|
Tender For Special Repair To Bldg No Bj/8, Bj/10 And Bh/1 At Albert Ekka Enclave Under Ge Panagarh; 2 Taking downcement plaster ofany description from brick wallsurfaces etc including racking out joints and hacking for key, scrubbing down with water etc., complete all as specified and directed. 3 M&L Rendering 10 mm thick cement plaster in Cement Mortar 1:6 on other than fair faces of brick/concrete work surfaces finished even and smooth (without using extra lime or cement) including taking down old unserviceable cement plaster, complete all as specified and directed. 4 M&L Rendering 15 mm thick cement plaster in Cement Mortar 1:4 onfair faces of brick/concrete surfaces with finished even and smooth without using extra cement and using water proofing compound admixture as per manufacturer"s instruction including taking down old unserviceable cement plaster, complete all as specified and directed.[Note : WPC will measuered and paid separatly under relevant item of schedule.] 5 M&L Rendering 10mm thick on fair faces of ceiling / chajja concrete surfaces in cement mortar 1:3finished even and smooth (without using extra lime or cement) with chicken wire mesh, complete all as specified and directed. 6 Supply only liquidwater proofing compound, complete all as specified and directed. 7 M&L TMT mild steel bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed)not less than 0.90mm dia or securing with clip, complete all as specified and directed. 8 M&L TMT mild steel bars 6mm to 8mm dia ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed)not less than 0.90mm dia or securing with clip, complete all as specified and directed. 9 M&L Reinforced Cement Concrete (design mix), M-25 (using 20mm graded stone aggregate) as in slab supported on wall, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc. including demolition of old unserviceable Reinforced Cement Concrete, complete all as specified and directed. 10 M&L Reinforced Cement Concrete (design mix), M-25 (20mm graded aggregate) for chajjas including demolition of old unserviceable Reinforced Cement Concrete, complete all as specified and directed. 11 Use and waste of Formwork to soffits of suspended slab such as roof slabs, floor slabs, landing and similar works not exceeding 200mm thick (horizontal or sloping), surface of concrete flat for rough finished surface of concrete, complete all as specified and directed. 12 Use and waste of Formwork to chullah hoods, chajjas, troughs and similar items including edges etc surface of concrete flat with fair finished surfaces, complete all as specified and directed. 13 M&L 75mm Plain Cement Concrete 1:3:6 type C1 (using 20mm graded stone aggregate) fininshed the as in plinth protection surfaces even and smooth without using extra cement, including demolition of old unserviceable Plain Cement Concrete, complete all as specified and directed. 14 M&L forming construction joint 30mm deep X 10mm wide with sealing compound grade A, complete all as specified and directed. 15 M&L in repairs providing plain cement concrete, type B0, 1:2:4 (using stone 12.5mm graded aggregate) as in coping to chajja tops and all other similar works, complete all as specified and directed. 16 M&L (a) providing and laying water proofing treatment of sunken portion of WCs, bathroom incl by taking out/demoliton/dismantling of old unserviceable peeled/leaking sunken floors etc & applying cement slurry with acrylic based modified cementitaous composite compound coating of make as approved in technical instruction 5/2003 (b) First layer of slurry of cement @ 0.5 Kg/Sqm mixed with acrylic based polymer modified cementatious composite compounds @ 0.250 Kg/Sqm. This layer will be allowed to air cure for 4 hours. (c) second slurry of cement @ 0.500 Kg/Sqm mixed with acrylic based polymer modified cementatious composite compounds @ 0.250 Kg/Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (d) 200 micron thick polythene film pasted with the help of bituminous adhesive shall be provided over treatment. (e). Plain Cement Concrete in 1:5:10 using brick aggregate as in filling of sunken floors, complete all as specified and directed. 17 S&F in repairs vitreous China squatting pan, "Orissa patteren, size 580 x 440 mm white, with integral footrests (excluding flushing cisteren and flush pipe) including trap set in and including concrete, complete all as specified and directed. 18 S&F in repairs vitreous china wash down closet pan white, pedestal pattern pedestal pan and trap (excluding flushing cistern and flush pipe), connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc and including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel CP or aluminised hinging device including CP jet spray, complete all as specified and directed. 19 S&F in repairs vitreous China wash basin white, flat back,size 550X450 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets including cutting for pinning in ends of brackets or erecting stand including waste pipe, complete all as specified and directed. 20 S&F in repairs 10 litre capacity PVC low level flushing cisternwith all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size complete (with brackets), incl flush pipe of plyethene of low or high density of PVC 32mm dia for low level cistern, complete all as specified and directed. 21 S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and directed. 22 S&F in repairs 15mm bore, fancy type, stop valve/angle cock (multiple) , chromium platedconcealed type cast copper alloy, screwed down , high pressure , with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed. 23 S&F in repairs PVC connection 15mm size PTMT nuts of length 450mm, complete all as specified and directed. 24 S&F in repairs 15mm bore long neck pillar taps cast copper alloy,with capstan heads,chromium plated,screwed down, fancy type high pressure, with or without lettred "HOT or COLD" with long screwed sunk and fly nuts, complete all as specified and directed. 25 S&F in repairs bib taps, cast copper alloy 15mm bore long neck body with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed. 26 S&F wall mixer chromium plated, 3 way including telephonic shower arrangement with connecting legs, wall flanges & wall bracket for hand shower, complete all as specified and directed. 27 S&F as in chromium plated grating, square with waste hole, 150mm size of PTMT(minimum 100 gms), complete all as specified and directed. 28 S&F in repairs 600X450 mm bevelled edge mirror of selected quality glass, mounted of 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup, complete all as specified and directed. 29 S&F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including 40mm dia PVC waste pipe, complete all as specified and directed. 30 S&F in repairs tubular towel rail brass chromium plated 20 mm dia `D" type 60 cm long between flanges, complete all as specified and directed. 31 S&F in repairs chromium plated shower roses 125 mm longwith or without swivel joints, any size, including fixing fixing to steel pipe or union, complete all as specified and directed. 32 S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed. 33 S&F in repairs glass corner shelf with SS guard and railing (size- 200mm x200mm) for bathroom, complete all as specified and directed. 34 S&F in repairs stainless steel kitchen plate rack made out of 0.65mm thick of approved make with plugs, washers, over all size 786mmx610mmx254mm, complete all as specified and directed. 35 M&L 25 mm thick Plain Cement Concrete 1:2:4 type B-0 (Using 12.5mm graded crushed stone aggregate) as in floor, finished the surfaces fair & even to receive floor finishes,including dismantling of old unserviceable Plain Cement Concrete complete all as specified and directed. 36 M&L Non Skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cemeent to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in Cement Mortar 1:6, including dismantling of old unserviceable floor hearth & wall tiling, .complete all as specified and directed. 37 M&L Non Skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqmon vertical surface such as skirtings etc. set and jointed in cement slurryover 10 mm thick rendering in Cement Mortar 1:3including dismantling of old unserviceable floor hearth & wall tiling, complete all as specified and directed. 38 M&L Non Skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exc. 0.11 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in Cement Mortar 1:4including dismantling of old unserviceable floor hearth & wall tiling, complete all as specified and directed. 39 M&L Glazed ceramic tiles Coloured 300x450mm 7 to 8 mm thick in wall/dado etc, set & jointedin neat cement slurry & pointed in white or coloured cement to match renderingover 10 mm thick in Cement Mortar 1:3 on stone masonry surfaces or surfaces other than fair face of brick work/ concrete surfacesincluding dismantling of old unserviceable floor hearth & wall tiling, complete all as specified and directed. 40 M&L 16-18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite of any type of workincluding dismantling of old unserviceable stone work, complete all as specified and directed. 41 M&L 18 to 20mm thick green marble (table rubbed and polished) in steps, jambs, pillars, window cills,bathroom corners cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with green marble shadeincluding dismantling of old unserviceable stone work, complete all as specified and directed. 42 Rounding to edges of stone slabs exposededge, such as in steps, cooking platform and othersimilar situation, complete all as specified and directed. 43 M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete lad over cement screed and jointed over screed bed or bedding layer of mortar 20mm thick in Cement Mortar 1:6 for laying floor finishincluding dismantling of old unserviceable stone work, complete all as specified and directed. 44 M&L Kota stone slab 14-16mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with ditto as per item 1.042 above over 10mm thick in cement mortar Cement Mortar 1:3 including dismantling of old unserviceable stone work, complete all as specified and directed. 45 Taking down chowkats or frames exc 1.5 sqm but n. exc 4 sqm each with shutters (without taking off shutters from the frame), complete all as specified and directed. 46 Taking down of chowkats or frames not exc 1.5sqm each with shutters (without taking off shutters from frames), complete all as specified and directed. 47 S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows and other frames/chowkhat of size 50x100 mm comprising of virgin PVC polymer of K value 58-60 (suspension grade ), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS scews having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200N (face) and 1100N (Edge), minimum compressive strength of 58 N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length, complete all as specified and directed.[Note : (i) M.S. hold fast/lugs or SS dash fasteners shall be paid for separately.(ii) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile demension on plus side shall be acceptable but no extra payment on this account shall be made.] 48 S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows and other frames/chowkhat of size 50x125 mm comprising of virgin PVC polymer of K value 58-60 (suspension grade ), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS scews having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200N (face) and 1100N (Edge), minimum compressive strength of 58 N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length, complete all as specified and directed.[Note : (i) M.S. hold fast/lugs or SS dash fasteners shall be paid for separately.(ii) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile demension on plus side shall be acceptable but no extra payment on this account shall be made.] 49 S&F factory made single extruded WPC (wood polymer composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers(wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum frame density of 650 kg/cum, screw withdrawal strength of 1800N (face) and 900N (Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steelbutt hings of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.[Note : Stainless steel butt hinges and necessary SS Screws shall be paid separately.] 50 S&F 35mm thick factory made single extruded WPC shutter (wood polymer composite) solid wire gauzed i.e. panel will be of wire gauze in lieu ofpanel. The comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers(wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum frame density of 650 kg/cum, screw withdrawal strength of 1800N (face) and 900N (Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steelbutt hings of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.[Note : Stainless steel butt hinges and necessary SS Screws shall be paid separately.] 51 S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. 52 S&F MS flat iron as in hold fast clamps small articles conforming to FE-290 Gde-E-165, complete all as specified and directed. 53 M&L Plain Cement Concrete (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in bed blocks for hold fast including necesssary formwork, complete all as specified and directed. 54 S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed. 55 S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing, complete all as specified and directed. 56 Dismantling wooden boarding, any description, fixed in any position with nails, complete all as specified and directed. 57 S&F 18/19mm thick prelaminated PVC plain solid board for shelves/wordrobes etc and fixed with screws to PVC frame workincl in this item rate, complete all as specified and directed. 58 S&F 18/19mm thick prelaminated PVC soild board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination for shutters, fixed with angle frame work incl stainless steel hinges andf magnet catcher, complete all as specified and directed. 59 S&F Continuous (piano) hinges,width of flaps 40mm stainless steel, bright finish or electrogalvanised, complete all as specified and directed. 60 S&F factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 122 x 54 mm & sash 47 x 64 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed.[Note : (i) Glass or wiremesh shall be paid separately.(ii) For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.] 61 M&L sheet glass 4.8 mm thick ordinary quality and glazing with oil putty and pin in square n. exc 0.50 sqm in each pan, complete all as specified and directed. 62 M&L 4mm thick figured glass, pin head type and glazing with oil putty or with brass screws in square n.exc 0.50 sqm in each pan for bathrooms/toilets ventilators, complete all as specified and directed. 63 S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 , the grill shall be inserted in the wall surface including necessary drilling and grouting with cement etc, complete all as specified and directed. 64 S&F 100mm long butt hinges(ISI marked), extruded alluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified and directed. 65 S&F 75mm long butt hinges (ISI marked), extruded alluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21, complete all as specified and directed. 66 S&F aluminium anodised (ISI marked) 150 mm barrel tower bolts of extruded section, complete all as specified and directed. 67 S&F aluminium anodised (ISI marked) 100mm barrel tower bolts of extruded section, complete all as specified and directed. 68 S&F 150 mm long aluminium alloy handles (ISI marked),fabricated type, anodised, complete all as specified and directed. 69 S&F 100 mm long aluminium alloy handles (ISI marked), fabricated type, anodised, complete all as specified and directed. 70 S&F 300 mm long aluminium alloy (ISI marked), anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed. 71 S&F 75 mm long hasp and staple (ISI marked), aluminium anodized with bolt to hinge plate and fixed with screws, complete all as specified and directed. 72 S&F 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and directed. 73 S&F 300 mm mild steel ordinary rat tail rod pattern spring including roller and sollar plates, complete all as specified and directed. 74 S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasketetc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required includingAluminium snap beading for glazing/ paneling,all complete as per architectural drawings and complete all as specified and directed. 75 S&F Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and complete all as specified and directed. 76 S&F in repairs harrison curtain rails, mild steel,chromium plated with conical end balls suitable for fixing as end of curtain/dropery rods, complete all as specified and directed. 77 Taking up or down steel tubing and connection including cleaning for refixing or removed to store, 15 mm dia bore, complete all as specified and directed. 78 Taking up or down steel tubing and connection including cleaning for refixing or removed to store, 20 mm dia bore, complete all as specified and directed. 79 Cutting chases, pinning in making good to facing on brick walls where required and pointing in cement mortar (1:3) to ends for concealed water tubing and making good, cutting n. exc. 10cm girth, complete all as specified and directed. 80 S&F 20 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors, complete all as specified and directed. 81 S&F 25 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors, complete all as specified and directed. 82 Dismantling of cast iron 100 mm dia pipes jointed in cement mortar, complete all as specified and directed. 83 S&F PVC SWR pipes 150 mm bore single socketed in any length with rubber ring joint fixed to wallwith steel clamps for rain water pipes, complete all as specified and directed. 84 S&F PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joint fixed to wallwith steel clamps, complete all as specified and directed. 85 S&F PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joint , laid in trenches or in floors including dismantling of old unserviceable CI pipe, complete all as specified and directed. 86 S&F PVC SWR bends of 150 mm bore, complete all as specified and directed. 87 S&F PVC SWR bends of 110 mm bore, complete all as specified and directed. 88 S&F PVC SWR bends of 75 mm bore, complete all as specified and directed. 89 S&F PVC (SWR) junction single (single T) equal or unequal provided with access door of 110 mm dia, complete all as specified and directed. 90 S&F PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia, complete all as specified and directed. 91 S&F PVC (SWR) vent cowl 110 mm bore, complete all as specified and directed. 92 M&L PVC (SWR) gully trap 125/110 mm setting and jointing with solvent cement, complete all as specified and directed. 93 S&F in repairs for Gun metal gate valve, 20 mm bore, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed. 94 M&L old size brick work with fly ash bricks straight or curved on plan exc 6 m mean radius build in Cement Mortar 1:6 including dismantling of old unserviceable half brick work, complete all as specified and directed. 95 M&L brick work with half bricks thick fly ash bricks straight or curved on plan exc 6 m mean radius build in Cement Mortar 1:4 including dismantling of old unserviceable half brick work, complete all as specified and directed. 96 M&L prepration of newly plastered surfaces of wall and applying two coat of oil bound distemper over one coat of alkali resistanse primer over a coat of 1mm thick wall care putty, complete all as specified and directed. 97 M&L complete removal of old treatment on old plastered surfaces of wall and applying two coat of oil bound distemper over one coat of alkali resistanse primer over a coat of 1mm thick wall care putty, complete all as specified and directed. 98 M&L prepartion of newly plastered ceiling surfaces and applying three coat of white wash, complete all as specified and directed. 99 M&L complete removal of old treatment from old plastered ceiling surfaces and applyingthree coat of white wash, complete all as specified and directed. 100 M&L prepration of new plastered surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed.[Note : Min 5 (five) years guarantee certificate from manufacturer shall be submitted before issue of completion certificate.] 101 M&L complete removal of old treatment from old plastered surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed.[Note : Min 5 (five) years guarantee certificate from manufacturer shall be submitted before issue of completion certificate.] 102 M&L preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer of any description not otherwise described over 10cm width or girth, complete all as specified and directed. 103 M&L writing letters or figures (block, Roman, Italic or indian) n exc 30 cm, complete all as specified and directed. 104 S&F PVC waste pipe 32mm dia for wash basin 3.00 mtr complete all as specified and directed. 105 S&F PVC waste pipe 32mm dia for wash basin 3.00 mtr, complete all as specified and directed. 106 Roof treatment to be concluded in stages as mentioned below. complete all as specified and directed: -STAGE I:M&L 25 mm thick average Plain Cement Concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in padding concrete on roof over two coat of high performance SBR based multipurpose polymer for water proofing, repair & bonding at the ratio of 1:3:8 (Latex :Water:Cement) in a criss cross way, including demolition of old unserviceable concrete treatment, rendering, old APP (in roof) & removing the same & cleaning thoroughly the base surface, complete all as specified and directed.[Note : (i) Second coat of latex is laid down minimum interval of 6-8 hours of first coat of latex and after second coat of latex immediate applied plaster work(ii) Make - Sika latex- power or similar make as mentioned in list of make in PS]STAGE II:M&L Plain Cement Concrete(1:2:4) type B-0 (using 20mm graded aggregate) as in roof kerbs or mud stop rounded including demolition of old unserviceable one. 107 Item No. 1.105 Contd….STAGE III:M&L in repairs rendering 10mm thick on fair faces on roof surfaces of concrete surfaces in cement mortar 1:3 finished even and fair includingusing water proofing compound admixture as per manufacturer"s instructions, [Note : WPC will measured and paid separately under relevant item of schedule.]STAGE IVS&F & Providing water proofing treatment with a layer of APP based polymeric membrane 3mm thick minimum weighing 3.60 to 4.00 kg/sqm reinforced with polyster non wove fabric (wt. not less than 160 gms/sqm) shall be applied over one coat of cold bituminous primer @ 0.40 ltr/sqm (membrane shall be laid using butane torch sealing all joints etc and also include two coat of aluminium paint over APP based polymeric membrane complete all as specified and directed.[Note: The over lap shall be of minimum 75mm in longitudinal direction and 100mm on transverse direction] 108 Dismantling wrought iron or mild steel work of any description not otherwiseprovided for, complete all as specified and directed. 109 S&F Joist channel angle of tee section fixed independently without connecting plate as Fe 410 W (Gde-E-250 quality A), complete all as specified and directed. 110 M&L Plain Cement Concrete 1:3:6, type C2(using 40 mm graded stone aggregate) as in foundation filling and mass concrete, complete all as specified and directed. 111 M&L concrete bed to 150mm dia drain pipes including packing under,and haunching against the sides of pipes after they are laid and tested in Plain Cement Concrete 1:3:6 type C2 (using 40mm graded stone aggregate) including demolition & breaking up 150mm dia old unserviceable drain pipes, complete all as specified and directed. 112 Supplying and laying UPVC Eco drain Hi-tech pipe drainage sewer system pipe bearing 160mm dia minimum 4mm thick including jointing with coupler, bend tee as per site requirement complete laid in trenches or floors, complete all as specified and directed. 113 M&L precast cement concrete cover Type B-1,1:1.5:3(using 20mm graded crushed stone aggregates) set in cm 1:4 as in mahhole cover etc., complete all as specified and directed. 114 SCH A PART-II : INTERNAL ELECTRIFICATION 115 Taking down carefully aluminium conductor point wiring (light,fan,socket or power) completeincluding fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing(except those to be reused shall be kept in safe custodyat the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing, complete all as specified and directed. 116 M&L point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one wayswitch using1.5 sqmm nominal cross sectional areamultistrandedcopper conductor ,PVC insulated unsheathedFRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes/ modular, 3 mm thick bakelite sheet top cover (ISI Marked)fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLSHPVC insulated unsheathed earth wire and connecting to earth dolly andbrass screws, washers etc., complete all as specified and directed. 117 All as per item No. 2.02 above but 5 Amp socket on same boardwith other switches, complete all as specified and directed. 118 All as per item No 2.02 above but 5 Amp socket on Independent boardwith other switches, complete all as specified and directed. 119 All as per item No. 2.02 above but 5 Amp Calling bell point with other switches, complete all as specified and directed. 120 All as per item No. 2.02 above but 5 Amp Two way point with other switches, complete all as specified and directed. 121 M&L wiring for socket outlet 3 pin, 15 ampson independent Boardscontrolled by one, one wayswitch using4.0 sqmm nominal cross sectional area multistrandedcopper conductor, PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, includingpressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked)fitted with Chromium plated brass screws & washers and 4.0 sqmm nominal cross sectioanl area multistranded copper conductor, PVC insulated unsheathed FRLSH cable earth wire and connecting to earth dolly andbrass screws, washers etc., complete all as specified and directed. 122 S&F in repairs switch piano flush type, single pole, 5/6 Amps, one way, complete all as specified and directed. 123 S&F in repairs Bell switch piano flush type, single pole, 5/6 Amps, one way, complete all as specified and directed. 124 S&F in repairs switch piano flush type, single pole, 6/16 Amps, Two way, complete all as specified and directed. 125 S&F in repairs socket outlet 2 in 1 multipurpose5 pin, (6 Amps) flush typecontrolled by one switch duly marked, complete all as specified and directed. 126 S&F in repairs switch socket combination 2 in 1 multipurpose 5 pin, (6 Amps) flush type controlled by one switch, complete all as specified and directed. 127 S&F in repairs switch socket combination 3 pin, (16 Amps) flush typecontrolled by one switch, complete all as specified and directed. 128 S&F in repairs Bell multi music type, AC 230 Volts, single pole 230 volts, complete all as specified and directed. 129 S&F in repairs ceiling rose surface bakelite 45 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps, complete all as specified and directed. 130 S&F in repairs stepped type electronic (min 5 steps) fan regulator flush type 240 Volts ISI marked, complete all as specified and directed. 131 S&F in repairs lamp holder, polycarbonatebody with back plate straight or angular suitable for batten fittings, complete all as specified and directed. 132 S&F in repairs submain two single core, 6 sqmm nominal cross sectional areamultistrandedcopper conductor FRLSH cable, PVC insulated unsheathed 1100 Volts gradedrawing in and including nd including suitable sizePVC conduit (ISI marked),concealed, including 6 sqmm nominal cross sectional areamultistrandedcopper conductor FRLSH cable, PVC insulated unsheathed 1100 Volts grade earth wire, complete all as specified and directed.[Note : (i) Colour code for cable must be followed as per IS standards(ii) 2 run of 6.00sqm main wire one run of 6.00 Sqm earth wire & necessary PVC conduit withfittings, shall be considered as one run.] 133 S&F in repairs wall security light fittings 35 watts 230V, minimumm lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65/66 including necessary connection completewith all accessories including connected with 3 core copper cable of suitable 1.5 sqmm size, complete all as specified and directed. 134 S&F in repairs 10 W LED light fitting mirror type 2", 220volt AC lighting fixture with complete all accessories and connection from ceiling rose with twin core twisted flexible copper conductor cable with suitable size and earthing, complete all as specified and directed. 135 S&F in repairs LED light fitting 1x 20 W LED surface mounting general purpose ultra slim economical LED Battens in extruded PC housing and square to suit variety of application areas connedting up with complete all accessories and connection from ceiling rose with twin core twisted flexible copper conductor cable with suitable size and earthing complete, complete all as specified and directed. 136 S&F in repairs Decorative wall light, fixture made up of polycarbonate suitable for 9W LED lamp B22 base, complete all as specified and directed. 137 S&F in repairs 12 watt surface mounted square LED Down light Colour (CW) aesthetically designed made by aluminium P-die-cast enclousers, with separate replaceable constant current driver 12 watts for grid ceilling including electrical connection, complete all as specified and directed. 138 S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) without remote after taking down/ dismantling of existing ceiling fan from ceiling & depositing in the MES store room , complete all as specified and directed.[Note : Old existing fan to be deposited in MES store & necessary RV & ledger No. to be obtained] 139 S&F exhaust ventilation fan with louvers of sweep 250mm, 230 volts 1200 Rpm, with blade and frame and louvers sturdy engineering plastic complete with suitable size of hole, ISI marked after taking down/ dismantling of existing ceiling fan from ceiling & depositing in the store room, complete all as specified and directed.[Note : Old existing fan to be deposited in MES store & necessary RV & ledger No. to be obtained] 140 S&F exhaust ventilation fan with louvers of sweep 225mm, 230 volts 1200 Rpm, with blade and frame and louvers metal body complete with suitable size of hole, ISI marked, after taking down/ dismantling of existing ceiling fan from ceiling & depositing in the store room, complete all as specified and directed.[Note : Old existing fan to be deposited in MES store & necessary RV & ledger No. to be obtained] 141 S&F electric water heater (Geyser) storage type steel body with copper inner tank and heating element upto 2KW capacity 25 Litres, BEE 5 star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc after taking down/ dismantling of existing geyser & depositing in the store room, complete all as specified and directed.[Note : Old existing fan to be deposited in MES store & necessary RV & ledger No. to be obtained] 142 S&F in repairs epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Single pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel, neutral link and incoming contact, complete all as specified and directed.[Note : Cable fixed with suitable size Lux and blanker fill with blanker.] 143 S&F in repairs epoxy powder coated sheet metal enclosure for DBs, Double door (when MCBs to be used), tripple pole and neutral 415 V, 4 ways with mounting fitted with bus bar, DIN channel, neutral link and incoming contact, complete all as specified and directed.[Note : Cable fixed with suitable size Lux and blanker fill with blanker.] 144 S&F in repairs 240V, 10 KA "C" curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning, complete all as specified and directed. 145 S&F in repairs MCB SPN 32 Amps, "C" series 10kA, 240 Volts and to be housed in DBs complete including necessry connection, complete all as specified and directed.[Note : Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating.] 146 S&F in repairs MCB TPN 25-63 Amps, "C" series 10kA, 415 Volts and to be housed in DBs complete including necessry connection, complete all as specified and directed.[Note : Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating.] 147 S&F in repairs 63 Amp MCCB 4 pole, 3 phase, 415 volt of capacityAmp, 16 KA complete with proper copper thimbles, copper reducer etc., with fixed thermal & magnetic setting complete all as specified and directed.[Note : cable fixed with suitable size Lux and blanker fill with blanker.] 148 M&L Earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth wire electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth wire encased inand including 40 mm dia GI "lightgrade" pipe from upper end of earth plate upto equipments,20 dia bore GI pipe "light grade" as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe andPlain Cement Concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and Reinforced Cement Concrete pit cover 50mm thick precast Reinforced Cement Concrete 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in Electrical Plate No-3 of SSR Part-I complete all as specified and directed and testing on completion.[Note : Ifthe desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department.] 149 S&F in repairs of high pressure PTMT float valve with epoxy coated alluminium rod and high density polythene ball screwed for irom pipe 25 mm bore dia with fly nut, complete all as specified and directed. 150 S&F in repairs 25mm bore GI tubing medium grade in trenches / Floor / pillar connetion in old or new postion including fittings including taking down old unseviceable pipe, complete all as specified and directed. 151 S&F in repairs 40mm bore GI tubing medium grade in trenches / Floor / pillar connetion in old or new postion including fittings including taking down old unseviceable pipe, complete all as specified and directed. 152 S&F in repairs 25 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes, complete all as specified and directed. 153 S&F 40 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes, complete all as specified and directed. 154 S&F in repairs capacity 500 Ltrs rotational moulded polyethylene water storage tanks 3 layered, white, anti bacterial, UV resistant, Threaded lid, anti microbial, 100% virgin food grade plastic, prevent algae growth, anti viral/ bacterial/ fungal/ algae properties, (Cylindrical, vertical with closed top) complete including provision of all inlet outlet overflow and drain pipe fittingincluding taking down unserviceable tank, complete all as specified and directed. 155 M&L XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16sqmmx4core laying properly in trench including dismantling old unserviceable cable, complete all as specified and directed. 156 Excavation in trenches not exceeding 1.5m wide and not exc. 1.5m depth and getting out in soft/loose soil, complete all as specified and directed. 157 Returning, filling, including spreading, leveling, watering and well ramming in layers not exc. 25cmin soft/loose soil, complete all as specified and directed. 158 Removal of excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point, complete all as specified and directed. 159 Supply and lay for dry river sand filling for cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying, complete all as specified and directed.[Note : Punned thickness shall be measured.] 160 M&L sub class B fly ash bricks locally available of size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable, complete all as specified and directed. 161 S&F GI Light grade 40 mm dia of size for road cross/cutting on wall floor drain etc., complete all as specified and directed.
|
