|
Eight-Port Charger For 1-2S Batteries. - Six-Port Charger For 1–2S. 1. 29 Pcs. 2. Support/Battery Type 1S Lipo/Lihv (3.7V/4.35V) And Sometimes 2S (7.4V). 3. Number Of Ports 6 Independent Ports. 4. Output Voltage Of The Port Is At Least ~4.20V (For 1S Lipo) / ~4.35V (For 1S Lihv). 5. Output Charging Current From ~0.2 A To ~1 A Per Port. 6. Input Voltage / Power Supply Usb Type C / Dc Adapter / Xt60 / 5-12V. 7. Maximum Power (In Total / Per Port) Up To ~30W - In Total, Or ~1 5W Each. 8. Low Input Voltage Protection, Short Circuit Protection, Overheat Protection. 9. Indication - Designed To Receive Signals From Status Leds (Charge / Full Charge), Sometimes A Display Indicating The Port Voltage. 10. Operating Temperature Range Is Approximately 0-40°C Or Slightly Wider. - Power Cable. 1. 29 Pcs. - User Instructions. 1. 29 Pcs. - Adapters Or Adapters. 1. 29 Pcs., External Signal Receiver With Monitor. -External Video Signal Receiver With Monitor For Fpv. 1. 9 Pcs. 2. Screen Diagonal Is At Least 7 Inches. 3. Display Resolution Of At Least 800×480 Or 1024×600 Pixels (Depending On The Model). 4. Screen Type Tft Lcd, Matte Or Glossy. 5. Reception Frequency Range 5.8 Ghz. 6. Receiver Type: Single Or Diversity (Double Receiver For Better Signal). 7. Power Supply: Built-In Battery (Usually 2000–3000 Mah) Or 7–12 V Dc. 8. Operating Time From 1 To 3 Hours. 9. Video Recording (Dvr) Is Available. 10. Outputs/Inputs Av-In/Out, Miniusb, Slot For Microsd. 11. Additionally, Sun Visor, Tripod Mount, Osd Menu. - Sma/Rp-Sma Plug. 1. 9 Pcs. - Battery (Built-In Or Removable). 1. 9 Pcs. - Power Cable/Charger. 1. 9 Pcs. - Mount / Stand / Sun Visor. 1. 9 Pcs. - Operating Instructions. 1. 9 Pcs., Rf Modules Tx For Remote Controls At Least 868/915 Mhz. -Rf Modules 868/915 Tx. 1. 29 Pcs. 2. Frequency Range Of At Least 868/915 Mhz. 3. Output Power (Rf Output Power) Not Less Than 2000 Mw. 4. Compatible Expresslrs Or Tbs Crossfire System. 5. Lora Modulation. 6. Telemetry Bidirectional (Tx ↔ Rx). 7. Refresh Rate From 50 To 250 Hz. 8. The Interface For Connecting To The Jr Remote Control Is Compatible. 9. Power Supply Of At Least 12 V. - Adapter Board / Interface Board. 1. 29 Pcs. - Antenna Adapter Cables. 1. 29 Pcs. - Cooling/Fan. 1. 29 Pcs. - Fastening Elements. 1. 29 Pcs. - Instructions/Documentation. 1. 29 Pcs. - Housing/Casing. 1. 29 Pcs. - Antenna. 1. 29 Pcs. - Cables To The Remote Control. 1. 29 Pcs., Protective Case For Batteries. -Protective Case For Fpv Batteries. 1. 29 Pcs. 2. Capacity Up To 20 Batteries. 3. Housing Material: Fire-Resistant Fabric (For Example, Fiberglass With Aluminum Coating), Hard Plastic, Aluminum. 4. Fire Resistance (In Fireproof Models) - Withstands Internal Battery Fire. 5. Design Type: Removable Cover/Hinged Cover With Zipper Or Locks. 6. Type Of Partitions: Hard Or Soft Dividers (Fixed Or Adjustable). - Internal Cells Or Partitions. 1. 29 Pcs. - Foam Rubber / Shock-Absorbing Inserts. 1. 29 Pcs. - Locks Or Latches. 1. 29 Pcs. - Carrying Handle. 1. 29 Pcs. - Valve For Ventilation. 1. 29 Pcs. - Shoulder Strap. 1. 29 Pcs. - Instructions Or Markings. 1. 29 Pcs., Analog (Digital) Fpv Glasses. -Glasses. 1. 29 Pcs. 2. Screen At Least 5 Inches 3. Screen Resolution At Least 800 × 480 Pixels. 4. Receiver At Least 5.8 Ghz, Up To 40 Channels With Raceband Support. 5. Diversity Of At Least Two Receivers (Diversity). 6.Recording (Dvr) Internal Recording On Microsd, Maximum Recording Resolution - Up To 720 × 576 Pixels. 7. Battery Built-In Li-Polymer Battery (Not Less Than: 1200 Mah, 7.4 V). 8. Operating Time Is At Least 2 Hours. 9. Viewing Angle Up To 82°. 10. External Power Can Be Powered By An External Source (Such As 2S/3S Lipo). 11. Rp Sma Antenna Connector. -Antennas (Usually 2 Pieces - One Linear, One Circular). 1. 29 Set. -Battery (Built-In Or External). 1. 29 Pcs. -Av Video Cable. 1. 29 Pcs. -Charging Cable Or Adapter. 1. 29 Pcs. -Mount On The Head. 1. 29 Pcs. -User Instructions. 1. 29 Pcs. -Case Or Soft Case. 1. 29 Pcs. -Dvr Memory Card. 1. 29 Pcs. -External Receiver Or Module Slot. 1. 29 Pcs. - Otg Cable. 1. 29 Pcs., Control Panel Supporting Elrs, Tbs Crossfire Or Multi Protocol Protocols. -Remote Controller. 1. 29 Pcs. 2. Multi-Protocol Module With Expresslrs (Elrs) And External Jr Module Bay. 3. Stick Hall Sensors (Precise, Non-Contact). 4. Up To 16 Channels. 5. Switches 4 Three-Position, 2 Two-Position, 2 Rotary Knobs (Potentiometers), 2 Buttons (Momentary). 6. Edgetx Os. 7. Display Of At Least 128×64 Monochrome Lcd Display. 8. 2×18650 Batteries Or 2×Li-Ion/Lipo (Up To 8.4 V). 9. Connectors And Connection Usb-C: For Charging And Simulators, Sd Card: Microsd (For Models, Scripts, Logs), Trainer Port: Yes (Training Mode). -Mkii Transmitter (With Sticks And Switches Installed). 1. 29 Pcs. -2.4 Ghz Antenna. 1. 29 Pcs. -2×18650 Batteries. 1. 29 Set. -Usb-C Cable (For Charging And Connecting To A Pc/Simulator. 1. 29 Pcs. -User Manual (Instructions) And Warranty Card. 1. 29 Pcs. -Branded Quality Control Card (Qc Card). 1. 29 Pcs. -Protective Box/Packaging. 1. 29 Pcs., Rf Tx Modules For 2.4 Ghz Remote Controls. -Rf Modules 2.4 Tx 1. 29 Pcs. 2. Operating Frequency 2.4–2.4835 Ghz. 3. Modulation Type Gfsk, Dsss, Ook, Fsk. 4. Transmission Power. +10 Dbm. 5. Receiver Sensitivity: -100 To -110 Dbm. 6. Maximum Data Transfer Speed From 250 Kbps. 7. Power Supply Not Less Than 3.3 V. 8. Current Consumption. From 30–40 Ma. 9.Standby Mode: Less Than 1Ua. 10. External Antenna Of At Least 50 Ohms. 11. Compact Sizes, For Example, 16X24 Mm And Smaller. - Antenna. 1. 29 Pcs. - Board With Microcontroller. 1. 29 Pcs. - Cables And Connectors. 1. 29 Pcs. - Housing Or Fastener. 1. 29 Pcs. - Instructions And Documentation. 1. 29 Pcs. - Software (Optional). 1. 29 Pcs., Directional Antenna. - Fpv Directional Antenna 1. 29 Pcs. 2. Frequency Range Up To 5.4 Ghz. 3. Gain Up To 21 Db. 4. Swr From <1.8. 5. Max. Power Not Less Than 50 W. 6. Dimensions No Less Than 21×18×4.3 Cm. 7. N(F)-Type Connector. - Fastening Elements. 1. 29 Pcs. - Cable With Connectors. 1. 29 Pcs. - Installation And Configuration Instructions. 1. 29 Pcs. - Adapter. 1. 29 Pcs. - Adapter. 1. 29 Pcs., Charger For 6-8S Batteries, Two Ports. - Dual Port Charger For 6-8S Batteries For Fpv. 1. 29 Pcs. 2. Supported Number Of Cells (S) 6-8S (Lipo / Lihv / Liion, Etc.). 3. Number Of Ports 2 Independent Output Ports. 4. Input Voltage Range Of At Least Dc ~10-30 V. 5. Maximum Charging Current (Per Port) From ~0.1-15 A. 6. Maximum Charging Power (Per Port And In Total) From ~200 W To 300-600 W And Above. 7. Balancing (Balance Current) ~1 A. 8. Protection Against Short Circuit, Overheating, Overdischarge, Overvoltage, Control. - Power Cable(S). 1. 29 Pcs. - Balancing Wires / Balancer Connectors. 1. 29 Pcs. - Battery Connectors (Output Leads). 1. 29 Pcs. - User Manual/Operating Manual. 1. 29 Pcs. - Cable For Update/Connection With Pc. 1. 29 Pcs. - Housing / Fastening Elements. 1. 29 Pcs., Soldering Station 220 V, No Less Than 60 W, Designed For Soldering Various Microcircuits And Elements Of An Fpv Drone. The Kit Should Include A Soldering Iron And A Hair Dryer
|
