|
Tender For Repair/ Maintenance Of All Type Of Misc Furniture Under Ge (West) Lucknow.; 1 TABLE DINING 4"x2.5" GLASS TOP (FOR ITEMS SER NO1 TO 8)Taking out old unservicable top and Supply& Fixing Top of table 4" x 2.5" x 10mm glass shall be madeofbrown/black complete all as specified and directed. 2 Taking down U/Slegs and S&Fnew legsStainless steel throuh out as per shape and size complete all as specified and shown on drawing . 3 Same as item No. 2buttop long rail front or back complete all as spcified and as shown on drg. 4 Same as item No. 2but top short rail for sides complete all as spcified and as shown on drg 5 Same as item No. 2but Transparent Glass Vacuum Suction Cup size 1.6x2.6x5.6Cm vaccum topcomplete all as spcified and as shown on drg.. 6 Same as item No. 2butBuffers/Rubber Shoecomplete all as spcified and as shown on drg. 7 Provision of Konia (GI Bracket) of size 3" x 3" x3mm thick in between leg and short/long rail of the table fixed with screw to provide more strength complete all as spcified and as shown on drg. 8 Preparation of surface with sand paper after scrubbing and apply two coat of synthetic enamel paintto table including to the parts repaired/replaced under item No 1 to 7 to the required gloss to match with the existing complete all as spcified and as shown on drg. 9 CHAIR AUDITORIUM (FOR ITEMS SER NO 9 TO 14)Taking down old U/S handle and S/F new handle made complete all as specified and directed 10 Taking down old U/S holfast screw and S/F new holfast screw to fix chair auditorium to floorcomplete all as specified and directed. 11 Taking down old U/S push back system and S/F new push back system to fix chair auditorium complete all as specified and directed. 12 Taking down U/S Srl Number and S/F new Srl Number to fix chair auditorium complete all as specified and directed. 13 Taking down U/S Seat and S/F new Seat to fix chair auditorium complete all as specified and directed. 14 Taking down U/S Seat back and S/F new Seat back to fix chair auditorium complete all as specified and directed. 15 DESK SCHOOL TYPE "A" DESK ADULT, DESK 4X6 (FOR ITEMS SER NO 15 TO 25)Taking out U/S 19 mm thick back plank of deskbox and S&F 19MM thick Plank made out of 1st class hard wood teak wood (MP) free from knots, cracks etc. with permissible moisture contents as per the shape and size as exists complete all as specified and as on shown drg. 16 All as per items No 15 but side plank of Size370 x 140mm x 19mm thick complete all as specified and directed 17 All as per items No 15 but Top of size 365x800 mm complete all as specified and directed 18 All as per items No No 15but bottom of size 365x800 mm complete all as specified and directed 19 Taking down U/S legs and supply and fixing new legs made out of 25mm tube legs size as exists complete all as specified and as shown drg. 20 All as per items No 15 but Tube Foot Rest of Size-25mm square tube steelcomplete all as specified and directed 21 Taking down old U/S rubber shoe and S/F new hard rubber shoe complete all as specified and directed as per drg. 22 Taking out existing unserviceable block board from Desk school and provide new HDHMRboard of size 800x455x19 mm thick and screwed to fix complete all as specified and directed as per drg. 23 Taking out unserviceable sides of board from Desk school and supply & fix new sides of HDHMR board of size 380 x 140 x 19 mm thick . complete all as specified and directed as per drg. 24 Taking out unserviceable partition from Desk school & S&F in partition made out of HDHMR board of size 370x120x19 mm thickcomplete all as specified and directed as per drg. 25 Removal of denting of deshaped portion desk fram and panting with two coats of synthetic enamel Olive grey paint over a coat of red oxide primer complete all as specified and directed as shown drg. 26 SETTEE WITH CUSHION (FOR ITEMS SER NO 26 TO 27)Taking down old unserviceable/damaged seatand back foam cushion of settee with Tapestry cloth and S&F new seat and back of foam cushion of size 1800x600x100 mm thick 40 density fully covered with approved quality tapestry clothduly stichedfor setteecomplete all as specified and as shown on drgs. Note :- (i) Cost of Tapestry cloth shall not be less than Rs 400/-per meter .(ii) Cost of Preparation of wooden surface of settee by scrubbing , sand papering to smooth surface and applying two coats of french polish of required gloss is included in the rate quoted . 27 Taking out old unserviceable legs and Supply and fixing new legs ofsize and shape as exists made of Ist class HW teak duly french polished to reqd gloss to match to existing surfaces complete all as specified and as directed.. 28 SOFA SET 5 SEATER WITH CUSHION(DRG NO. FD/MAP II/02, FD-281 & FD-373 .)Taking out old unserviceable seat or back of foam cushion andSupply and fixing new seat or back of foam cushion of size 530x560x100mm 40 densityduly coveredwith tapestry clothof approved qualityduly stiched complete all as specified and as shown on drawing No FD/MAP II/02, FD-281 & FD-373 . Note :Cost of Tapestry cloth shall not be less than Rs 400/- per meter . 29 M&L for taking out old unserviceable tapestry cloth from seat or back of foam cushion andSupply and fixing newtapestry clothof approved qualityduly stiched complete all as specified and as shown on drawing No FD/MAP II/02, FD-281 & FD-373 . Note :Cost of Tapestry cloth shall not be less than Rs 400/- per meter . 30 TABLE 5 x 2 - 10/TABLE DINING OR"SFD- 165 M (FOR ITEMS SER NO 30 TO 35)Taking down old u/s top and S/F New top made by 18/19mm thick HDHMR Board exterier gradewith 22 gauge aluminium sheet on around the top shall be provided complete all as specified and directed 31 Taking down old unserviceable legs and Supply and fixing legs of size 720mm, 25mm bore madeof 16 gaugeMS conduit pipe throughoutwith shape and sizeas exists complete all as specified and as shown on drg . 32 All as per serialitem No 30 above but centre stiffner size 1600x25 x25mm complete all as specified and directed 33 All as per serial item No 30above but side stiffener size 480x25x1.6mm complete all as specified and directed 34 Welding of cracked joints on frame ,derusting, cleaning of old surface of frame with & including parts/ item repaired/replaced under item No 31 to 33above and applying two coats of white synthetic enamel paint over a coat of red oxide primer complete all as specified and as shown on drg . 35 Taking downold unserviceable shoe and Supply and fixing newshoe of PVCto legs complete all as specified and as shown on drg . 36 Cupboard Steel 78x36x19 (FOR ITEMS SER NO 36 TO 43)Taking down/out old unserviceable handle and Supply and fixing chromium plate handle100 mm long complete all as specified and as shown on drg . 37 Taking down/ outold unserviceable lock and Supply and fixing 6 lever ofbrass lock godrej pattern complete all as specified and as shown on drg . 38 Taking down/out old lock cover and Supply and fixinglock cover made of 16 gauge MS sheet complete all as specified and as shown on drg . 39 Taking down /out old worn out legs and Supply and fixing oflegs made of 18 gauge of MS sheet complete all as specified and as shown on drg . 40 Taking down old unserviceable hanging rod and Supply and fixinghanging rod20 mm bore mild steel chromium plated made of 1 mm thick conduit pipe , 915 mm long with both side steel socket complete all as specified and as shown on drg . 41 Taking down/out old unserviceable shelves and Supply and fixing shelves made of MS plain sheet 1mm thick complete all as specified and as shown on drg . 42 Taking down/out old unserviceable door shutter and Supply and fixing new door shutter made of MS plain sheet 1mm thick shape and size complete all as specified and as shown on drg . 43 Removal ofdenting for thedeshaped portion of cupbaord steel , cleaning of rusted surfaceswith & including parts/ item repaired/replaced under item No 38to 42aboveincluding preparation of patches by applying putty etc and applying one coats of paint AD grey/Olive green synthetic enamel on theinternal surfaces and hammer tex /Olive green synthetic enamelon the external surfaces by spray gunover a coat of red oxide primer complete all as specified and as shown on drg. 44 Cupboard Steel 50x30x17 (FOR ITEMS SER NO 44 TO 51)Taking down/out old unserviceable handle and Supply and fixing chromium plate handle100 mm long complete all as specified and as shown on drg . 45 Taking down/ outold unserviceable lock and Supply and fixing 6 lever ofbrass lock godrej pattern complete all as specified and as shown on drg . 46 Taking down old cleats and supply and fixing new cleats complete all as specified and as shown on drg . 47 Taking down/out old MS Round bar 8mm fixing with lock upper bar and below bar and Supply and fixing of MS Round bar 8mm fixing with lock cover upper and lowercomplete all as specified and as shown on drg . 48 Taking down /out old worn out legs and Supply and fixing oflegs made of 18 gauge of MS sheet complete all as specified and as shown on drg . 49 Taking down/out old unserviceable shelves and Supply and fixing shelves made of MS plain sheet 1mm thick complete all as specified and as shown on drg . 50 Taking down/out old unserviceable door shutter and Supply and fixing new door shutter made of MS plain sheet 1mm thick shape and size complete all as specified and as shown on drg . 51 Removal ofdenting for thedeshaped portion of cupboard steel , cleaning of rusted surfaceswith & including parts/ item repaired/replaced under item No 46 to 50aboveincluding preparation of patches by applying putty etc and applying one coats of paint AD grey/Olive green synthetic enamel on theinternal surfaces and hammer tex /Olive green synthetic enamelon the external surfaces by spray gunover a coat of red oxide primer complete all as specified and as shown on drg. 52 Book Case with Glazed Steel /Almirah Large with Glazed shutter steel (FOR ITEMS SER NO 52 TO 59)Taking down/out old unserviceable handle and Supply and fixing chromium plate handle100 mm long complete all as specified and as shown on drg . 53 Taking down/ outold unserviceable lock and Supply and fixing 6 lever ofbrass lock complete all as specified and as shown on drg. 54 Taking down /out old worn out legs and Supply and fixing oflegs made of 18 gauge of MS sheet complete all as specified and as shown on drg . 55 Taking down/out old unserviceable shelves with cleat and Supply and fixing shelves with cleat made of MS plain sheet 1mm thick complete all as specified and as shown on drg.. 56 Taking down/out old unserviceable door shutter and Supply and fixing new door shutter made of MS plain sheet 1mm thick shape and size complete all as specified and as shown on drg . 57 Taking down/out old unserviceable glass 5mm from Door shutter frame and new glass 5mm thick fitted with door shutter complete all as specified and as shown on drg. 58 Taking down out old Roller/hinges(ISI Marked) from the shutters of book case and fix new roller/hinges all as specified on drg. 59 Removal of denting for the deshaped portion and scraping of complete old paint by paint remover OR sand paper of Book case , cleaning of rusted surface with including parts/item repaired / replaced under items No 54 to 58 above.Including preparation of surface by applying putty and applying one coat of paint AD Gray /olive green synthetic enamel on the internal surfaces and hammer tex/olive green synthetic enamel on the external surface by spray gun machine over a coat of red oxide primer complete all as specified and as shown on drg. 60 CHAIR EXECUTIVE REVOLVING/CHAIR REVOLVING: (For Item No60 to 67) Taking downU/S updown lever and S & F Up Down adustable lever with size and shape exists complete all as specified as shown on drg. 61 Taking out U/S back and S & Fback of chair executive revolvingwith size and shape exists complete all as specified as shown on drg. 62 Taking out U/S seat andS & F seat of chair executive revolving with size and shape exists complete all as specified as shown on drg. 63 Taking out U/S hydraulic jack for and S & F seat of chair executive revolving with size and shape exists complete all as specified as shown on drg. 64 Taking out U/S regin/ tapestry cloth of seat and S & F tapestry cloth on seat of chair executiveapproved quality duly stiched complete all as specified on drawing 65 Taking out U/S coaster wheel and S & F coaster wheel of twin of executivechair with size and shape exists complete all as specified as shown on drg. 66 Taking out U/S hand rest and S & F hand rest of twin of executivechair with size and shape exists complete all as specified as shown on drg. 67 Taking out U/S Pedestal assy and S & F of new Pedestal assy injection moulded in black 30% glass filled nylon10.5mm dia forged bright zinc plated MS castor pin of press fitted to each prong for holding the castors. 68 TABLE DINING 8 PERS DRG No FD/MAP-II/03 (For Item No 68 to 73)Taking out old unservicable top and S&F Top of table madeof 18/19 mm prelaminated HDHMR board exterior grade, 2 mm plastic beading covered all round the top complete as specified and as shown on drg 69 Taking down U/S legs and S&F legs of size 90x45mm front/rear left/right made of 1st class seasoned teak wood free from knots and cracks with permissible moisture contentsthrouh out as per shape and size complete all as specified on drawing and directed at site. 70 Same as item No. 68 buttop long rail front or back complete all as spcified and as shown on drg. 71 Same as item No. 68 but top short rail for sides complete all as spcified and as shown on drg.. 72 Provision of Konia (wooden Bracket) of size 4"x3" seasoned teak wood 1" thick in between leg and short/long rail of the table fixed with screw to provide more strength complete all as spcified and as shown on drg. 73 Preparation of surface with sand paper after scrubbing and apply two coat of Malamine Polish glossy finish to table withdrawers with and including to the parts repaired/replaced under item No 68 to 72to the required gloss to match with the existing complete all as spcified and as shown on drg. 74 DISPLAY BOARD (1830MMX1220MMX760MM Drg No - 99 (M) (74 TO 81) Taking down old U/S Sidesrail /beading and S&F new sides 25mmx40mmx 3mm made of 1st class seasoned teak wood free from knots and cracks with permissible moisture contentsas per shape and size complete all as specified on drawing and directed 75 Same as item No. 74but Top long rail/beadingcomplete all as specified and shown on drg. 76 Same as item No. 74 butBottom long rail/beadingcomplete all as specified and shown on drg. 77 Same as item No. 74 but back side bottom to top stiffner complete all as specified and shown on drg. 78 Taking out U/S Green baize cloth of notice boardand S & F Green baize clothon display board approved quality duly installed complete all as specified on drawing and directed 79 Removal of broken glass panel and new glass pane of size 5mm thickduly slotted glass for sliding purpose complete all as specified and directed 80 Taking out old unserviceableback plyand S&F new 12mm thickplywood of size 1830mmx1220mm760mm 12mm ply wood thick complete all as specified and directed 81 Preparation of surface with sand paper after scrubbing and French polishing to Display boardunder item No 74 to 80to the required gloss to match with the existing complete all as spceified and as shown on drg. 82 TABLE CONFERENCE(For Item No 82 to 87) Taking out old unservicable top and S&F Top of table shall be madeof 18/19 mm prelaminated HDHMR board exterior grade, 2 mm plastic beading covered all round the top complete as specified and as shown on drg 83 Taking down U/S legs and S&F legs of size 90x45mm front/rear left/right made of 1st class seasoned teak wood free from knots and cracks with permissible moisture contentsthrouh out as per shape and size complete all as specified on drawing and directed at site. 84 Same as item No. 82 buttop long rail front or back complete all as spcified and as shown on drg. 85 Same as item No. 82 but top short rail for sides complete all as spcified and as shown on drg.. 86 Provision of Konia (wooden Bracket) of size 4"x3" seasoned teak wood 1" thick in between leg and short/long rail of the table fixed with screw to provide more strength complete all as spcified and as shown on drg. 87 Preparation of surface with sand paper after scrubbing and apply two coat of Malamine Polish glossy finish to table withdrawers with and including to the parts repaired/replaced under item No 82 to 86to the required gloss to match with the existing complete all as spcified and as shown on drg. 88 TRESTLE STORE ROOM WOODEN (DRG NO- FD-86M) (For Item No 88 to 92) Taking out old U/S legs and S&F new legs of size 405x100x100mm made out of second class HW (Sal) complete all as specified and shown drg. 89 All as per item ser No, 88 buttop rail of size 2440 x100 x100 mm complete all as specified and directed 90 All as above ser No. 88but middle of size 600x100x60mm complete all as specified and directed 91 All asitem No 88 but verticals of size 2040x100x60mm complete all as specified and directed 92 Prepartation of surface with sand paper after scrubbing and applying two coats of cresote oil with and including to the parts repaired/replaced under item No 88 to 91, to make smooth surfaces to match with the existing complete all as specified and directed 93 TABLE BED SIDEDRG No : FD/E6/MAP/15® , FD-28 & FD-276: :(For Item No 93 to 99) Taking down old unservicable top and S&F new Top of table bed side shall be madeof 18/19 mm prelaminated HDHMR board of exterior 2 mm plastic beading covered all round finish complete all as specified and directed 94 Taking out U/S upper drawer and S & F upper drawer made of 12 mm thick ply, BWRgrade with complete all as specified and directed 95 Taking out U/S MS legs and S & F MS legs of size and shape exists all as complete all as specified and directed 96 Taking out U/S lower drawer and S&F of lower drawer complete all as secified and as shown on drg 97 Taking out old u/s stiffner and fixing of new stiffner made of 1st class seasoned teak wood free knots and cracks with permissible moisture contents size 400mmx 50mm x25MM complete all as specified and directed 98 Taking down U/S handle and S & F handle and shape exists all as complete as specified as showm on Drg. 99 Scraping of old painting with sand paper/Grinder and prepare surface to apply two coat of black paint and polishing glossy finishrepaired /replace under item No 93 to 98 to the required gloss and colour as directed 100 HARD BED STEEL DRG No FD/MAP/E6/08 (R) : (For Item No 100 to 107)Taking down old unserviceable Ply Top and S & F New Ply top made of 12 MM thick commericial BWR Plywith the help ofscrew as reqd ISI : 303 complete all as specifed and as shown on drg 101 Taking out unserviceable head board and S & F new head board made of 18/19 MM thick both side pre lamineted HDHMR Board of exterior gradeand including 4mm thick teak wood beading alround with size and shape all as per specified and as shown on drg. 102 Taking out unserviceable foot board and S & F new foot board made 18/19 MM thick both side pre lamineted HDHMR Board of exterior gradeand including 2 mm plastic beading alround with size and shape all as per specified and asshown on drg. 103 Taking out unserviceable long rails of bed hard steel and supply and fixing new longrails made of 25 X65 mmMS Retangular 18 welded with short rails on bed hard steel size and shape all as specified and as shown on drg. 104 Taking unserviceable short rails of bed hard steel and supply & fixing new short rails made of 25X65 mm MS Retangular 18 welded with long rail on bed hard steel size and shape complete all as specified and directed as shown on drg. 105 Taking out unserviceable legs and S & F new legs made of 38 x 38 mm MS square pipe 18 gauge welded with frame of bed hard steel complete all as spceified and shown on drg. 106 Taking out U/S hard rubber shoe and S & F rubber shoe of size and shape all as shown on drg. 107 Preparing of surface with sand paper after scrubbing paint to bed hard steel including all parts repared/repleced under item No 100 to 106 applying two coats of enamled paint over a coat of red oxide primer after cleaning te surface complete all as per specified and as shown on drg. 108 CHARPOY WITH HARD TOP DRG No FD/MAP-II/01 : (For Item No 108 to 113)Taking down old unserviceable Ply Top and supply and fixing New Ply top made of 12 MM thick BWR Grade Ply ISI : 303 complete all as specifed and as shown on drg 109 Taking out unserviceable long rails ofcharpoy MS ply top and supply and fixing new longrails made of 25 X65 mmMS Retangular 18 gauge welded with short rails on charpoy MS ply topsize and shape all as specified and as shown on drg. 110 Taking unserviceable short rails of charpoy MS ply top and supply & fixing new short rails made of 25X65 mm MS Retangular 18 gauge welded with long rail on charpoy MS ply top size and shape all as shown on drg. 111 Taking out unserviceable legs and supply and fixing new legs made of 38 x 38 mm MS square pipe 18 gauge welded with frame of charpoy ms ply top complete all as spceified and shown on drg. 112 Taking out U/S hard rubber shoe and supply and fixing new rubber shoe of size and shape all as shown on drg. 113 Preparing of surface with sand paper after scrubbing paint to Charpoy with hard top including all parts repared/repleced under item No 108 to 112applying two coats of synthetic enamled paint over a coat of red oxide primer after cleaning te surface complete all as per specified and as shown on drg. 114 Table WorkShop Steel for items 114 to 119)Taking out old unservicable top and S&F Top of table shall be madeof40mm thick teak wood / prelaminated HDHMR board exterior grade, ISI MarkedIS-3087-1985 bonded with Phyol Pharmeldihide with one sideteak face and other side white of exterior grade quality including with 4 mm thick teak wood beading all round the top complete as specified and as shown on drg 115 Taking down U/S legs and S&F legs of size 32mm square pipe of 1.6mm wallthickness 760mm front/rear left/right made ofMS tube throuh out as per shape and size complete all as specified on drawing and directed at site. 116 Taking out old U/S top long rail and S&F top long rail front or back complete all as spcified and as shown on drg. 117 All as per item No 116 above but top short rail for sides complete all as spcified and as shown on drg.. 118 Provision of Konia (wooden Bracket) of size 4"x3" seasoned MS Tube 32mm 1.6mmthick in between leg and short/long rail of the table fixed with screw to provide more strength complete all as spcified and as shown on drg. 119 Preparation of surface with sand paper after scrubbing and apply two coat of Malamine Polish on top of beading /paintingreqd on MS Tube sections and including to the parts repaired/replaced under item No 114 to 118to the required gloss to match with the existing complete all as spcified and as shown on drg. 120 CHARPOY GI PIPE PLY TOP FD No 220A: (For Item No 120 to 122)Supply and fixing 12mm thick new ply top size 1980mm x900 mm, BWR grade with 06 x Nos of GI Nut and bolt 3"x6mm & 06 Nos x 1.5"x6mm, ISI marked including taking out old unserviceable ply top complete and tightening and weldingas required on stiffner and L Bracket of all charpoy all as specified and directed. 121 S&F 32 mm bore, heavy duty, 3 way GI elbow, ISI marked having weight not less than 440 gms each including taking out old unserviceable elbow complete all as specified and directed. 122 S&F 32 mm bore, heavy duty, GI checknut hexagonal, ISI marked including taling out old old unserviceable checknut complete all as specified and directed. 123 BIN LINEN MULTIPURPOSE/SIDE BOARD: DRG NO - FD/E6/MAP/09, FD-241, 26M, FD-1112: (For Item No 123 to 132)Taking down U/S legs and S&F new legsof size 50x50x75mm madeof 1st class HW(Teak) well seasoned free from knots and cracks with permissible moisture through out shape and sizecomplete all as specified and shown on drg. 124 Taking out old U/S bottom frame and S&F new bottom frame of size 1060x 290x 25x 45mm complete all as specified and shown on drg. 125 Taking down old unserviceable drawers and supply and fixing new drawer made of 12mm thick ply BWR with size and shape as exists complete all as specified and as shown on drg. 126 Taking down old unserviceable Top and supply and fixing new top made of 18/19 mm thick prelaminated HDHMR Board (exterior Grade). Complete all as specified and as shown on drg. 127 Taking down U/S partition and S&F new partition of HDHMR board of size 610x460mm x18mm complete all as specified and as shown on drg. 128 Taking out old U/S top or bottom and S&F new top or bottom of size 1220x455mmx18mm complete all as specified and shown on drg. 129 Taking down old unserviceable back ply and supply and fixing new ply of size 1220x635mm, 6mm thick commericial BWR grade, IS-303 grade complete all as specified and as shown on drg 130 Allas item No 128 but side of size645 x 455mm complete all as specified and shown on drg. 131 All as per item No. 128 abovebutHDHMR shelf of size 425x770 complete all as specified and shown on drg. 132 Taking down old unserviceable Handle and supply and fixing newHandle 75mm, brass, chromium plated complete all as specified and as shown on drg. 133 Preparation of surface with sand paper after scrubbing and two coats fo french polishing to bin linen multi purpose side board, with and including to the parts repaired/ replaced under item No123 to 132to the required gloss, to match with the existing complete all as specified and as shown on drg. 134 CHAIR DINING LONG BACK /CHAIR DINING OFFRS DRG NO :FD/MAP-II/05 , FD/MAP-II/04, FD-/MAP-II/10 & FD-279 (FOR ITEMS SER NO 134 TO 144) Opening of joints and removing offront leg and S&F new front leg (left/right) made of 1st class seasoned teak wood free from knots and cracks with permissible moisture contents as per shape and size complete all as specified in drawing. 135 Same as item No 134 but rear legs1st class teak wood complete all as specified and shown on in drawing. 136 Same as item No 134but stiffenersize 20x25 mm 1st class teak wood complete all as specified and shown on in drawing. 137 Same as item No 134 but all side rail size 65x25 mm 1st class teak wood complete all as specified and shown on in drawing. 138 Same as item No 134 butnylon buffers complete all as specified and shown on in drawing. 139 Taking out old unserviceable 4MM thick PVC Seat and supply and fixing new 4MM thick PVC seat with holes screwed with rails complete all as specified and directed. (DRG NO FD/MAP-II/05) 140 Supply and fixing new stiffner Size 16"x1-1/2"x1"should be fixed bottom of PVC Seat for support made of 1st class seasoned teak wood free from knots and cracks with permissible moisture contents as per shape and size complete all as specified and directed 141 Taking out old unserviceable cane and supply and fixing new cane weaving with1st quility white cane 2mm H/R shape made out of vergin plastic and 0.6 mm thick as perGodrej pattern complete all as specified and directed (DRG NO 279). 142 Taking out U/S foam of chair dining and S&F new 75 mm thick 32 density foam with fabric on seat of 12 mm thick plyBWR Grade duly coveredwith tapestry clothof approved qualityduly stitched complete all as specified and as shown on drawing complete all as specified and directed Note : Cost of Tapestry cloth shall not be less than Rs 400/- per metre . 143 Taking out U/S foam of chair dining and S&F new 75 mm thick 32 density foam with tapestry clothof approved qualityduly stitched complete all as specified and as shown on drawing and driected by Engr-in-Charge. Note : Cost of Tapestry cloth shall not be less than Rs 400- per metre . 144 Preparation of surface with sand paper after scrubbing and French polishing to chair dining and including to the parts repaired/replaced under item No134 to 143to the required gloss to match with the existing complete all as specified and as shown on drg. 145 TABLE DRESSING GENTSWITH MIRROR:( FD 230, FD/MAP/II/16) (For Item No 145 to 154)Taking out existing old unserviceable foggi fadded looking mirror size 1200x550mm x 5mm thick with frame and S&F new looking mirror of same size and shape duly framed with 1st class seasoned teak woodand back of mirror complete all as spceified and shown on drg. 146 Taking down old U/S broken glass panel and S&F new glass pane of size 5mm thickduly slotted glass for sliding purpose complete all as specified and directed 147 S&F new fastner on back of looking mirror for fixing on wallas per shape and size complete all as specified on drawing and directed 148 S&F newhasp and stapleon front of looking mirror for open and close of looking mirror complete all as specified on drawing and directed 149 S&F newhandle 100mm make of Stainless steel on front of looking mirror for open and close of looking mirror complete all as specified on drawing and directed 150 Taking down bottom HDHMR board 18mm of drawers and S&F new HDHMR board 18mmexterior gradegrade ISI Marked,IS-303 gradeas per required size complete all as specified and directed 151 Taking down old U/S sides and S&F new sides of table dressing gents complete all as specified and shown on drg. 152 Taking down of unsv bottom frame and S&F new frame with legs of 1st class seasoned teak wood free from knots and cracks with permissible moisture contains as per shape and size complete all as specified on drawing and directed 153 Taking down of unsv piano type hingesand S&F new piano type hinges complete all as specified on drawing and directed 154 Preparation of surface with sand paper after scrubbing and French polishing to table dressing gents, with and including to the parts repaired/replaced under item No 145 to 153 to the required gloss to match with the existing complete all as specified and shown on drg. 155 TABLE PEG DRG NO FD-277 & 25(M): (For Item No 155 to 160)Taking out unsvlegs and S&F new legs made of 1st class seasoned teak wood free from knots and cracks with permissible moisture contents throuh out as per shape and size complete all as specified on drawing and directed 156 Same as per item ser No. 155 but long rail complete all as specified and shown on drg. 157 Same as per item ser No. 155 but short rail complete all as specified and shown on drg. 158 Taking out old unservicable top and S&F Top of table shall be madeof 18/19 mm prelaminated HDHMR board Grade I, Type -II ISI Mark- 1514587:1998) (exterior grade).Complete all as spceified 159 Supply & Fixing of new stiffner of size 400x50x25mm made of 1st class seasoned teak wood free knots and cracks with permissible moisture contents complete all as specified and directed 160 Preparation of surfaces by sand papering and cleaning/scrubbing and polishing with french polish upto the required finish to the parts replaced/repaired item No 155 to 159 to match with the existing complete all as specified and shown on drg.
|
