|
Misc Repair B/R And E/M Works And Cleaning Of Sewage Lines Manholes Septic Tanks Including Periodical Services To Md Accn Bldgs And Otm Bldgs At Dad Residential Complex And Aao Shillong Under Ge Shillong; 1 Complete removal of existing treatment on wall/ceiling/concrete surfaces with Washing, rubbing, down and stopping of distempered and painted surfaces 2 M&L for preparation of surfaces and applying putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified. 3 M & L for preparation of surfaces and preparation of surfaces and applying one coat of oil bound distemper with roller on old treated surface of wall/ Ceiling etc complete all as specified and directed. 4 M & L for preparation of surfaces and applying two coat of oil bound distemperwith roller on old treated surface of wall etc complete all as specified and directed. 5 M&Lfor preparation of old decorated plastered surfaces of ceiling and applying one coat of oil bond distemper on ceiling complete all as specified and directed. 6 M & L for preparation of old treated surface of ceiling and applying one coat ofwhite wash completeall as specified and directed. 7 M & L for preparation of old treated wood or wood based surface of any description exceeding 10cm width or girth and applying one coat of synthetic enamel paintcomplete all as specified and directed. 8 M & L for prepration of old treated steel surface of any description exceeding 10cm width or girth and applying one coat of synthetic enamelled paint complete all as specified and directed. 9 M&L for preparation of old decorated surface on wall and applying one coat ofExterior emulsion paint ( weather coat), complete all as specified and directed. 10 M&L preparation of old painted steel roof surfaces, over 10cm in with or girth and applying one coat of synthetic enamel roof paint complete all as specified and directed. 11 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises. 12 M&L for light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4 complete all as specified and as directed 13 M&L for light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to matchover 10mm thick rendering in CM 1:4 complete all as specified and as directed 14 M&L for Non skid joint free ceramic tiles, 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etcset and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colourover 15mm thick screed bed in CM 1:4 complete all as specified and directed 15 M&L for Non skid joint free ceramic tiles, 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting etcset and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colourover 10mm thick rendering in CM 1:4 complete all as specified and as directed 16 M&L for Glazed ceramic coloured tiles in vertical surface of size 300x450mm, 7-8mmthick setand jointed in neat cement slurry and pointed in white or colour cement to match with thetile colour over 10mm thick backing coatin CM 1:4 complete as specified and directed 17 M&L for Non skid joint free ceramic tiles, 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etcset and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colourover 15mm thick screed bed in CM 1:4 complete all as specified and directed 18 M&L for outdoor coloured vitrified paving tiles, joint free(edge cut) of size 300x300x8 to 10mm thick as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in cement sand mortar 1:4 complete all as specified and as directed 19 M&L for outdoor coloured vitrified paving tiles, joint free(edge cut) of size 300x300x8 to 10mm thick as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement over 10mm thick rendering in CM 1:4 complete all as specified and as directed 20 Demolition of PCC (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed. 21 M&L 100 mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate as in hard standing finished even and fair laid in alterrnate bays of size not exc 2 m X 2m with construction joints and filled with joint sealing compound complete all as specified and directed. 22 M&L for PCC 1:3:6 type C2 (using 40mm graded aggregate) 100mm thick as in sub base, paving etc finished even and fair complete all as specified and directed. 23 M&L Machine pressed precast concrete polished interlocking paver block any shape and size of approved design confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed. 24 M&L of sand filling under floors or in foundation including watering and consolidation complete all as specified and directed. 25 M&L 75mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in plinth protection/hard standing finished even and fair with 10 mm joint filled with bitumen mastic (mix of bitumen and sand at 3m intervals complete all as specified and directed. 26 Dismantling of plain or corrugated AC/ steel /fibre glass reinforced transluscent sheeting any guage thickness including nainital or similar pattern roof covering complete all as specified and directed. 27 S&F pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick having tensile strength 550 Mpa as in roof covering / cladding to wall including fixing with self tappingscrews washers, profile, shape and colour as approved by GE, complete all as specified and directed. 28 S&F pre-painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick having tensile strength 550 Mpa as in roof covering / cladding to wall including fixing with self tappingscrews washers, profile, shape and colour as approved by GE, complete all as specified and directed. 29 Dismantling wrought iron or mild steel work of any description not otherwise provided for. 30 M&L for roof truss ( framed), trussed , purlin etc. of angle or other section for fixing of sheets and similar works complete of Gde Fe-290(Gde E-165) . 31 M&L for prepration of new steel surface of any description over 10cm in width or girth and applying two coat of synthetic enamel paint over one coat of red oxide/ zinc chrome primer complete all as specified and directed. 32 Excavation in post holes not exc. 0.5 cum, getting out returing, filling in and ramming earth and broken hard core/rubble mixed with earth with around the layers not exiding 25 cm each layers watering and removing surplus soil to a distance not exceeding 50 cm making good complete in soft/loose soil. 33 M&L forPCC (1:3:6), type C1 (using 20 mm graded stone aggregate) as in foundation filling and mass concrete including all necessary form work complete all as specified and directed. 34 Removing existing water proofing treatment along with PVC sheetsdisposing off MoD premises and renderingand carry out the following works for roof treatment a) 15mm thickin CM 1:4 screed bed by hacking out the existing roof slab.b) Cleaning of plastered roof surface andapplying one coat of cold bituminous primer@ 0.25ltrs per sqm confirming to IS:3384- 1986.c) A layer of APP based polymericmembrane 3mm thick (minimum) weighing3.5kg/m² reinforced with polyester nonwoven fabric (weighing not less than 160gms/sqm) shall be applied over bituminousprimer. Application of APP membraneoverprimer shall be done by torchapplication. The overlap shall be minimum100 mm on the transverse direction and75mm on longitudinal direction.(iv) Applying one coat of aluminum paint over the APP modified membrance @ 0.11Kg/sqm. (NOTE:- The work of water proofing treatment shall be got executed through expert team of manufacturers or authorised applicator of manufacturer contractor shall be submitted documentary evidence in support of applicator engaged for approval of GE.) 35 Dismantling of wall/ceiling boards (fibre, pulp,insulation, etc.) or insulation boards/ slab/blankets, any thickness including cover fillets complete all as specified and directed. 36 S&F Anodised Aluminiumframe work for snap grid false ceiling comprising of Gl perimeter channnel 0.55 mm thick with Aluminium main T- flange of 25 mm and web of 30 mm fixed to surrounding wall angle with flange and web 25 mm each , Cross T with flange 25 mm and web 25 mm fixed to mainT, Main T is suspended from soffit @ 1200 mm c/c using Gi wire of 4mm thickness, Aluminium frame will be 60cm x 60 cm to recieve ceiling board complete all as specified and directed. 37 M&L for 4mm thick E - boards 600 mm x600 mmprepainted fibre boards ceiling designer/decorative type with different designs as approved by the GEfixed or laid in ceiling timber /GI/ aluminiumframe work in ceiling flat or sloping complete all as per manufacturer instruction complete all as specified and directed. 38 Taking down chowkhat with shutter (without taking off shutter from the frame) and area exc 1.5 sqm but n.exc 4 sqm each complete all as specified and directed. 39 Taking down chowkhat with shutter (without taking off shutter from the frame) and arean.exc 1.5 sqm each complete all as specified and directed. 40 Taking down shutters of any description exc 1.0 sqm but n. exc 2.0 sqm each complete all as specified and directed. 41 Taking down shutters of any description n. exc 1.0 sqm each complete all as specified and directed. 42 S&F 2nd class hard wood plain, solid, straight chawkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. 43 S&F 30mm thick flush shutter solid core construction with block board core and plywood face panels, decorative face veneer with lipping/frame to matchon both sides complete all as specified and directed.. 44 S&F 2nd class hard wood glazed and skeleton shutters, 35mm thick, open rebated & prepared to receive wire gauge (with sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitread beads for securing glass etc, sizes of members of shutters as specified in SSR Pt-I, section 8, clause 8.24- (a), supplied and fitted to chowkats. 45 M&L 30mm thick 2nd class hard wood factory made glazed and skeleton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebatedsash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) complete all as specified and directed. 46 S&F solid PVC door frame of size 50 mmx 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube as per specifiecation complete 47 S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with single piece extruded pvc profile both side prelam PVC sheet "C" channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and 5mm thick both side prelam single piece extruded pvc profile for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of both side prelam5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and shown on drawing given in SSR Part II. The width of stiles & rails shall be in proportion to the width of the door shutter as given in SSR Part I. 48 S&F 18/19 mm thick block boardsfixed with screws to timber frame complete all as specified and as directed 49 S&F 0.90 mm thick PVC decorative laminates type 1 of surface finish color and pattern as approved fixed with approved adhesive as per manufactures instruction complete all as specified 50 M&L for 18/19 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice laminations and other side balancing white lamination fixed with screws as in cabinet / cup-board completed all as specified and directed. 51 S&FContinuous (Piano) hinges, brass, width of flaps 30 mm (when open) complete all as specified and directed. 52 S&F in repairMagnet catches for cupboard shutter, brass body and striking plate including letting incomplete all as specified and directed. 53 S&F brass 150 mm long barrel tower bolts with cast or sheet barrel and rolled or cast bolts and fixed complete 54 S&F extruded fancy type Brass handles fabricated type of size 100 mm completre 55 S&F 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed 56 S&F extruded aluminium alloy handles fabricated type anodisedof size 150 mm completre 57 S&F aluminium anodised barrel bolts and fixed of 100 mm length complete all as specified and directed. 58 S&F butt hinges 100 mm medium weightmild steel cold rolled and fixed 59 S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165all as specified and as directed 60 S&F Mild steel sliding door bolt, plate type stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, length of bolt 300mm complete all as specified and directed. 61 S&Ffloor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified and directed. 62 S&F in repair 300mm long MS Helical door spring Welded to steel /Fixed to wooden door frame including roller and roller plate etc of approved quality complete all as specified and directed. 63 Supply and fixing 4 lever Brass Mortice lock, vertical type 100mm length complete all as specified and directed. 64 Hacking out old broken glass (any thickness, size, quality or description) from wooden frame including taking out old wooden beads complete all as specified and directed. 65 S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in square n exc 0.5 sqm in each pan complete all as specified and directed. 66 S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples. 67 S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples. 68 S&F in repair 25 mm dia aluminium drapery rod with wooden finish, decorative, including brackets, decorative finials at both ends(minimum) in one opening complete all as specified and directed. 69 S&F in repair 600mm x 450mm beveled edge mirror of selected quality, glass 5mm thick, mounted on 6mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. 70 S&F in repairs Vitreous China Wash Hand Basins, size 550 X 400 mm (Flat Back or Angle Back type) including Pillar Taps 15mm Bore Cast Copper Alloy with Capstan Heads, Chromium Plated, fancy type, 32mm dia Brass Chromium Plated Waste Fitting and PVC connection pipe of 15mm x 600mm long, a Pair of Angle iron Brackets duly Painted/Erecting Stand including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed .Make:- Prayag /Hindware/Cera 71 S&F in repair Water closet Pedestal pattern, white (excluding fixing bolts, flushing cistern and flush pipe) including plastic water closet seat, white/black, closed pattern with flat bottom and cover and mild steel chroimum plated or aluminised hinging device complete all as specified and directed. 72 S&F in repair Vitreous china squatting pan, "Orissa" pattern, size 580 X 440 mm white, with integral foot rests including provision of lime concrete bedding, fixing of flushing cisterncomplete all as specified and directed. 73 S&F in repair Health faucet (ABS Body) mild steel chroumium plated suitable for 15mm dia pipe with 1.25metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. 74 S&F in repair PVC valveless, syphonic action type flushing cistern,low level, white, 10 Ltr capacity with inlet, ball valve, float and handle including bracketscomplete all as specified and directed. 75 S&F in repair Bip tap, chromium plated, 15mm fancy type,complete all as specified and directed. 76 S&F in repair Angular stop cock, fancy type, chromium plated, 15 mm bore complete all as specified and directed. 77 S&F in repairs PVC connections 15 mm size with PTMT nuts of length 450mmcomplete all as specified and directed. 78 S&F in repairs Brass Basin mixture CP mixer for mixing hot or cold water screwed down for iron pipe and fixed complete all as specified and directed. 79 S&Fin repairs CP wall mixer non telephonic complete all as specified and directed. 80 S&F Stainless steel kitchen plate rack of size 31" X 30"" X 10" made out of stainless steel sheet of 1.00 mm with all accessories including taking down old unservicable rack . 81 S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs washers and wastes incl bedding in CM to dwarf wall or incl fixing cantilever brackets and connecting union to pipe overall size 915x460 mm bowl size 410mmx360mmx160 mm complete 82 S&Frotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 1000 Ltrs incl taking down old unservicable tank of any description and in any position complete all as specified and directed. 83 S&Frotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 500 Ltrs incl taking down old unservicable tank of any description and in any position complete all as specified and directed. 84 Taking up or down steel tubing and connections for 15 mm bore of pipes complete all as specified and directed. 85 Taking up or down steel tubing and connections for 20 mm bore of pipes complete all as specified and directed. 86 S&F GI steel tubing medium grade 15mm bore with all fitting and fixed complete to wall and ceiling or laid under in floor complete all as specified and directed. 87 S&F GI steel tubing medium grade 20mm bore with all fitting and fixed complete to wall and ceilings or laid in floors complete all as specified and directed. 88 S&F in repairs Gunmetalgate20mm valve class I (ISI)markedwithironwheelhead,screwedbothendsforironpipe, suitablefor pipe complete all as specified and directed. 89 S&F in repairs PVC (SWR) 110 mm bore pipes single socketed in any length with rubber ring joints, fixed to walls/floor including necessary sockets, fitting and clamps for securing pipe complete all as specified and directed. 90 S&F in repair PVC (SWR) 75mm dia pipessingle socketed in any length with rubber ring joints fixed to walls/floor including necessary sockets, fitting and clamps for securing pipe complete all as specified and directed. 91 S&F in repairs PVC (SWR) bend with access door of any radius 110mm bore complete all as specified and as directed. 92 S&F in repairs PVC (SWR) bend with access door of any radius 75 mm bore complete all as specified and as directed. 93 S&Fin repair 75mm dia PVC (SWR) floor trap with CP grating including jointing with solvent cementto pipe complete all as specified and directed. 94 M&L for taking down of existing sunken slab treatment form the sunken portion and cleaning the surfaces by washing down with water and rubbish off the premises.(a) Cleaning and filling cracks with sealing compound, brushing neat with neat cement slurry @ 3.00 kg/ sqm and grouting in 25 mm thick plain cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) over sunken slab portion and finishing the top surfaces even and smooth without using extra cement .(b) M&L for two coats of acrylic cementitious water proofing coating (Dr Fixit pidifin 2K manufactured by M/s Pidilite industries Ltd or equivalent make as approved by GE) and followed by a overlay protective 15 mm thick screed/ rendering in CM 1:3 along with liquid water proofing at appropriate ratio of approved make on top surfaces of sunken slab after preparations as mentioned above.Method of application for acrylic cementitious water proofing coating is followed as per manufacturers instructions.(Note : Cost including the lean concrete 1:4:8 for sunken portion area wheredemolition/dismantling carried out to the sunken floor.) 95 Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth and getting out in soft/ loose soil for foundation etc. complete all as specified and directed. 96 Returning, filling in, including spreading, leveling, watering and well ramming in layers n. exc. 25cm in soft/loose soil complete all as specified and directed. 97 Removing excavated soils to a distance n. exc. 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed. 98 Demolition and breaking up drain pipes 150 mm bore (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed. 99 Demolition and breaking up drain pipes 100 mm bore (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed. 100 M&L Salt glazed stoneware drain pipes 150mm internal diameter of pipe laid in trenches and jointed as specified complete all as specified and as directed. 101 M&L for Concrete bed to160mm drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested 102 M&L for Concrete bed to100mm drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested 103 M&L for Concrete bed to110mm drain pipesincluding packing under and completely surrounding pipes with concrete after they are laid and tested; in ® 104 Cleaning of sewage lines using split Bamboo with a gunny bag piece tied with binding wire and inserting the bamboo in sewage lines through manhole/gully trap clear flow of sewage is observed of 100/150/200 mm bore pipe complete all as specified and directed. 105 Dewatering and taking out/ removing sludge waste / foreign materials from septic tank using mechanical pump and disposal of raw water/effluent sludge/waste/foreign material by burying under ground borrow pit of suitable size and covering the pit with earth or earth mixed rubbish with spreading bleaching powder @ 1 kg per pit for disinfection purpose and removing surplus soil to a distance n.exc 50 m complete all as directed by Engr-in-Charge.Note: Measurement of sludge (Solid/Semisolid) shall be taken after draining out of effluent/water over the accumulated sludge and cost of earthwork in excavation for earth pit and spreading of bleaching powder shall deemed to be included in the unit rate quoted by tender against these item. 106 Cleaning of manholes depth n.exc 1.50 mtr each, with spades or bucket, taking out sludge from manhole and disposed off aside by burying the entire sludge under ground in a earth pit dug of suitable size by putting earth mixed with rubbish in it and spreading bleaching powder surrounding the pit and again using water with bucket and put into manhole to clear the sludge and ensure the sludge is drain out completely etc complete all as specified and directed.Note: Cost of earth work in excavation for borrowing the pit and removing surplus soil to a distance n.exc 50m and spreading of bleaching powder around and over the pit shall be deemed to be included in the rate quoted. 107 Cleaning of CI/RCC/PVC pipes of any dia from first floor to ground floor up to trap and 1st manhole along the wall, floor, including roding and removing waste material to a distance not exceeding 50mtr all as directed by Engr-in-charge. 108 M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-l smooth finished, and reforming benching as required for 100 mm internal dia of pipe complete all as specified and as directed 109 M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-l smooth finished, and reforming benching as required for 150 mm internal dia of pipe complete all as specified and as directed 110 M&L 100mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in , sub-base for manholes finished even and fair or even and rough as reqd complete all as specified and directed 111 Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. 112 M&L for precast RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in cover slabs, shelves and similar articles set in CM (1:6) including necessary form work complete all as specified and directed. 113 M&L for Mild steel TMT deformed bars, 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed. 114 Demolition of precast concrete block walling built in cement mortar complete all as specified and directed. 115 M&L Precast cement concrete block masonry with solid block exc 10 Cm in width, type C1 (1:3:6) (using 20mm graded stone aggregate) and setting in CM 1:6 complete all as specified and directed. 116 M&L Precast cement concrete block masonry with solid block 10 Cm thick, type C1 (1:3:6) (using 20mm graded stone aggregate) with plain or interlocking joints and setting in CM 1:4 complete all as specified and directed. 117 Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key, scrubbing down with water, etc all as specified and directed. 118 M&L for rendering 15mm thick in CM (1:4) in two coats (10mm and 5mm thick) mixed with water proofing compound with 5mm thick layer on fair faces of brick work or concrete surfaces including finishing the surface even and smooth without using extra cement, complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately. 119 M&L for rendering 10mm thick in CM (1:6) on fair faces of brick or concrete surfaces including finishing even & smooth without using extra cement complete all as specified and directed. 120 Supply only integral Water proofing compound (ISI Mark) complete all as specified and directed. 121 M&L for preparation of new plastered surfaces of wall and applying two coats of cement based paint over a coat of primercomplete all as specified and directed. 122 M&L for preparation of new plastered surface of walls and applying two coats of acrylic distemper over a coat of alkali resistant priming paint over a coat of 1mm thick wall care putty complete all as specified and directed. 123 M&L for preparation of new plastered surfaces of wall and applying two coats of white wash complete all as specified and directed. 124 M&L 18-20 mm thick Granite stone slab (table rubbed and polished) in steps, jambs, pillars, window-cill, cooking plateform and like in cement mortar (1:4) including pointing in white cementcement with admixture of pigment to match the shade of granite stone including grinding and polishing, rounding to edges laid in any position over 15mm thick screed bed in CM 1:4 complete all as specified and as directed 125 S&F in repairs traffic convex safety mirror of 600mm dia having 130 degree of viewing angle made of polycarbonate materia, brim and back holding plate is made of metal/FRB alongwith pole mounted brackets and pole 60mm dia of galvanised steel frimly fixed to the ground by means of PCC 1:2:4 type B-2 (using 40mm graded stone aggregate) in foundation filling (size 50cm x 50cm x 60cm) complete all as specified and directed. 126 Cleaning and removing all scale and dirt, etc, from PVC/RCC/MS over head tanks by using wire brush, bleaching powder or lime etc of required quantity and washing with clean water from tank and from mouths of circulating pipes, etc after Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position of capacity exc 250 nexc 500 ltrs incl writing "TC on -DD/MM/YY" with white synthetic enamel paint with 5 CM font in capital letters complete all as specified and directed.. 127 Cleaning and removing all scale and dirt, etc, from PVC/RCC/MS over head tanks by using wire brush, bleaching powder or lime etc of required quantity and washing with clean water from tank and from mouths of circulating pipes, etc after Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position of capacity exc 500 nexc 1000 ltrs incl writing "TC on -DD/MM/YY" with white synthetic enamel paint with 5 CM font in capital letters complete all as specified and directed.. 128 Taking down carefully aluminium/copper conductor point wiring (light,fan,socket or power) completeincluding fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing(except those to be reused shall be kept in safe custodyat the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified. 129 Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked,including 20 mm diaPVC conduiton wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductorgreen colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild galvanised sunken box/metal flush box made out of 1.6 mm thick galvanised sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer bothinternally and externally includingaccessories including cutting chasesand making goodthe disturbed surfaces as per existingfor one light point controlled by one switch complete all asspecified anddirected by Engr-in-charge. 130 All as per item No.129 above but One 3 pin 5 Amps socket out let points on independent board 131 All as per item No. 129 above but5 Amp socket on same boardwith other switches. 132 All as per item No. 129 above butOne call Bell point controlled by one bell Push on independent Board 133 Material and labour point wiring for one light point controlled by one, Two wayswitch using1.5 sqmm nominal cross sectional areamultistrandedcopper conductor ,PVC insulated unsheathedFRLSH cables in and including suitable size PVC conduit and fittings of medium grade fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectional area multistranded copper conductor FRLSHPVC insulated unsheathed earth wire and connecting to earth dolly andbrass screws, washers etc. ncluding cutting chasesand making goodthe disturbed surfaces as per existing complete all as specified and directed. 134 Material and labour point wiring for power point controlled by one, one wayswitch using2.5 sqmm nominal cross sectional areamultistrandedcopper conductor ,PVC insulated unsheathedFRLSH cables in and including 20 mm width or higher size PVCconduit and fittings of medium grade fitted with chromium plated brass screws & washers and 2.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLSHPVC insulated unsheathed earth wire and connecting to earth dolly andbrass screws, washers etc. ncluding cutting chasesand making goodthe disturbed surfaces as per existing complete all as specified and directed. 135 Supply and fixing submain wiring for DBs/ Power Point,two single core ,4 sqmm nominal cross sectional areamultistrandedcopper conductor FRLSH cable, PVC insulated unsheathed 1100 Volts gradedrawing in and including suitable sizePVC conduit (ISI marked) including 4 sqmm nominal cross sectional areamultistrandedcopper conductor FRLSH cable, PVC insulated unsheathed 1100 Volts grade earthwireincluding taking down old unserviceable onecomplete all as specified. 136 Material and labour forPoint wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked,including 20 mm casing capingPVCon wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductorgreen colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild galvanised sunken box/metal flush box made out of 1.6 mm thick galvanised sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer bothinternally and externally includingaccessories including making goodthe disturbed surfaces as per existingfor one light point controlled by one switch complete all asspecified anddirected by Engr-in-charge. 137 All as per item No. 136 above but One 3 pin 5 Amps socket out let points on independent board 138 All as per item No. 136 above but5 Amp socket on same boardwith other switches. 139 Material and labour point wiring for power point controlled by one, one wayswitch using4 sqmm nominal cross sectional areamultistrandedcopper conductor ,PVC insulated unsheathedFRLSH cables in and including 20 mm width or higher size PVC casing caping and fittings of medium grade fitted with chromium plated brass screws & washers and 4 sqmm nominal cross sectioanl area multistranded copper conductor FRLSHPVC insulated unsheathed earth wire and connecting to earth dolly andbrass screws, washers etc. complete all as specified and directed. 140 Supply and fixing submain wiring for DBs/ Power Point,two single core ,4 sqmm nominal cross sectional areamultistrandedcopper conductor FRLSH cable, PVC insulated unsheathed 1100 Volts gradedrawing in and including suitable sizePVC casing caping (ISI marked) including 4 sqmm nominal cross sectional areamultistrandedcopper conductor FRLSH cable, PVC insulated unsheathed 1100 Volts grade earthwirecomplete all as specified. 141 Supply and fixing modular switch 1 way 6A module 230/250 volt , AC supply,ISI Marked, with cover plate complete all as specified and directed. 142 Supply and fixing modular bell push 1 way 6A module 230/250 volt , AC supply,ISI Marked, with cover platecomplete all as specified and directed. 143 Supply and fixing modular switch 2 way 6A module 230/250 volt , AC supply,ISI Marked, with cover plate complete all as specified and directed. 144 Supply and fixing modular sockets 6A 2/3 pin combined 2 module 230/250 Volts,50 Hz , AC supply, ISI Marked complete all as specified and directed. 145 Supply and fixing modular switch socket sockets 6A 2/3 pin combined 3 module 230/250 Volts,50 Hz , AC supply, ISI Marked complete all as specified and directed. 146 Supply and fixing modular switch socket sockets 6/16A 6 pin combined 3 module 230/250 Volts,50 Hz , AC supply, ISI Marked complete all as specified and directed. 147 S & F Modular cover plate with frame & flush box of 4 modules. 148 S & F Modular cover plate with frame& flush box of 3 modules. 149 S & F Modular cover plate with frame& flush box of 2 modules. 150 Supply & fix ceiling rose surface bakelite 65 mm x 50 mm three terminal suitable for 230 Volts AC 6 Amps complete all as specified. 151 Supply and fix Bell push, flush type, 5 amp complete all as specified and directed. 152 Supply and fix Call Bell, Ding Dong AC. 230 volts, single pole all as directed 153 Supply and fix 18 W LED light fitting wall mounted batten 4"ft ,extruded aluminium housing, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 18 watt,6500/3000K including necessary connection including taking down old unserviceable one complete all as specified and directed by Engr-in-charge. 154 Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 6500/3000K 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size including taking down old unserviceable one complete all as specified and directed by Engr-in-charge. 155 S & F Wall bracket decorative LED fitting with lamp10 Watt complete with necessary connection complete all as specified and as directed by Engr-in-Charge. 156 Supply and fixing in repair round/rectangular shape 12 watt 220 volts Warm/White AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as direcetd by Engr-in-Charge.Note: (i) All fittings must be mentioned CA No. and date of intallationwith permanent marker 157 Supply & fix lamp holder, PVC/polycarbonate type with back plate straight or angular suitable for batten fittings complete all as specified and as directed by Engr-in-Charge. 158 Supply and fix 9 Watt LED bulb including taking down old unserviceable one complete all as specified and as directed by Engr-in-charge. 159 Supply and fix switch piano flush type, single pole , 5/6 Amps, one way complete all as specified. 160 Supply and fix socketoutlets 2 in 1, 3 pin, 5/6 Amps flush type230/240 V complete all as specified and as directed. (For Same Board only) 161 Supply and fix switch socket combination 2 in 1 multipurpose5 pin , (6 Amps ) flush typecontrolled by one switch complete all as specified and directed. 162 Supply and fix switch socket combination5 in 1 , 6 pin , (5/16 Amps ) flush typecontrolled by one switch complete all as specified and directed. 163 Supply and fix in repair security light fittings 35 watts, minimumm system lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete with GI pipe dia 25mmwith all accessories like clamps nut bolts etc. including connected with twin core twisted flexible copper conductor of suitable size including taking down old unserviceable one complete all as directed by Engr-in-charge. 164 Supply and fix Distribution board double door MCB TPN 4 way with IP 43 multiphase outgoing suitable for mounting 63 Amps MCB as incomer with Bus bars, Neutral links complete with all accessories including taking down old unserviceable one including MCBs complete all as directedby Engr-in-Charge. 165 Supply and fix epoxy powder coated sheet metal enclosure for DBs, double door, Single pole and neutral 240 V, 12 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contactincluding taking down old unserviceable one including MCBs complete all as directed by Engr-in-Charge. 166 Supply and fixMCB SP,6 to 32 Amps, "C" series 10kA, 240 Voltsand to be housed in DBs including necessary connection complete all as specified and directedby Engr-in-Charge. 167 Supply and fix MCB SPN 40 - 63 Amps,"C" series 10kA, 240 Volts and to be housed in DBscomplete including necessary connectionall as specified and directedby Engr-in-Charge. 168 Supply and fix MCB TPN 63 Amps,"C" series 10kA, 240 Volts and to be housed in DBscomplete including necessary connectionall as specified and directedby Engr-in-Charge. 169 Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers including enlargement of hole and giving proper finishing including taking down old unserviceable one complete all as specified and directed by Engr-in-charge. 170 Supply and fix exhaust fan, plastic body AC single Phase. 230V of size 250mm sweep with, blades, and frame and louvers including enlargement of hole and giving proper finishing complete all as specified and directed by Engr-in-charge. 171 Material and labour in repair for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate and bentonite powder , using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased inand including 40 mm dia GI "lightgrade" pipe from upper end of earth plate upto equipments,20 dia bore GI pipe "light grade" as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe andPCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as describedin electric plate of SSR Part Iand testing on completion completeall as specified and directed by Engr-in-charge. 172 Taking down unserviceablelights removing carbon /loose connection and making street light/Post top lantern/bollard lightserviceable including necessary T & P all as specified and directed. 173 Supply and fixing of driver for LED luminary suitable for single phase 45 wattscomplete incl taking out of fitting from pole and refixing after repair complete all as per existing specification Make as per fitting fixed at site. 174 Supply and fixing of driver for LED Bollard 09 watt complete incl taking out of fitting and refixing after repair complete all as per existing specification Make as per fitting fixed at site. 175 Supply and fixing LED flood light 70 watt 230 V AC outdoor type with Efficacy > 100 LPW , 10 KV SPD with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp fixed on wall/roof/pole/floor/highmast with the help of nuts, bolts , washers and clamps etc all as directed by Engr-in-Charge 176 Supply & fixingin repair Gate / Post Top lantern LED lights fitting of capacity 40 W die-cast aluminium body, 40 watt LED 3000/5700K and toughened glass complete with all accessoriesincl taking out old unserviceable oneall as directed.
|
