Lasers – Acquisition Of A Complete Laser Light Emitting Device. Technical Parameters: Laser Head Unit: The Laser Head Unit Consists Of 144 Individual Beams And Together They Form A Single Main Beam. The Laser Can Light Up In Any Color By Mixing Rgb Colors. The Laser Control Can Be Operated In A Pre-Programmed Way, And The Programming Can Be Modified By The User With The Help Of A Computer/Tablet. The Laser Base Head Can Receive Sounds Converted On The Radio Wave, But For This To Work, An Additional Control Unit Is Required. Input Voltage: 110 Vac-240 Vac Input Power: Ac 110V 16A Or Ac 240V 7A Power Requirement: 1600 W Rgb Laser Total Power: 240W Rgb Beam Total: 144 Pcs Divergence: 3 Mrad Modulation Input: 0-5V Dc 10Khz Red Power: 72X840 Mw=60W Red Wavelength: 638 Nm Blue Power: 36X3.6W=130W Blue Wavelength: 445 Nm Green Power: 36X1.2W=43W Green Wavelength: 525 Nm Size: 330X330x400 Mm (13”X13”X15.7”) Weight: 30 Kg (66 Ibs) Ip Classification: Ip 67 Operating Time: More Than 10,000 Hours Warranty: 2 Years, Maximum 6,000 Hours Liquid Cooler An Essential Device For The Operation Of The Laser Head Unit, Which Continuously Circulates Glucose Coolant. The Achievable Temperature Range Is 10-38 °C, The Optimal Target Temperature Is 23 °C. In Winter, The Equipment Is Preheated. Voltage: Ax-1P 220V-240V Frequency: 50/60 Hz Current: 0.6 - 4.9 A Maximum Energy Consumption: 0.76/0.85 Kw Compressor Power: 0.82/0.95 Kw 1.1/ 1.3 Hp Nominal Cooling Capacity: 6040/7098 Btu/H 1.77/2.08 Kw 1521/1788 Kcal/H Maximum Pump Pressure: 0.09 Kw Maximum Pump Flow: 25M Maximum Flow: 15 L/Min Refrigerant: R -134A Accuracy: ±0.3°C Narrowing: Capillary Tank Capacity: 6 Liters Inlet And Outlet: 10 Mm Quick Connector Size: 58X29x47 Cm Net Weight: 25 Kg Gross Weight: 28 Kg Commissioning: The Complete Laser Equipment Was Installed By Ózd, Gyár U ., It Is Necessary To Install It In A Ready-To-Use Condition On Property No. 11274/1 Hrsz. The Foundation Of A Factory Chimney (Width 5.4 M) Will Be Built On The Property, And Approx. 4 M High Open Structural Part (Torso). A Service Room With A Flat Roof (Sandwich Panel) With A Floor Area Of 3 M X 2 M Will Be Created In The Inner Part Of The Chimney, Which Is Used To Place And Store The Laser Equipment And Related Devices. The Cost Of The Construction Of The Chimney Base And The Associated Service Room Is Not Part Of This Request For Proposals. A Free Opening Measuring 350X350 Mm Will Be Created At The Top Of The Service Room, Through Which The Laser Beams Can Exit Freely And Without Obstruction. The Laser Head Unit Must Be Attached To The Sandwich Panel Structure Under The Open Opening At The Top Of The Service Room. All Of The Liquid Cooling Equipment And Additional Accessories Can Be Placed Inside The Service Room. The 1X32 A Power Cord Required For The Operation Of The Equipment Is Available On Site. The Installation Requires The Design Of The Electrical Cabinet And The Cables, Connectors, And Wires Necessary For The Installation Of The Machines
Dear Sir,
Warm Greetings from TenderDetail.com !!
We have received Tender Document request for the TDR No : 79216076
Tender Notice along with it's Attachments ( Tender Document / Scan Image of News Paper)
sent to your Email Address :.
Please check your email for Tender Document.