pinning in ends, pair of cast iron brackets and provision of PVC waste pipe 32mm of adequate length , waste coupling32mm dia of chromium plated half or full threaded, complete all as specified and as directed. 96 S&Fvitreous china counter top wash hand basin, of size 490 x 400 x 145 mm excluding taps, waste pipe but including waste coupling complete all as specified and directed. 97 S&F in repair PVC valveless, symphonic action type low level flushing cistern white with inlet ball valve, float and handle including brackets, 10 ltr capacity complete with flush pipe for IWC/EWC 32mm dia of make as approvrd by GE complete all as specified & directed. 98 S&F in repairPVC connection 15 mm size 450 mm long with PTMT nut complete all as specified and directed. 99 Taking up or down steel water tubing (GI Pipe) and connections of following bore complete all as specified and as directed :- 100 15mm bore 101 20mm bore 102 S&F galvanised steel water tubing (GI pipe), medium grade with all fittings (ISI Marked) and fixed to wall, floor and ceiling or laid in trenches of following bore complete all as specified and as directed :- 103 15mm bore 104 20mm bore 105 S&F in repairs 15 mm bore bib taps, chromium plated, fancy type, cast copper alloy with crutch handle, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed . 106 S&F in repair fancy type chromium plated 15mm boretwo way Bib cock cast copper alloy with crutch or butterfly handle, screwed for iron pipe or brass ferrule etc complete all as specified and as directed. 107 S&F in repairs 15mm bore Stop valves (angular stop cock), cast copper alloy, fancy type, chromium plated with long shank and cupscrewed down high pressure with crutch or butterfly handleor concealed screwed both ends for iron pipe or for unions complete all as specified and directed.Note for all CP item :- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. 108 S&F in repair chromium plated health faucet, telephonic type with CP 1.00 mtrflexible tube and hooks of approved make suitable to fix to 15 mm bore CP angle valve complete all as specified and directed. 109 S&F in repair CP overhead shower 100 mm round/Square shape single flow (ABS body chromium plated with gray face plate) with rubit cleaning systemfixed in 15mm bore of pipe complete all as specified and directed . 110 S&F15mm dia brass CP wall mixer with provisionfor over head showerfor mixing hot and cold water screwed down for iron pipe and fixed including taking down existing bib tap complete all as specified and directed. 111 S&F15mm dia chromium plated central hole wash hand basin mixer without PWS with 450mm BRAIDED HOUSE hosescrewed down high pressure screwed for iron pipe including taking down existing bib tapcompleted all as specified and directed . 112 S&F 6 mm thick frameless bevelled edge mirror of selected quality glassfixed with CP screw and CP washer and other required fixing arrangement complete all as specified and directed.Note- 1.Size/Shape of Mirror will be decided by Engr in Charge.2. Payment Will be make per Sqm 113 S&F in repair chromium plated brasstowel rail, 20mm dia,60 cm long between flanges complete all as specified and directed. 114 S&F in repair corner glass shelf (with bracket)300 mm all as specified and directed . 115 S&F in repair stainless steel sink with draining board, made out of 1.00 mm thick sheet for kitchen or laboratory with plug, washers, waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mmx 330mmx160mm complete all as specified and directed. 116 M&L concrete bed to drain pipes in PCC (1:3:6) type C2 (using 40mm graded stone aggregate) including packing under and haunching against the sides of pipes after they are laid on slope and tested for following bore sewer pipe line complete all as specified and directed :- 117 150mm bore 118 M&L for salt glazed stone ware (SGSW) pipe, grade A, ISI marked, laid in trenches and jointed in CM (1:1) for following bore of pipe complete all as specified and directed :- 119 150mm bore 120 Demolition of RCC n"exc 15cm thick (below or above grong level) including cutting of reinforcement to facilitate demolition complete all as specified and directed. Note : Reinforcement obtained from demolition will be considered credit Sch as scrap iron. 121 M&L for precast RCC (1:2:4) type B1, (using 20mm graded stone aggregates) as in cover slab (for manholes) and set in CM (1:4) including necessary fair finish formwork complete all as specified and directed. 122 M&L for RCC (1:2:4) Nominal mix (using 20mm graded stone aggregates) as in floor/ roof beam, cantilevers, lintel over 1.5m span complete all as specified and directed. 123 M&L for formwork for rough finish to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etccomplete all as specified and directed. 124 M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 125 M&L for mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming complete and all as specified and directed. 126 M&L for PCC (1:3:6) Type C2 (40 mm graded aggregate) as in foundations, filling and mass-concretecomplete all as specified and directed. 127 M&L for PCC (1:2:4) type B-1, using 20mm graded stone aggregates, as in kerb/ benching/ coping, bed plates, for fixing of hold fast,water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed. 128 Dismantling and taking down old unserviceablepoint wiring of any type (light, fan, socket, power etc) complete with fitting such as switches, sockets, ceiling roses, pendants, lamp holders, light fitting etc including CI/ pressed steel terminals, switch box and making good the disturbed surface of wall/ floor etc to match with the existing surfaces of wall/ floor complete all as specified and directed.Note :- (i) If the contractor fail to make good the disturbed surface of wall/ floor etc and do not match with the existing surface of wall/ floor to the entire satisfaction of Engr-in-Charge, a recovery of @ Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute, the decision of Accepting Officer will be final and binding.(ii) Old fittings/ fixtures / accessories like switches, sockets, lamp holders, regulators etc., if found in serviceable condition shall be removed carefully for reuse in the work or taking on charge. (iii) Only old unserviceable items will be considered in credit Sch. 129 M&L for Point Wiring for one light Point/one fan point/ one call bell point, controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with continuous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed rigid PVC conduit(ISI marked) ,duly cutting chases & concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia(Color coding of wires shall be Phase, neutral and earth wire all as specified ) including metal flush box made of GI sheet and white cover with making good the disturbs surfaces of wall/floor/ceiling complete all as specified and directed for the following.Note: Flush box and cover plate should be of same make all as approved for switches/sockets. 130 One light/fan/bell point controlled by one No modular type switch 6 Amps single pole one way 131 One 3 pin 6 Amps socket outlet on same board controlled by one, one way 6 Amps modular switch. 132 One socket outlet 5/3 pin 6 Amps controlled by one modular switch on independent board. 133 All as per item No 104 here-in-above but wiring with 2.5 sqmm single core multi stranded copper condcutor1100 V grade PVC insulated FRLSH but unsheathed single core for16 Amps power point on independent board and 2.5 sqmm FRLSH cable as earthwire. 134 S & F switch Modular single pole,one way 6 Amps , 1 module,230 volts, 50 hzcomplete all as specified and directed. 135 S&F modular switch bell push button type, 1module,6 Amp single pole complete all as specified and as directed. 136 Supply and fix Modular switch 1 way 16 Amps, 1 module, 230 volts, 50 Hz complete all as specified and directed. 137 Supply and fixModular Socket outlet, 6A - 2/3 pin combined, 2 module ISI marked, 230 volts, 50 hz complete all as specified and directed. 138 Supply and fixModular Socket outlet, 16A - 2/3 pin combined, 2 module ISI marked, 230 volts, 50 hz complete all as specified and directed. 139 S&F bell electric DING DONG type,AC, 230V single pole, 2module complete all as specified and as directed. 140 S&F fancy Lamp holder (with metal ring), insulated body, of PVC/ Polycorbonate with back plate (ISI Marked) suitable for batten fitting complete all as specified and as directed. 141 S&F ceiling rose 3 terminal / PVC/ polycarbonate, isolated body complete all as speccified and directed 142 S&F connecting & testing distribution board of sheet metal enclosures double door, IP-43, 240V, for using MCBs / MCB isolators with having tinted copper bus bars suitable for 200 Amps ratinghaving following capacity complete all as specifiedanddirected 143 DB SPN, 8 way 144 DB SPN, 12 way 145 S&F MCB DB TPN 4 Way connecting & testing distribution board of sheet metal enclosures double door,415 volts rated copper bus bars suitable for 200 Amps ratinghaving following capacity complete all as specifiedanddirected 146 S&F MCB , SP, AC, 240 volts of 06 to 32Amps capacity 10KA, "C" series and making connections with suitable size of copper lugs complete all as specified & directed. 147 S&F MCB, SPN, AC, 240 volts of 40 Amps capacity 10KA, "C" series and making connections with suitable size of copper lugs complete all as specified & directed. 148 S&F MCB, TPN, AC, 415 volts of 63 Amps capacity 10KA, "C" series and making connections with suitable size of copper lugs complete all as specified & directed. 149 S&F surface mounted LED luminiare, 10 watt2 feet with all accessories having polymer extruded channel with diffuser for glare free light, high lumen output, driver PF >0.98 having over voltage protection upto 400 volts surge protection, level 7-10 KV thermal short circuit protection THD<10%, made up of long life LED chips (SMD) in modular with Ra>70 and lumen efficiency >120 lumen per watt, internally pre-wired through flexible wire connecting with ceiling rose complete all as specified and directed.Note: The firm has to give warranty for fitting including driver minimum for 2 years for any defects developed during the period. 150 S&F surface mounted LED luminiare, 20 watt4 feetwith all accessories having polymer extruded channel with diffuser for glare free light, high lumen output, driver PF >0.98 having over voltage protection upto 400 volts surge protection, level 7-10 KV thermal short circuit protection THD<10%, made up of long life LED chips (SMD) in modular with Ra>70 and lumen efficiency >120 lumen per watt, internally pre-wired through flexible wire connecting with ceiling rose complete all as specified and directed.Note: The firm has to give warranty for fitting including driver minimum for 2 years for any defects developed during the period. 151 S&F LED bulb 10 watt (Cool day light) having colour temp 6500 K and lumen out put 950 suitable for B-22 type to fix on batten holdercomplete all as specified anddirected. 152 S&F sub main wiringtwo single core6 Sqmm PVC insulated, unsheathed, stranded copper conductor cable(FRLSH) 1100Volts grade drawn in & including rigid PVC Conduit 20 mm dia or more medium grade concealed in wall along with 6.00 Sqmm PVC insualted unsheathed copper conductor cable (FRLSH) as earth wire andwire connected with main earth dolly including cutting chases and making good disturbed portion complete all as specified and directed. Note : Two runs of phase, neutral wire and one run of earth wire and PVC conduit will be measured as one RM or one length. 153 S&F in repair Exhaust fan plastic body AC single phase 230 Volt of size 300 mm sweep complete with blade, Frame and louvers including making hole and grouting of nut bolts etc and making good the disturbed sufaces of wall complete all as specified and directed. Old Exhaust fan to be deposited in MES Store 154 M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground levelat any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate. connected by 4mm GI Wirecheck nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI strip upto 7.5 mtrs long with 15 mm dia medium grade GI pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing strip to panel, including testing on completion complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighing not less than 4kg/sqm in lieu of CI cover.(ii) Cost of additional GI strip more than 7.5 mtrs will be measured and paid seperately under relevant items. 155 S&F recessed mounted LED light fitting 36 watt, 230V, 2"x2", with diffused acrylic cover with all accessories having high lumen output, driver PF>0.98 having over voltage protection upto 400 V, ISI marked square lit panel 2x2 LED luminaire with diffuser 3 core with flexible copper cable PVC insulated of size 1.5 Sqmm complete fixing on existing false ceiling/ POP ceiling/ Armstrong ceiling/ Grid ceiling and required cutting of any type of ceiling to fix the light and making good as peer existing ceiling included on quoted rates, necessary T&P like hydraulic ladders or normal ladders for fixing height upto 4.5 mtrs arranged by contractor on own arrangement is included on quoted rate the light id to be fixed on buildings like Auditorium, Arty mess Gym, Officer transit mess etc complete all as specified and directed 156 S&F earth continuity conductor or main earthing lead fixed to walls or to poles or any other indicated situation for loop earthing with using 4mm dia GI earth wire complete all as specified and directed. 157 S&F OFF load change over switch 415 V in sheet metal enclosure 4 pole of capacity 63 Amp complete all as specified and directed. 158 S&F in repair electric water heater ABS body,storage type steel body with stainless steel inner tank with glass line coating and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated, ISI Marked, 240 V, 50 Hzcomplete with all accessories such as safety valve, thermostate, NRV, PVC connection pipe, plug top and including provision of wall mounting arrangement with suitable size of anchor bolts complete all as specified and directed . Old Geyser to be deposited in MES Store
|
